peripheral problems (USB and ACPI)

Similar Questions

• Peripheral Audio USB-Mulit-channel has a driver problem and PnP device problem.

  I try to use the blue ice pre - amp for recording. Under channel-Mulit-USB Audio Device, device status, it displays "this device cannot start. (Code 10) "once I start the troubleshooting process it shows that even after reinstalling the driver it still does not work and that there is a problem with the device PnP I already tried to uninstall the driver and restart my laptop to let windows try again but nothing works.  Please help D:! Thank you all very much! :]
  -Kyle

  Hello

  1. is this problem limited with a specific USB device?

  2. it worked before?

  3. using this unit for the first time on this computer?

  4. the other USB devices work properly?

  Method 1: Run the troubleshooter and see if it helps.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues. You may need to update the chipset drivers and the USB controller

  Follow the given article below for more information.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  In addition, update the driver from the manufacturer's Web site and see if it helps.

  Method 3: Uninstall and reinstall the USB drivers and check if the problem persists

  1 disconnect all USB devices except the USB keyboard and mouse.

  2. click on start and type device manager in the start search box and press ENTER.
  3. Select the Device Manager and a pop-up window will Device Manager.
  4. click the + on controllers USB Bus to develop it.
  5. right click on all controllers USB and USB Root Hub that is listed, and select uninstall.
  6. restart the computer.
  7. plug in the appliance and check if it works.
   
   
   
   
  I hope this helps.

• How to install this update and resolve problems of USB and the touchpad?

  I Equium M50 (59th) and am bitten by an update that pulled my touchpad and keyboard. I did the new installation of XP Home and have all updated drivers and everything goes well. The last update, what I can't understand is for
  Ana _2005_10_24_V1.2 driver is for, Standard Open HCD USB Host Controller... X 2 .........

  The update addresses all kinds of questions like I'm having and is an update recommended driver detective, I use offten.

  The problem is that it says uninstall the drivers for the i have installed already and when I do it it hits off my USB mouse me leaving no able to install the new. When I reboot it installs those I don't want not reinstalled.

  This is the read me, off the coast of the new update and really I don't understand to underdstand what to do... .so here it is?
  Driver revision history:
  Twinhan VP704A Driver Release Notes
  -------------------------------------------------------------------------------
  Note:
  1. in the event that the system hangs when running with VP704A, please install ULI
  Host USB 2.0 in \ULiUSB20Driver driver

  2. for XP/SP1, please update with the patch in
  

  3. in XP/SP1, update driver will crash the system, while the new facility is ok.
  The trick to update driver XP/SP1 is illustrated in the following steps,
  a. uninstall the driver
  b. disconnect and reconnect the USB device
  c. install the driver
  4 to support the controller remotely, please launch Agent.exe in \Agent.
  Further details at \Agent\Readme.txt

  Known issues:
  1 multi-instance is not supported
  2 remote wakeup is not supported
  3. strong use of the processor from analog video/audio capture
  4. bad Signal using color YUY2 format IST
  5 AV sync if audio captured the wrong filter.
  (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)
  6. noise with analog TV and FM Radio
  (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)

  Driver revision history:
  -------------------------------------------------------------------------------
  2005-10-24, version: 1.0.2.8
  Bugs fixed and new features:
  1 is not correctly configured.
  -------------------------------------------------------------------------------
  2005-10-21, version: 1.0.2.7
  Bugs fixed and new features:
  1. the firmware version read FLASH OK!
  -------------------------------------------------------------------------------
  2005-10-14, version: 1.0.2.6
  Bugs fixed and new features:
  1.MUtil - access driver empty part lower part of screen when IST!
  2.MUtil - access HCT pilot check fix crash!
  -------------------------------------------------------------------------------
  2005-10-07, version: 1.0.2.5
  Bugs fixed and new features:
  1 tuner turns off when S-Video, Composite.
  -------------------------------------------------------------------------------
  30/09/2005, version: 1.0.2.4
  Bugs fixed and new features:
  1.agent.exe update for repeat bug!
  2.TI5150 sign up to fix video Format!
  -------------------------------------------------------------------------------
  2005-09-29, version: 1.0.2.3
  Bugs fixed and new features:
  1.A pilot of the trial build for multiple access medium. (in the folder "\Multi-Access")
  Note: The filter 'Audio device USB' provided by the system does not support mutil-access.
  2 reset TI5150 when a new frequency is defined
  -------------------------------------------------------------------------------
  2005-09-27, version: 1.0.2.2
  Bugs fixed and new features:
  1. difficulty I2C unstable access on some devices.
  -------------------------------------------------------------------------------
  2005-09-23, version: 1.0.2.1
  Bugs fixed and new features:
  1. analog TV becomes sometimes darker.
  -------------------------------------------------------------------------------
  15/09/2005, version: 1.0.2.0
  Bugs fixed and new features:
  1. difficulty of installation INF for Windows 2000.
  2 FM scan radio policy changed!
  -------------------------------------------------------------------------------
  13/09/2005, version: 1.0.1.9
  Bugs fixed and new features:
  1 USB string serial number not visible with USBView, updated firmware required.
  2. political analysis of FM radio, return of release if PLLOffset > = 9 x 12. 5 kHz
  -------------------------------------------------------------------------------
  13/09/2005, version: 1.0.1.8
  Bugs fixed and new features:
  1. after the passage between AV/D/A several times, video display becomes dark in THDTV 2.61
  -------------------------------------------------------------------------------
  12/09/2005, version: 1.0.1.7
  Bugs fixed and new features:
  1. improve the performance of check channel lock status
  2 pinnacle INF Fix.
  -------------------------------------------------------------------------------
  2005-09-09, version: 1.0.1.6
  Bugs fixed and new features:
  1. Add an audio initialization function.
  -------------------------------------------------------------------------------
  2005-08-31, version: 1.0.1.5
  Bugs fixed and new features:
  1 separation of PAL and NTSC resolution mode.
  -------------------------------------------------------------------------------
  2005-08-30, version: 1.0.1.4
  Bugs fixed and new features:
  1.AvgTimePerFrame.
  2 frame drop.
  3 pinnacle inf file HCT chkinf fail.
  -------------------------------------------------------------------------------
  2005-08-22, version: version 1.0.1.3
  Bugs fixed and new features:
  1. add remote control interface in digital source filter.
  2.A new remote test tool that contains of the source code in \Test_RC.
  -------------------------------------------------------------------------------
  2005-08-16, version: 1.0.1.2
  Bugs fixed and new features:
  1. Pinnacel & Twinhan driver & file reorg.
  2.VP704A_BDA_Test tool, add a test to the system code.
  3. set the standard infrared protocol of "IRSTANDARD", "IRSYSCODECHECK1" registry keys in the INF file.
  4 firmware update
  -------------------------------------------------------------------------------
  2005-08-15, version: 1.0.1.1
  Bugs fixed and new features:
  1 serial number feature is lost when the audio volume of the TV control
  2.RC6A support CIR
  (This firmware uses GPIO3 (M9207 pin 80) to decode the RC6 Protocol.
  The material must be reworked to connect the M9207 80 pin to the CIR module and the actual
  EEPROM must be flashed with \Firmware\M9207.bin)
  3 Serieal, MAC address and name of device OEM taken in charge.
  Please see for more details on the \Firmware\readme.txt.
  4 Ioclt example source code included.
  -------------------------------------------------------------------------------
  08/08/2005, version: 1.0.0.10
  Bugs fixed and new features:
  1. increase audio volume analog TV.
  -------------------------------------------------------------------------------
  04/08/2005, version: 1.0.0.9
  Bugs fixed and new features:
  1. analog TV Video mode failed.
  -------------------------------------------------------------------------------
  2005-08-03, version: 1.0.0.8
  Bugs fixed and new features:
  1.off - centerf frequency scan + / 125Khz
  2 difficulty program a copy scanned in MCE.
  -------------------------------------------------------------------------------
  02/08/2005, version: 1.0.0.7
  Bugs fixed and new features:
  1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' bug
  -------------------------------------------------------------------------------
  2005-07-28, version: 1.0.0.6
  Bugs fixed and new features:
  1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' support
  2. improve the stability of I2C communication.
  3 unify signaling resistance & quality as a THBda ioctl interface.
  4 capture filter lock state control.
  -------------------------------------------------------------------------------
  2005-07-28, version: 1.0.0.5
  Bugs fixed and new features:
  1. the same strength & quality signals as VP7046.
  2 debug build pilot
  -------------------------------------------------------------------------------
  2005-07-21, version: 1.0.0.4
  Bugs fixed and new features:
  1. put the INF update.
  -------------------------------------------------------------------------------
  2005-07-20, version: 1.0.0.3
  Bugs fixed and new features:
  1 improve performance in PCM4
  2 passage of the analog TV Mode to FM Mode failure
  -------------------------------------------------------------------------------
  2005-07-04, version: 1.0.0.2
  Bugs fixed and new features:
  1. production tool FM test OK!
  --------------------------------------------

  And here is the Readme file from the other file in the update?

  ************************************************** ************************************************
  ULi PCI to USB Enhanced Host Controller Driver V1.72 for Windows 98 SE, Windows ME, Windows 2000 and Windows XP
  ************************************************** ************************************************

  ----------------
  INTRODUCTION
  ----------------

  This driver supports the host EHCI ULi controller under Windows 98 SE, Windows ME, Windows 2000
  and Windows XP.

  -------------------------
  CONTENTS OF THIS DOCUMENT
  -------------------------

  1. installation instructions
  2. uninstall instructions

  ----------------------------
  1. installation instructions
  ----------------------------

  (Windows 98SE & Windows ME)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver files in your Windows system, and then restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver files to your Windows system, then turn off your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  (Windows 2000)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will install and load the driver and you do not have to restart the
  computer.
  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver in your Windows system files, before turning itself off
  your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  (Windows XP)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -Click "NEXT".
  -This program will install and load the driver and you do not have to restart the
  computer.
  -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
  Hub. " Please select "Install the software automatically (recommended)" and then
  Click 'Next' to continue the installation.
  -This program will install and load the driver and you do not have to restart the
  computer.
  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver in your Windows system files, before turning itself off
  your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller', proceed with the installation.
  -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
  Hub. " Please select "Install the software automatically (recommended)" and then
  Click 'Next' to continue the installation.

  Notice:
  If you can not configure driver successfully. Please restart your system, then follow
  steps to reinstall driver above.

  ------------------------------
  2. uninstall instructions
  ------------------------------

  1. open the "Control Panel" folder.
  2 call the "Add/Remove Programs" icon
  3 choose the "ULi USB2.0 Driver" section.
  4. click on the "add/delete" button to remove drivers.

  -----------------------------------
  Change list:
  -----------------------------------
  1.74
  1 fix this multi-interface keyboard may not be detected on the USB 2.0 hub.
  2. support all USB2.0 Host Controller.
  1.73
  1 problem on Win98SE, blue screen when you unplug a USB 2.0 Scanner after scanning image.
  2 solve problem on Win98SE, blue screen when you unplug a few Scanner USB 2.0 USB 2.0 Hub after scanning image.
  3 fix on Win98SE, blue screen when copying of files through the hub of UH-204 SUNBOX.
  4 solve problem as wirless lan will disconect when the plug in usb device.

  1.72
  1 fix that system crash when HD USB copy large files.

  1.71
  1. improve the management of power in Win98 / Me.

  1.70
  1. improve the devcie detection function.

  1.62
  1 solve the problem that can not operate a USB HUB USB 2.0 disk when the system resume inactive.

  1.61
  1 solve the problem that some device under USB 2.0 HUB is not found if resumes suspension system.

  1.60
  1. in support of functions power management when a HUB with the USB plug in device
  a root HUB.

  1.57
  1. Fix USB with USB 2.0 HUB floppy cannot detect problem.
  2. fix audio problem that can not display smooth when peripheral USB connect to the system.
  3. fix system cannot detect DVICE USB when the USB device attached to the system in
  suspend mode.
  4 fix when root USB HUB have a full load, USB HD sometimes
  failure of the transaction.

  1.56
  1 fix that device of DVD decoder cannot display correctly.

  1.55
  1. fix OTI USB 2.0 drive hand cannot detect question.
  2. attach the USB mouse cannot be used after the resumption of hanging.

  1.54
  1. to improve the safety of the driver.

  1.53
  1. transfer bulk fix may stop if the USB device is connected to the USB 2.0 hub
  2 difficulty USB 2.0 mass storage device cannot access after the release of the standby mode if there is an another USB 1.1 existing device

  1.52
  1 correct fault of system pages when accessing the storage of mass Win98SE or scandisk device failure when selecting
  automatically fix file system errors
  2. fix system may hang on in Win98SE / ME if USB 2.0 cardbus card is plugged

  v.1.51
  1. to improve the compatibility of USB 2.0 card reader.
  2. fix USB IDE devices are not accessible after the release of the standby/hibernation mode.

  v1.50
  1. improve the transfer block

  v1.48
  1. difficulty of installation of the USB 2.0 LAN driver hangs up
  2. attach a USB 1.1 card reader cannot be identified when plugged into the USB 2.0 hub
  3. fix some laptops starting hanging Win98SE

  v1.47
  1. improve the performance of bulk transfer.
  2. fix the failure of USB 2.0 Preview in bulk webcam.

  v1.46
  1. support USB 2.0 and 1.1 devices isochronous
  2. fix system hang up when restarting system if the USB 2.0 host controller is disabled in Win9X / ME
  3. fix system hang up when you uninstall the driver if there is USB 2.0 connected under Win2K/XP devices
  4. improve the capacity of the device detection in Win9X / ME

  v1.45
  1. fix system hang up when the mode standby ACPI.
  2. attach the mouse sometimes does not disappear when it is unplugged.
  3. fix the failure of detection of composite devices Win9X and improve device composite Win2K/XP

  v1.44
  1. composite crutch
  2 improve the detection of devices

  v1.43
  1 improve the failure rate of transfer IDE read/write with USB 2.0 to IDE bridge on the platform of PC card
  2 difficulty at high peripheral speed detected as full-speed device
  3. fix some problem of failure detection USB mouses
  4. fix some problem USB 2.0 Hub failure detection
  5 difficulty Win98SE crashing if ULi EHCI 1.42 is installed

  v1.42
  1. fix PC Card eject hang up in Win98 / ME
  2 difficulty of interruption/resumption hang up in Win98
  3 sometimes solve USB 1.1 device cannot be detected if OS starts with USB 2.0 and 1.1 devices plugged
  4. fix some failure detection of PC Card USB 1.1 devices

  v1.41
  1. Add new feature that system can install the driver ahead of the device is plugged in.
  2. fix PCMCIA OHCI controller resources affect problem on Windos ME.

  v1.40
  1. support Win9X/ME / 2 K/XP with ULi USB 2.0 driver.
  2 fix PCMCIA EHCI controller detection device USB 2.0 problem in Win9X / me.

  v1.32
  1. Fix problem that pilot cannot detect the Microsoft driver in Windows XP
  If the path of the OS is not c:\windows.
  2. Fix problem that pilot cannot detect the USB 2.0 controller device in a system.

  v1.31
  1. Fix problem that driver cannot install on Windows 2000.

  v1.30
  1 fix than Win9X / shows ME no USB 2.0 hub.
  2 solve the problem that hang up when the second entry in Win9X S1 with HID device connected.
  3 Fix problem that sometimes when you click on "search the hardware changes.
  for PNP ULi USB2.0, controller, the system will inform you the usbehci.sys
  file is not found.
  4. Fix problem that v1.20 can't find no EHCI controller to install the driver for after different
  verison of ULi EHCI controllers devices are connected and disconnected.
  5 install the driver support for several features of controller EHCI ULi existing on
  system at the same time.
  6. determine Win2K/XP shows hub USB root for USB 2.0 hub.

  v1.20
  1. support ULi USB 2.0 for Windows 98SE/ME/2000/XP host controller driver.

  ULi Coporation. (ULi) web sites:
  http://www.Uli.com.tw/ (Taiwan)

  CAN SOMEONE TREAT ME LIKE A CHILD OF TWO YEARS AND GIVE SOME ADVICE AS TO HOW TO OBTAIN THIS UPDATE.

  I'D VERY GRATEFULL AND KIND OF THINK IT would BE BENEFICIAL to a LOT MORE than PEOPLE LIKE I SEE a LOT OF XP AND PROBLEMS OF THE KIND THIS UPDATE IS SUPPOSE to FIX.

  It is said above 2 relevant and 1 right ANSWER available...

  I'm new here, so anyone could direct me to these answers?

• USB and DVD not recognize anything it shows that peripheral unknown.

  Original title: USD/DVD does not work.

  my USB and DVD does not recognize anything, it shows device unknown and does not work.

  Hi alexandrebernat,

  You did it all change hardware or software on your computer before this problem?

  For the question USB, you can follow this link & check if it helps.

  USB port may stop working after you remove or insert a USB device

  Reference: Troubleshooting tips advanced to General problems USB in Windows XP

  For the CD/DVD drive problem, you can follow this & check if it helps.

  Your CD or DVD drive cannot read or write media

  Reference: How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD

  Hope the helps of information.
  Please post back and we do know.

• HP 8150 printer does not print error: Re-installing the printer, unplug the USB and power and re-boot do not solve the problem

  Original title: hade 8150 printer does not print

  Under Vista Home Premium with all updates. The printer is a Photosmart 8150 H - P, which worked well for a few years. Now, when you send a document, for example, a Test page and looking at the queue, I immediately get an error. Re-installing the printer, unplug the USB and power and re-boot do not solve the problem. Grateful for any ideas. Thank you

  Hello

  (a) don't you make changes to the computer until the problem occurred?

  (b) when was the last time it was working fine?

  (c) you use a network printer or local?

  I suggest you try the steps below and check if it helps

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope this information is helpful

• Problem USB with Satellite P100-219

  I have problem with USB on my Toshiba. USB peripheral Al are working except memory usb and external hard drive. USB and hard are OK. When I connect to them it says device not recognized USB. I have win 7 ultimate, but I also try XP and it does not work on XP or Win7.

  Can it be related BIOS. BIOS is Phoenix 4.80, Toshiba support was last updated. Motherboard drivers are also updated. But I don't see any fucntion USB in the BIOS?

  Someone has an idea? (all common as uninstalling the drivers or similar metodhs are already done)

  THX in advance

  Tom

  Hey,.

  Load default settings in the BIOS after update BIOS?

  In your case, I would also try updating the chipset driver. You can find the newest one on the official page of Toshiba:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

• After hybernation, all usb and wifi mobile devices does not work

  Original title: Hybernation question
  After hybernation, all usb and wifi mobile devices does not work. Similarly, it is not stop as well. I turn off the power to the network option all usb hubs. Problem however still closes. Please suggest. I have Windows XP Sp3 installed. All the drivers and the windows update is up to date.

  Hi Mirza.Shanawazbaig,

  1. what happens when you connect any USB device to the computer, or trying to shut down the computer after hibernation?

  2. do you have security software installed on the computer?

  3. did you of recent changes on the computer?

  4 when was the last time it was working fine?

  Method 1

  See the below Microsoft article and try the steps mentioned, check if it helps.

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  http://support.Microsoft.com/kb/871233

  Method 2

  I suggest that you download and install the updated driver for the network adapters and display on the computer by visiting the card manufacturer or computer manufacturer website manually.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

• USB and drive not recognised on a Mac SuperDrive

  I'm under VMWare Fusion 3.02 with Snow Leopard 10.6.2 as my host and XP as my guest.  When the virtual machine is turned off, I can use connections USB and drive SuperDrive on my Mac without problem.  However, when the virtual machine is on I can't get the host to either recognize but they work under XP.  Is there a way to fix this?

  Thank you!

  In Fusion, Virtual Machine, USB.  Click on "disconnect...". "on each item that you want to stop using in the virtual machine.

  To have the VM not automatically 'catch' a USB specific peripheral (s), in the settings, USB for the virtual computer, uncheck the box or devices.

  Do you similar for the Superdrive, which is registered as a CD/DVD in the Fusion menus and settings.

• Problem USB 2.0 on Satellite P200-1JR

  I bought my laptop about a month ago, and yesterday I tried to use my flash drive.
  After noticing that he took too long to transfer data, I checked the usb ports in Device Manager.
  It shows that I have five simple USB and two USB 2.0 host controllers.
  Changing the display 'view of the connections' I realized that my 6 USB ports share three of five simple USB controllers.

  The laptop is supposed to offer 6-Port USB2.0... well, it doesn't.
  (Also under Vista 32-bit, with 3 GB of Ram)

  The service guy told me to format, but this does not solve anything.
  I also got BIOS 2.30...

  Any ideas?

  Post edited by: kostas_kompostas

  GMC

  have you tried to reinstall the chipset drivers? You may need to check www.intel.com and download the latest chipset drivers for your machine.

  Another suggestion is to check that the sites of microsoft support for USB problems since Vista is known to work intestinal and I guess that there must be something on USB to find...

  Welcome them

• HP 50 g - PC connection series with adapter Series USB and null modem troubleshooting

  I have the calculator correctly connected to my laptop via a USB series adapter, which is plugged into a null-modem adapter, which is plugged into the serial cable sold on HP Calc.org specifically for the HP 50 g. I started XModem on the calculator, but Conn4x found nothing. Is the process different from that used for USB and Conn4x connections? The problem could be with the USB Serial Driver. I use the default MicroSoft driver installed to connect? Are there tests I can run to determine if the adapter is broken, or the computer or calculator. Thank you very much in advance for your help!

  I already tried the following:

  • The two indicators relevant system are correct for the serial communication
  • Tried to reinstall the driver
  • Google for any relevant information that is extremely rare
  • Tried with two Xmodem Kermit servers running on the calculator, press 'Connect' on Conn4X.

  Hi!, Ranothil:

  If you have the following cable "null modem" (http://commerce.hpcalc.org/serialcable.php), you can transfer, all

  data, HP50G, to the PC and vice versa, throughout the connection Kit (Conn4x), without issue.

  Please, see this link, to education, to transfer data with the serial null modem and connectivity kit cable... http://sense.NET/~Egan/SKB/ or... http://www.hpmuseum.org/cgi-sys/CGIwrap/hpmuseum/archv017.cgi?read=125259

  Note: best if you transfer data, HP50G, PC and vice versa, through the microUSB.

• I found the solution for the problem of sound-acpi with Satellite P100-219

  Hello

  I found the solution for the problem of sound-acpi with Toshiba P100 (it works with P100-219 at least). I can provide the source modified and compiled table DSDT, but I would like to know if it is possible to get these changes in the next update of the BIOS?

  See you soon,.
  MIK

  Hi Mik

  As you know that it is not possible to find info on the next BIOS, especially if you want to have some information about the Linux operating system. Just wait and see if some forum users pointed out something on the subject.

• Windows failed to update for HP - Bus USB and Ports, display controllers - HP w2408 widescreen LCD

  I have a new HP M9402 desktop with monitor Hp W2408 Summit.  I get a message to update windows for HP - Bus USB and Ports, display controllers - ACL from HP w2408 widescreen, but the windows download always fails.  I tried several times to download this update.

  Any help would be greatly appreciated.

  Hi all

  The solution to my problem of not being able to make updates to the window was to spend in an HDMI instead of VGA cable.

  BR / / JJG

• Satellite P10: Controller USB and IEEE 1394 do not work after WXP re - install

  Does anyone know how to fix this problem?

  I recently reinstalled WXP home on my satellite p10 computer laptop and then installed all drivers and utilities from the support CD that follows with Notepad.

  Everything works except for USB and Firewire.
  Very strange screen system shows me that I have bad driver for usb controller, but when I run the utility chipset problem remains. I even downloaded the drivers on the Toshiba support home page in the hope that it would be a different version and they would work, but nada... same problem persists.

  Someone knows how to solve this problem, or what is suitable driver for the controller USB on satellite p10 554 and where can I find this driver (without the entire chipset utility?)

  Thank you in advance for your help!
  David

  Hello

  the funny thing is that USB is IN the chipset. The problem is that you can extract some drivers you need, given that utilities chipset intel are a complete set.

  So, I suggest you go to the website of intel (www.intel.com) and then download the chipset utility. Don t forget to update your windows (Service pack, updates, bugfixes) because the operating system has sometimes problems with the hardware installed, then an update will solve this...

  I hope that you have little luck with the original software of the chipset intel.
  Give a few comments after completing the makings and let us know if it worked.

  Good bye

• Y560 Problem USB

  Since I formatted, o of the 2 right (SATA/USB and the USB port) USB does not work. It is powered, it can turn on my stand fan, but it will not read USB Flash drives, external hard drives or power my mouse. What's wrong? The other two on the left side works fine

  I solved my problem, but the disadvantage is that I have practically re-installed Windows 7 Home Premium. All my files were left untouched, although the installation took most of the day, but it worked for me.

  What I've done and what I would say, it's getting a DVD of images from here and burn (make sure to get the right one):
  http://www.PCWorld.com/article/248995/how_to_install_windows_7_without_the_disc.html

  Download/install Win7 SP1 to match the DVD image links in the previous link. Basically, the disk you install must match what is currently installed on the hard disk.

  Follow this guide: the exploitation of a repair installation (in fact an 'upgrade' to the same version, but he rewrote all of the important system files, keep your data in tact):
  http://www.PCWorld.com/article/243190-2/how_to_repair_a_corrupt_windows_7_installation.html

  It is a long process, but it worked for me. I tried the new chipset drivers, etc and nothing worked before that. Good luck to everyone who has this problem.

  -Dave

• Insulator usb and GPIB-USB-HS

  Hi all!

  I'm trying to control a range of aglient with a labview program.

  everything works well, but for my application the scope must be one reason other than the computer.

  so I bought a usb isolator: http://www.bb-europe.com/product_family.asp?FamilyId=651

  but when I plug the reach through it, it is no longer recognized by windows. If I plug the GPIB-USB-HS only, it is not recognized nor.

  GPIB standard speed is 1.8Mbits / s, so I chose the UH401SL (low speed), and the GPIB-USB-HS is compatible with USB 1.x, so for me it is not a problem of transfer speed...

  any ideas?

  THX

  Power would have been a problem, but the speed was probably just as well. The GPIB-USB-HS is designed for USB 2.0 high speed, but also works with USB 1.1 Full Speed(12 Mbits/s). It is not designed to work with USB Low Speed, because most computers with USB implemented USB 1.1 or later. It is virtually impossible to find a USB port that does not support Full-Speed at, but apparently this insulator is an exception. Low speed is usually reserved for devices with needs bandwidth close to zero, as keyboards.

  I must also point out that the maximum speed of the GPIB-USB-HS is 1.8 MB/s, which is of 14.4 Mbps, before taking into account overhead Protocol USB or traffic from other USB devices on the system. This puts a little above the capabilities of Full-Speed USB, and much more than can be supported with USB low-speed.

  -Jason S.