port bug console virtual iDrac 2.21.21.21

Similar Questions

• Mapping to Com Port to a Virtual Machine

  Hello

  How can I map a standard com port to a virtual machine. The reason behind this is that I will be remote access to a virtual machine that is on an esxi host who has a com port so that I can configure my router.

  Kind regards!

  You need just a serial port available on the virtual machine for this? If so, you can add a serial port (connect via the network) for the virtual machine hardware.

  ... or do you have the router connected to the serial port of the host and must enable passthrough for this?

• Need help to add serial port to a virtual with "Output to the file" computer in PowerCLI

  I have a requirement where I have to add a serial port to a virtual computer that is an Ubuntu operating system and the port type must be 'output to the file"with a file name specified in a data store on the same ESX host.

  Can anyone provide me with a script of powerCLI for this please?

  Thank you very much

  Suparna

  I advise you to upgrade to 4.1 PowerCLI.

  If this is not possible use the attached script that works for versions pre-version 4.1 PowerCLI.

  ____________

  Blog: LucD notes

  Twitter: lucd22

• Console virtual not availabe on R320 with iDRAC7 Ent.

  Hi all

  I recently implemented a new server Dell R320 and when I login iDRAC I don't see the live preview of the virtual console.

  There is only a message saying ""session VNC being active, Virtual Console is disabled. " "

  Same thing if I go into the menu of the tree and select 'Virtual Console '.

  Welcome any help to solve this problem.

  Thank you in advance.

  Kind regards

  

  Stamatis.T,

  IDrac allows a VNC session or a session of Virtual Console at some point, but that a single VNC session is permitted at any time. The Virtual Media feature is available in two types of session, but if a VNC session is active, you can only run the virtual media using the Virtual Console launch and not the Viewer for Virtual Console, as you see with the error you get. I would like to know if this is the case, also try disabling the VNC, as shown below and see if the Virtual Console is accessible.

  

• Access to the BlackBerry through the USB port on the virtual machine VMWare

  I have my development environment configuration in VMWare virtual machine, and I have no problems of deployment of BlackBerry applications on a simulator that runs as another virtual machine. The problem starts when I try deploying to the device via the USB port. The address is assigned when the mode of development on the device is not accessible from the VM, but only from my host, who do me any good, since as I said my IDE is in the virtual machine. A way to solve this problem? I can still deploy to the device via wi - fi (which is btw access via different ip - one given by the network) by this can sometimes be slow depending on the strength of the signal, etc, so I prefer to be able to deploy via the USB port.

  Just in case anyone has the same problem, how to activate must, VMWare Player click on the USB icon (to the right) and choose to disconnect from the host. Connecting the USB port at the prompt. Stupid...

• 'Fail forward' for Ports on the virtual machine

  We have a customer who will be centralizing the unit with about 250 users at remote sites (4 Sites, 1000 Subscribers, they have currently a unit break at each site and want to centralize). Each site will have its own cluster of CM. I'm thinking about what I could do failure network SCOPE. Of course, each site will be fine IPT wise because they have their own cluster of CM, but VM will be declining. I think I watered but if there was a way to "transmit failure" or something on the VM ports on the PSTN to maintain the work of the virtual machine. (Of course carrier must support ISDB).

  Someone at - it works in this or thought about it?

  Andrew Dignan... If the carrier supports RDINS of course

  The connectivity of voice mail for Cisco CallManager chapter of the Cisco CallManager System Guide:

  "Inter-classes Interfaces A Cisco CallManager in a cluster can provide access to a voice mail system in another cluster, if the administrator provides the voicemail number on the trunk driver inter-classes. Voicemail systems can leave messages and sets the flags of message waiting for devices other clusters if clusters are connected by trunks QSIG. »

  This applies to any system of virtual machine. With the unit, you have of additional capacity to save ports across multiple clusters so to provide MWI without ICTS as QSIG.

  Hope this helps,

  Eric

• Only use the Thunderbolt port in the virtual Windows machine

  Hello world!

  I'm running a Macbook pro with a Win OSX 7 VM to work - we are currently on a split network when you access WWW on Wifi and undertaken by Ethernet through the thunderbolt connection.

  When you plug the cable Thunderbolt in, it disables our Wifi (so that we can fill the Wifi and the access of the company)

  Is it not possible to set up the computer so that the Thunderbolt port is only seen in the virtual machine (Windows) and OSX using the wifi only?

  That would mean I could have two separate work stations, an OSX with WWW access and Windows with business access, which would be extremely useful?

  I lived the preferences, but as soon as I disable the Thunderbolt OSX port it disables it on Windows as well!

  Any help gratefully received!

  You can do all this, I do it all day long.

  On the Mac, the "top" of your list interface is considered to be the main route of access and the host will forward the traffic it is there until he can't, and he then tries other interfaces.

  So, just to pay for the order of Service so that your WiFi is at the top.

  Then you can use the merger to specify the Thunderbolt interface to fill in.

  This allows Windows to use the bolt of lightning, and the Mac continues to use the WiFi.

  You an also save the config in a 'location', which are accessible from the Apple menu to quickly switch between configs. (i.e. specific vs)

  OS X Yosemite: change the priority of your network connections

  http://www.tekrevue.com/Tip/network-interface-service-order-OS-x/

• Client console virtual trava ao access!

  Pessoal.

  Sempre tento o Access console of any VM ela seja windows or linux client o virtual trava e nao responde but a tela console fica preta sempre, ai I have that can e ele logo depois ocorre aquela tela enviar Relatório para Microsoft. O o tem micro XP 1 GB memoria PIV com.

  O that pode ser? JA it happened com alguem isto?

  FLW...

  Well, as erro feio.    8V)

  Best remover o vSphere Client e E e .NET Framework dessa Máquina o restore Doi - com um preferencia os download bem updated. E instalar um user than admin seja using local desse Windows.

  Com 1 GB XP roda o customer direitinho, deve ser any coisa ai nessa did. O VI Client tem connects, to Saber realmente quiser o esta wrong, mas geralmente reinstalls um mata.

  [VM made to the Brazil |] http://communities.vmware.com/blogs/aandriolli]

  PS: Please consider dar pontos has este or any poster caso seja util lhe outro.

• For consoles Virtual Center and VM user level access

  All,

  Is it possible to provide a user with access to the virtual Center and don't have rights to access a particular SMV console... ??

  This is because the server is in a DMZ and no network management is provided.

  Any suggestions are welcome.

  Nels

  You use VMware permission.

  First to create Windows user (may be a local user on VC or a user AD).

  Then on your virtual machine (in the authorization tab) add a role (e.g. VM user).

  More info on:

  http://www.VMware.com/PDF/vi3_vc_roles.PDF

  http://www.Petri.co.il/VMware-ESX-roles-permissions-privileges.htm

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• Lost service port IP console

  Hi all

  I had to prepare a new site of the PRD, who should not be on our range of intellectual property. Everything worked fine with my service with a fixed IP console and I had no problem (link with a card, 4 ion total entwork). But unfortunately, I first create a VMkernel port with the different range of IP addresses and I add this new vswitch on the same network adapter and then I lost all link. I got 4 comments on this vm and evrything works but how do I do to get the good IP on the management console (ESXi)?

  Please help as I have on-site engineer within 2 days for the installation of DOUBLE take.

  See you soon

  esxcfg-vswif is your service console command. Something like:

  esxcfg-vswif - a console service Pei-i x.x.x.x-x.x.x.x - n

  -an add Pei port set group name,-i = ip address you want to use the network mask - n for your network.

  just enter esxcfg-vswif no options will show you all available commands.

  See also http://www.rtfm-ed.co.uk/docs/vmwdocs/ESX3.x-VC2.x-ServiceConsole-Guide.pdf

  page 23, you recreate your vswif0 interface

• Blocking ports using a virtual Super Hub 2ac (VMDG490) machine

  Hi all

  My first post and hoping that it is in the right place. A few days ago, I received my upgrade to a SHub1 to SHub2ac. After a speed problem. I created 4 blocking rules port for one of my computers successfully, but when I try to create the same blocks for my other computer I get an error of "the port selected range overlaps with an existing rule".

  I gave the rule a new name and have obviously used the ip addresses of the other boxes on the network. It worked well on my old SH1 then why not on an alleged update?

  VM, I called and they had no idea if it was possible and showed me tech, alas, they had no idea that is then reported to me their salary for support Dept. They said it couldn't be done? As a Department tech VM and the pay per help guys were unable to offer advice, other than to block ports through your firewall software. Can be done using Bitdefender, I can see (it's another can of worms in itself).

  Any help or advice of Netgear technicians or other users of the popular home network. As seems a downgrade of the former 1 SuperHub that would allow any amount of blocks of port by using port numbers providing the name of the rule was different and the IP addy has been changed, is there a possibility of a upgrde of firmware to re - enable this option? Or the guys from VM need to RTFM

  Any help is much appreciated in this matter.

  Best regards.

  Fubar

  sent you a PM response

• Multi monitor mouse bug with virtual display

  In my computer (8.0.4 build-744019), if you have several configured monitors and then dynamically add another exhibition, the location of the mouse real discrepancy between the mouse cursor for screens other than the first screen.  This has been a problem for some time and it seems there's always a problem.  I used several tools for this in the past, all with the same results.  Currently I am the do with REDFLY ScreenSlider which allows me to use my android as a monitor via wifi device.  When I connect with the new monitor on the right of the other monitors (all are aligned at the top), it works fine.  However, the mouse is shifted a little on all, but left the larger screen.  Something like a few hundred pixels.

  Of course, this looks like a bug so I reported.  I'm hoping someone VMWare could confirm this as a problem and give me an idea of if / when it will be fixed.

  Have you tried to put the Edit\Preferences\Input to "Optimize the mouse for games" = always?

• VMWare Workstation bug in virtual Windows 7/Windows 8 (glitches).

  I have the black seeds on my virtual office.

  Is anyone know the solution, how to fix?

  Relocation of the comments system has not helped.

  Video card drivers reinstall also did not help.

  VMWare Workstation 8.0.3 build-703057; Speed up graphics 3d - active

  Host system: Windows 7 x 64, 8 GB of RAM, video of NVIDIA GTX 580 card 2 GB (301.32 nvidia driver)

  Comments system: Windows 7 x 86, 2 GB of RAM.

  Nothing in the changelog for the release of the pilot, but nvidia 301.42 WHQL drivers coming out seems to have made this problem go away for me on my GTX 680.

• How to access a host USB Virtual Serial Port from a VM Application?

  I have a Linux VM running under VMware Player 5.0.2 on a Linux host machine.   I have a development system running on the computer, virtual trying to download the code on an external device connected via a virtual serial port USB host (ttyACM0).   Anyone doing programming Arduino device will be familiar with my software/hardware config.  Dev VM system does not directly hear the ttyACM0 port I need to establish some sort of connection bridge between "ttyACM0" host port and the port of VM-configured "ttySx"?   Someone did something like this with a VM Player?

  FYI, I found the answer to my own question in an old post on a similar topic. Here's a response provided by the user 'Worker' in the former post office that was the solution to my problem.  I followed its general approach and mounted my own virtual *.vmx machine configuration file to change the serial port set of ' / dev/ttyS1 "to" / dev/ttyACM0 ' I can now download code on my device directly from the Arduino IDE running on the guest VM system.

  *************************************************************************************************************************************************************************************

  9 re: USB serial adapter - / dev/ttyUSB0 serial not a device?

  

  Worker (1 positions since November 23, 2010) November 23, 2010 12:56 am (in response to AnthonySowden)

  A bit of an old thread here, but I wanted to say that I was able to do exactly this yesterday using VMware Server 2.

  It wasn't easy, but I managed to hack in there.  I guess that this trick works also on VM WS but I have not yet tested.

  Here are the steps:

  Start your VM turned off.

  Add a serial port of your virtual machine through the normal interface. -J' I just let it use/dev/ttyS0.

  Go to your virtual machine folder and edit the .vmx config file.

  Find the line:

  Serial0.filename = ' / dev/ttyS0 ".

  Replace:

  Serial0.filename = "/ dev/ttyUSB0 '.

  and off you go.  The guest operating system sees it as a real physical serial port and is fortunately out my system through series console!

  Hope that helps other people.

  ************************************************************************************************************************************************************************************

• Virtual USB port

  I am trying to install an HP Laserjet 1012. My computer has Vista Home Premium. I downloaded the 64-bit driver for HP and the installation of the printer is connected to a generic IEEE printer port not USB virtual printer. The printer is very slow (20 to 25 seconds delay) between the command print and real output to the printer. It is a one-page letter. I can only imagine what a large document would be. Is there a solution to this problem? Thank you

  Hi Steven5361,

  Thank you for using the Microsoft Vista Community Forum.

  Sorry to be the bearer of bad news, but your printer is not compatible with Vista.

  Here is the Vista compatibility checker where you can check and make sure that any new material, that you look at is compatible.

  You can process just be slow, since he works at least!

  http://www.Microsoft.com/Windows/compatibility/details.aspx?type=hardware&p=LaserJet%201012%2015ppm%20600x600dpi%208MB%20USB&v=HP&UID=Q2461AABA&pf=0&PI=0&s=HP%20Laserjet%201012.&OS=32-bit

  Matt Hudson
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.