Port forwarding on WRT160N V2

Similar Questions

• Problem setting up Port Forwarding with two routers.

  I can't set up by Linksys RT31P2 and routers port forwarding WRT160Nv3.

  My setup is Webstar Modem = RT31P2 = WRT160N = Mac OS 10.6.5. (No configurable modem and ISP do not prevent port forwarding. It comes with two Linksys routers).

  I had a Monty Python-going around with the support of Cisco cat; and follow up with telephone assistance in which the agent knew nothing about port forwarding and his supervisor expressed the view that it was not possible with two routers. Sigh.

  If anyone can help me with step by step specific and simple instructions to configure routers. I know that the basic procedures. I'm not clear, what exactly changes on routers.

  I read that portforward.com has to say and it does not work so I must be misunderstanding something.

  The ip address of my computer is 192.168.1.103.  Are the last three digits of this speech concluded the two routers in the area on the port forwarding page? What other changes should be done what router?

  I know the port numbers that I use are OK because I can implement successfully if I connect to one or other of the routers (but not both), and my software of p2p shows port are open.

  Any help and suggestions most welcome.

  If you set up as I have suggested that you have only a single LAN that will be using in your addresses * 192.168.15 case. So in your case:

  1. change the address LAN IP of 192.168.1.1 to 192.168.15.2 WRT.
  2 disable the DHCP server.
  3. connect the LAN of the WRT port to port LAN of the RT.

  That's all. Disable the DHCP server will not affect whatever it is that you're connected LAN - LAN and DHCP server on the RT is still operational.

  After the change, previously the WRT computers may require a reboot to get a new address 192.168.15. *.

  Your computer to which you are transferring must have an IP static and not dynamic (or variable). Check the current IP information on this computer. It must have an IP address like 192.168.15.103, mask 255.255.255.0, gateway 192.168.15.1 subnet and DNS 192.168.15.1 server or maybe two other IP addresses instead. Note DNS servers if you do not 192.168.15.1.

  Then configure a static IP address on the computer. Use something like 192.168.15.10, 255.255.255.0 gateway 192.168.15.1 and the DNS servers you found before.

  After this implement 192.168.15.10 port forwarding.

• How can I enable port forwarding in the router of the time capsule

  Does anyone know how to enable port forwarding in router Time Capsule Airport please?

  Port Mapping on the time Capsule airport cannot be enabled unless you have the right type of modem on your network.

  Thus, we need the number of brand and model of the device you're calling your "modem" before we can move forward. Please post back this information.  We do not need a series number... only the name of the manufacturer and model number of the modem.

• Why isn't my port forwarding of the opening port

  I have the latest version of the 3 terabyte time capsule. I'm trying to forward a port so I can access my security cameras and it does not open.  My camera 100 port needs to be open and it will report as not open on any port test sites. Any ideas as to why, I use a static ip address of the server for the security system.

  Testing websites are useless... test by plugging actually to the camera from a device attached to a captive phone or a friend...

  Port forwarding works only if you have the public IP address on the Wan of the TC... and it's the only router in the network... is this the case?

• your external IP address for port forwarding

  OK, so I want to do a game server, but... There need Port Forwarding, so I called my InternetServiceProvider "Clear."

  Claire told me that "WE DO NOT support the external Ip addresses: then I was then told that I have to call HP because that's what my PC is under.

  I decided to go to the site and ask because they want a $ 60 million tax which is good, but... I don't have the money! This is why I need a server. In any case if you can please give me a video or tell me how do it in the response that would be LARGELY APPRECIATED!

  -Sincerely

  VladmirTodd

  Go to portforward.com and use their tutorials.

• Airport of Port Forwarding is more?

  So I'm pretty new to this network thing. I don't know the technical network terms then please do not use (or at least their simplification). So I managed to set up my ASUS RT - something something router. I also put in some rules to sink my Xbox One anywhere port forwarding. However, I had problems with port forwarding, so I just used the dmz for her service. However, given that I had to move my Xbox to another part of my house with worst network connection, set up a time capsule for the network. After a long time, I managed to do the work, but now I can listen to is no longer my Xbox. My guess is that the port forwarding rules are not carriers, as it connected via ethernet time capsule and the capsule is connected to another time capsule via radio and this time capsule is connected to my ASUS router via ethernet. So my question is: how to transfer the required ports to my Xbox?

  If both of your time Capsules are configured as bridges, the Asus router is the one that needs to be set up on port mapping. The port mapping is used only when a router is configured for routing. In other words, the NAT and DHCP services are enabled. This is the default value for any router.

  Just to make sure that I understand your current network configuration, the following is correct?

  • ASUS > Time Capsule > > > Time Capsule > Xbox, where ' > ' represents a wired connection, and ' > > > ' represents a wireless.

• How do I port forward on apple airport? (READ ALL)

  I have an airport express from apple connected to an asus router via wifi and I need to know how I can portforward by airport to the router because my pc is connected by ethernet to the airport. Help, please.

  The express should be none not routing at all and therefore no port forwarding.

  The only way this can work is the express installation to the wireless bridge... Apple called client mode... There is no routing.

  BUT it can also have port problems... It is really unsuitable if you operate in questions.

  In any case all the transfer is possible on the Asus.

• Port forwarding rules missing WNR1000V3

  I read a few posts here that may be similar, but they are so old, that threads are blocked. I'm trying to help out a local company add some rules to redirect to their server port WNR1000V3 more.

  They must have some configuration of port forwarding already because they are able to access an existing via RDP server so there is a rule somewhere for port 3389. However, it is has nothing listed in respect of port forwarding.

  My view on it after scratching my head for several hours, it's that there is either a port forwarding rules defined and running, but they are not displayed in the user interface, OR there is some screen that I have not found (was all!) where port forwarding is also configured.

  I think it's the first because there is no rule for the listed FTP, but if I try to add a new FTP rule, it displays a "conflict of Port with other services".

  Firmware is V1.0.2.62_60.0.87 although the router points out that there is an update.

  There is a known issue like this with this model? It seems a few years old.

  Thank you, Rob.

  Sorry, I would have given an update on that. I am aware of what means the error and it was probably that a rule on this port unless it was not displayed. I hoped that export Netgear configuration could be a human readable script (found on the Cisco routers), but it's not.

  After discussion about ServerFault and checking some of the suggestions there, it became clear that something was broken enough with the router. An update does not solve so I have taken note of all the settings and did a reset.

  That solved the problem. My theory is that some bugs in an earlier version of the firmware caused a bad record in order to be there for port forwarding. One that actually worked, but could not be displayed.

  Cheers, Rob.

• NETGEAR ProSafe VPN Firewall SRXN3205 and port forwarding?

  Hi, this is a long shot, but I'm pulling my hair out at this point and can be a bit over my head, as I am new on network

  Small short story, I have two servers, one is the NAS box (IE if I connect via the internet to the site via public IP network from home, I get it that site says 'my actions' I insert login and pass and get access to them.)
  That is, everything is peachy.
  The problem is when I try to connect to my FileMaker Server I'm not and instead, he takes me to the login NAS box. So I think ok, I need to port forward (5003 for filemaker) to go to different PC local LAN(192. etc)

  Security > firewall > Add Service entering:
  Service: fmserver
  Action: Always leave
  Send to LAN Server: unique address 192. etc is filemaker installed on (and different on a NAS)
  Definition of Port number: 5003<-- is="" this="" right?="" how="" else="" would="" you="" indicate="" you="" want="" all="" connections="" on="" this="" port="" to="" go="" to="" this="" specific="" lan="" machine="" from="" internet="" instead="" of="" default="" which="" seems="" to="" be="">
  rest is default, I click on apply.

  Here's what I don't understand. In the table of incoming Services, (security > firewall) I have two local IP in the list, a SIN, the other for Filemaker. But only the top works and can be connected to. I can move every top position and it will work, but they will not work at the same time, just the one that sits on the top of the sad Smiley page

  and yes I read the manual again and again and don't know how I'm screwing up the port forwarding on this point, even if I am brand new to probably something stupid Smiley Happy (our work IT guy is gone so tried to get involved through this somehow)

  Any help would be appreciated.

  Hello sinieq,

  There is a hierarchy on incoming service table, which is normal. I see 4 services added using "ANY" (ALL use any port number) you will need to remove/disable these because of the rule of the hierarchy on the table, all other services will be ignored when EVERYTHING is used. What is the port number used by the NAS Server? I don't see a port defined to access NAS. Try disabling services by using "ANY" and try again by adding the translation to the port number of the NAS.

  Let us know what happens.

  Thank you

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• UDP Port forwarding

  I opened the ports on my Airport for HTTP, TCP, and UDP.

  By using the website canyouseeme, I confirmed that the TCP and HTTP ports are open.

  However, the UDP port is indicating 'connection refused '.

  Port forwarding is configured to be the same for each.

  Any thoughts would be appreciated...

  I opened the ports on my Airport for HTTP, TCP, and UDP

  FWIW, only the HTTP protocol is a 'standard' port already assigned. It is port 80. This port can be a type TCP or UDP port. On the other hand, generally TCP or UDP ports vary from 0 to 65535... so your statement «I open ports on my Airport...» TCP and UDP"does not tell us what are the ports really tried to open and for what reason.

  Some ports are blocked by ISPS, so this may be a reason that the method used, canyouseeme, can not 'see' she also open.

  Is your 802.11ac AirPort Extreme router "main"? In other words, it is directly connected to a simple Internet modem via an Ethernet connection between them?

• Router not configured for port forwarding

  I use a modem wireless to my ISP, they block all ports less than 1024 and I need to forward ports 80 & 440

  How can I solve this?

  If you configure your router for a LenovoEMC Personal Cloud and always see the message, "Not configured router for port forwarding" under personal cloud Configuration, one or more of the following ports are probably blocked by your internet provider (ISP): 80, 443or port selected in the range 50500-50599 .

  Port 80 is used for internet access (HTML UN-secure) in general. If this port is blocked, but the ports 443 and 50500 are open, the Personal Cloud will work correctly even if the error message appears.

  Port 443 is used for remote access on the host network storage device. If this port is blocked, but the port selected in the range 50500 is open, you will be able to use the Personal Cloud LenovoEMC and invite others to use it, but you will not be able to access your network storage device via the Internet URL. (See answer ID 30773 for more information on access remotely through Personal Cloud LenovoEMC.)

  A port in the range of 50500-50599 must be routed through the router to use the function LenovoEMC Personal Cloud. If this port is blocked by your ISP, you will not be able to access the Personal Cloud to your network storage device or invite others to join the Personal Cloud. (For more information, see answer ID 29070 .)

• Port forwarding on Time Capsule for Geniego

  Anyone know how to configure the port forwarding on time capsule?

  I need to set a port 8082 & 8083 for my Directv Geniego.

  Press the bar area and order at the same time.

  Airport utility type, press ENTER.

  Select time capsule, and then select edit (enter the code for the device).

  Select network, select "+" sign

  Firewall entry type: IPv4 Port Mapping

  Description: GenieGO

  Public UDP: If manual of the Consult of UDP user, enter the numbers of the port here (use commas to separate).

  Public TCP: If manual of the Consult of user TCP, enter the number in port here (use commas to separate).

  Private IP address: IP address of your GenieGO

  UDP private: same as the public

  Private TCP: Same as the public

  Select Save

  Update of TimeCapsule.

  Test.

• Port Forwarding/Asus router

  Can someone ' "guide me through Port forwarding

  I have the Cloud Connect Port information

  I have two TCP and UDP selected in Port forwarding protocol that I have selected "both" (TCP and UDP)

  I have a Service name field (LenovoCloud!... or is my "personal cloud name go here?) I also have a range of ports (4900:5300), then I have two other fields IP Local and Local port... What are my values for the last two, (my IP address, see the section called Personal Cloud parameters go here?) that I have however enter the numbers, my router Asus N66RU won't Port Forward...

  Thank you

  Frank

  For my Asus router, I have the following entries specifically for the cloud of Lenovo/Iomega ix2 - dl

  Iomega Personal cloud	443	192.168.1.101	443	TCP
  Iomega Personal Cloud	50500	192.168.1.101	50500	BOTH

  When the ip address is the ip address internal of the ix2 - dl. You will also need to open potentially other ports for other services, such as FTP, Torrent of Transmission, etc.

• Port forwarding for EYEMAX DVR on WIn Server 2012

  We use the router as a network controller on our local network. Now, we have replaced router with the server (win 2012 r2 essentials). We have an EYEMAX DVR client software to connect to a remote ip address in the web.

  Previously, I had the configuration of port forwarding router and EYEMAX was working. When we replaced the router with a server that I can no longer connect. I guess that there is a similar setting to perform on a server, but I can't figure out what to do. This certainly isn't a Firewall (when I turn it off EYEMAX still do not work).

  There is a statement (http://site.camtechsurveillance.com/downloads/remoteacc.pdf) how to configure a router to work, but I do not know how to apply similar changes on the server.

  TL; DR.

  How to do the same on the server like here http://site.camtechsurveillance.com/downloads/remoteacc.pdf

  Try asking in the Windows Server forum:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer