Portege M300: orange light flashes after spill coffee on the keyboard

Similar Questions

• [Solved] X121E not start after I spilled coffee on the keyboard :/

  Hello

  My X121e can not start after I spilled coffee on the keyboard, even when it is dry now (I opened and used a hairdryer).

  When I press the power button, the Red led turns on for a second and then it turns off.

  The fan remains off...

  How can I confirm hardware failure? Is there a reset button on this laptop? It is written in the user manual, but I couldn't find it...

  Thank you!

  Everything is OK now: it has restarted!

• Spill coffee on the keyboard and now 3 keys do not work

  I spilled coffee on the keyboard. Now 3 keys do not work. What should do?

  Replace the keyboard.  There is nothing here that can be repaired by a user, and wild stories you see on the Internet about doing things like «put the keyboard in your dishwasher and...» "will not work.

• spilled water on the keyboard, the keys do not work Ideapad Z500

  Hello

  A few hours ago I accidentally spilled water on the keyboard of my Lenovo Z500 Touch. The PC was only going to batteries, not connected with the adapter. I cleaned the water immediately. I turned it off, only it works a few times to see if everything was ok. Now (about 6 hours of the accident) most of the keys on the keyboard do not work. I turned the pc upside, hope it's just the water left in the keys, and now I'm waiting for the water to dry.

  any other advice?

  Thank you

  tonight I'm going to disassemble the keyboard and dry it with a hair dryer, gently and slowly warming not too. I have read that it does not disturb the guarantee as tha keyboard is a modifiable element.

  Any advice?

• Dell Dimension 9200. The orange light flashes. Power disconnect day + this market but stop and it will not work unless that unplugged for a day

  Flashes orange and no lights on the front panel next to the USB ports. (see amber light on motherboard, power button / stop 15 sec + he disappears, but the computer does not start, a few times the fan turned on couple seconds), initially it used to go in the cycle (starts for about 3-5 seconds and stops) several times and the flashing yellow light.

  If I unplug the power cord for a day + and try, it worked, stop and restart immediately worked too but when I shutdown and come after a few hours, it will not start again (power plugged).
  Disconnect the power supply for a day + new and it worked once tried.

  I did the reset by pressing the power button / 15 sec + but no luck. Until a day + unplugged worked so far about three times will try again tomorrow and see what happens if I don't stop the computer ever.

  What a PSU or of the motherboard problem or some other problem? Hope it can be fixed.

  Rav96

  Flashes orange and no lights on the front panel next to the USB ports. (see amber light on motherboard, power button / stop 15 sec + he disappears, but the computer does not start, a few times the fan turned on couple seconds), initially it used to go in the cycle (starts for about 3-5 seconds and stops) several times and the flashing yellow light.

  If I unplug the power cord for a day + and try, it worked, stop and restart immediately worked too but when I shutdown and come after a few hours, it will not start again (power plugged).
  Disconnect the power supply for a day + new and it worked once tried.

  I did the reset by pressing the power button / 15 sec + but no luck. Until a day + unplugged worked so far about three times will try again tomorrow and see what happens if I don't stop the computer ever.

  What a PSU or of the motherboard problem or some other problem? Hope it can be fixed.

  Rav96

  A flashing orange power LED, usually indicates a power supply problem power, given the age of the Dimension 9200, which is highly likely.

  Try to replace the power supply with a power supply of labour "Known", to see if that makes a difference.

  This system does not use an exclusive power of Dell, you can install most power supply ATX with a power connector 24 pin or 20 + 4 pin main motherboard and this can be purchased in most local computer stores, or online.

  The 9200 has a rear panel open, a diet with or without the on/off switch can be installed.

  Note: You need a PSU with six SATA power connectors.

  Otherwise, you can buy a refurbished Dell OEM [Dell P/N KH624] 375w PSU from here:

  http://www.Amazon.com/Dell-dimension-power-supply-KH624/DP/B0039OHV2O

  Bev.

• impossible to connect or reset orange light flashing

  I read 100 amber streetlights, but have not met my situation at the moment.

  Flashing orange light on my 1470 time capsule.

  It does not connect to utility

  It will not be reset in any shape

  It has been cleaned, its is not overheated, it has a lit solid when modem connection.

  I read the possible motives of questions but no connection I can't even help out at this stage.

  Very expensive paperweight?

  Thank you

  Matt

  Have you tried to use the reset on the back? I believe that the orange light is a configuration problem - I get on mine when the network has changed and there is a configuration problem.

  • Reset to a base station AirPort FAQ - Apple Support

  I used a soft reset, which resets the SSID or connects via a cable, and then allows me to run the utility to reset the configuration.

• Satellite M110 - Orange light flashes when I push the power button

  just before I managed based on the knock off my bed, on a glance the plug that goes into the computer look slightly bent and now when I try to turn it on, it does not work. even when it is plugged.

  An orange light is always flashing down the bottem when I press the button.

  So is this a problem computer or a power supply problem?

  Hi becks88,

  Sounds like a serious problem of material... You can start Notepad without AC/DC adapter or is the battery charging adapter?

  Try to delete also the adapter AC and the battery for an hour at least. Then reconnect the two and try to start the laptop.

  In the worst case you need professional help a :(authorized service provider

• I just bought an Airport Extreme and try to put in place.  I have Fios cable with a router.  I can not get anything except a blinking orange light.  After reading the instructions, it seems that the problem with the ethernet cable but I

  Must not exceed the flashing orange light.  have tried three ethernet cables to the Fios router.  All thoughts

  What extreme version do you have?

  Test the cables connecting the airport to your Mac with them and see if the ethernet works on Mac. Green connectivity light should go... If it fails, then the AE died.

  Please do a factory reset, then try again.

  Sometimes Mac airport utility works well... If you have the preference or iphone ipad, download and use iOS version airport utility and try it for configuration... It is much less awkward.

• DeskJet f4180: always E error message and empty cartridge light flashing after installing new cartridge

  I always get the error message E and empty flashing cartridge light after installing new black cartridge.

  Welcome to the @vinylzappaforum!

  I read on the 'E' and the empty cartridge light blinks after I installed a new black ink cartridge. If you have tried the guides that I suggested in our other thread here, so the next step would be to call phone support at HP to discuss your printer options coming with them. I let the info below.

  Please click the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Contact HP:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• HP Officejet Pro K8600: Power light + resume light flashing after printing only one Page

  After trying to print a document of several page, the printer produced a page and then the power light and the resume light (page feed) Flash. I also tried to print multiple copies of a page, but that leads to the same result.

  I can get the lights extinguish by turning printer off then turn it back on. But it will always print that one front page the same lights begin to Flash. I did six times in a row just to print a six page document.

  I went through all the steps in troubleshooting HP software. Not like searching for cleaning print heads, re-seats cartridges, etc., fragments of paper. Nothing seems to work.

  @Bob_Headrick

  Thank you for your response. However, none of the suggestions could solve the problem. ALTHOUGH the light guide troubleshooting that you provided was close to the solution.

  I came across the solution by reading the PDF manual for the printer. On page 77, it describes the power led + resume light flashing. One of the causes for this using EXPIRES of CARTRIDGES of INK, CARTRIDGES RECHARGEES or NON HP CARTRIDGES.

  WARNING: It is important to note that if your printer is still under warranty, DO NOT DO THIS. HP notes in the manual using this substitution can void the warranty against damage caused by the use of faulty ink cartridges, obsolete or not allowed.

  SOLUTION:

  While the power light and button resume flashing, press and hold the power button and press the button repeat 3 times. This replaces the "apparent" internal error message to use the cartridges you have installed. It may also cause a print cartridge alignment page.

  MY OPINION:

  It is important to note the HP cautioned against it, it FIXED MY PROBLEM IMMEDIATELY! I know that the cartridges that I have installed are in agreement. Like many HP owners out there, I take advantage of sales and have stored on cartridges. I guess some may "expires" before you install it. In my view, the idea of "expiring" cartridges also somewhat falls into this column to "How can do us buy more ink?" What kind of market we create where it's cheaper to buy a new printer than to buy a new set of cartridges/toners? BUT it's a slippery slope... let's not go there.

• Satellite A50-11: spilled water on the keyboard

  I spilled water on my keyboard while I was working with my laptop. I immediately turned on and tried to dry it. It has been 4 days but I can't still turns on. The LED flashes orange, and I read in the manual that it means that there is a change of the voltage of my laptop.

  I'm recently in Germany/Stuttgart and called the center of service/support of the Germany million times, but I waited on hold for hours: S I need my documents and I want to save my laptop. What should I do? Immediate responses are expected.

  Hi Elif,

  Sorry to hear about your mishap with your laptop. Fortunately, if it wasn't water that you spilled on your laptop then it will eventually dry out and the unit should suffer no lasting damage. I would recommend that you remove the battery and AC power and turn the computer laptop (with the lid open) in a warm and dry (for example a distribution Cabinet) to allow residual moisture to evaporate completely before attempting to turn it on again. Note that this may take several days depending on just how the water mucj was reversed and how she managed to seep into the device.

  It is also possible that the water shorted out some of the internal electronics of your laptop before you managed to turn off, if the drying technique above does not work then you may need to unit control/repair by an ASP. Fortunately, it is likely that you hard disk (and, therefore, your data) will be damaged by this incident.

  Kind regards

• Fixing orange light flashing on Airport

  I use an Airport Extreme Base Station for a MacBook Pro running OSX 10.11.5 and the yellow LED flashes. So far I'm not having any problem, but I don't want to suddenly have a problem when I REALLY need an internet connection. I found a thread of community Apple earlier that said to download the latest version of Airport utility software. However, when I down load 6.3.1 which was the latest version that I could find, I was told that it was not compatible with my OSX. All of the suggestions.

  The MacBook Pro running 10.11.5 already has the latest version of installed AirPort Utility, which is 6.3.6,, so don't worry about this.  You can check if you like... it just open AirPort Utility and click the AirPort Utility menu in the upper left corner of the screen next to the Apple icon. Then, click on about AirPort Utility to display the version number.

  The yellow light blinks because your AirPort Extreme has a message for you. To find out what it might be...

  Open AirPort Utility and click on the image of the AirPort Extreme

  In the window that appears, you see a button update?  If you do, then there is an update of the firmware for your AirPort Extreme. Click Update to install the firmware if you have the most current firmware for your airport.

  If you don't see a button not update, then search for a list of status and click on the little orange dot it for more information on what could be the issue and one suggestion to remedy what the airport is whining.

• Satellite L850 - 1-5 - no battery not detected and slow down the orange light flashing

  Hello

  I'm helping a friend with a problem with its Satellite L850 - 1 5.

  No battery detected is report to Windows, and the light on the front of the machine of battery flashes orange slowly.

  I saw a few forums suggesting removing the power and the battery and holding down the button for 30 seconds. I tried a few times and seems not to have had any effect.

  Is there something that can be done, or is broken for good battery?

  Thank you
  James

  Remove the battery and start your laptop with AC power only. What happens when you put the battery in place when Windows is fully charged?

• IPhone SE lights not after an appearance at the screen frozen, faded and an attempt to hard reset.

  I just took the new smartphone Iphone SE in April 2016. It worked perfectly fine for the months that I had it until last night. I was recording playing me the guitar, when I put the phone down with the camera open for a few seconds. When I went to get the phone upwards, the screen was frozen and colors have been melted. The multicolored lines appeared as well. I tried to close the application by pressing the home button, and when I tried to press the sleep button to access the lock screen, the phone went black. When I went to press the sleep button to access the lock screen, the phone opens the same screen frozen, multicolored as before. I panicked and hard reset the phone. I turn on is no longer the phone. No apple logo appears, as well as logos 'connect to Itunes '. I tried to restore the phone to factory via Itunes, but it was without result.

  Surprisingly, when I went to restore the phone, the second time, serial number has changed from a game of numbers and letters invalid "s/o," as if Itunes is no longer permitted to detect it as an iPhone. In addition, the phone is now considered as a completely new system on Itunes, which I don't know is normal.

  I made an appointment with the Applestore for tomorrow, but I would like to comment on what someone thinks that this problem could be. I have not tried to Jailbreak the phone somehow, but have the feeling that my phone may have been hacked, or perhaps he is being malicious programs? Maybe it's a motherboard problem or display?

  Any comments would be greatly appreciated.

  -B.S.

  I made an appointment with the Apple store for tomorrow, but I would like to comment on what someone thinks that this problem could be. I have not tried to Jailbreak the phone somehow, but have the feeling that my phone may have been hacked, or perhaps he is being malicious programs? Maybe it's a motherboard problem or display?

  Your phone is not hacked and all the malware only you could catch is malicious cookies in Safari or other browsers that are removed easily by clearing their cache. I suspect you have a hardware problem, nothing more, that should solve the Apple store.

• MacBook pro 2015 stuck in Bluetooth Setup mode after commissioning, recognizes on the keyboard and track pad. SMC reset does not work.

  My Macbook Pro 2015 stopped periodically (and now permanently discontinued) responding on keyboard and touch pad Board. This seemed to start at the same time, I got a Bluetooth headset; When I turn on the computer, he's stuck in Bluetooth Setup mode. I tried to reset the SMC, and it does not work. I don't have a Bluetooth keyboard to even try with it. Also, I can't start in safe mode. It seems completely blocked. Any help you might be able to offer would be great!

  Hello rad trp,.

  Thank you for using communities Support from Apple!

  From your post, I understand that your keyboard and trackpad on your MacBook Pro are unresponsive and now you see the Bluetooth set up screen on the computer. I also see that you tried to reset the SMC, but that doesn't seem to work because the built-in keyboard do not respond.

  I know that you do not have a bluetooth keyboard, you can connect, but you have a USB keyboard? Even a USB keyboard for a computer Windows will work. If you do, I would say connection that the keyboard and you use these keys to perform an SMC reset, but reset the PRAM as well. Instructions on both of these resets can be found in the links below if you need.

  Reset the management system (SCM) controller on your Mac - Apple Support

  OS X Yosemite: reset PRAM your computer

  See you soon!