print photos onofficejet 8600 pro

Similar Questions

• Printing with HP 8600 Pro

  I have a HP 8600 Pro. I use an HP Pavilion laptop with windows 8.1. I printed a document that had 2 pages. 1 printed page, then I shut down the computer. (my mistake)

  I turned the computer back on and tried to print in word, it says that 2 documents were pending. I tried to cancel the 2nd document and in the State, he said "delete", but it takes a long time. I turned off the printer hopeing that would clear it, but it didn't.

  Now, I noticed that when I prine I get 2 things that say the following...

  1 HP Officejet Pro 8600 (network)

  2 HP 4DEDB (HP Officejet Pro 8600)

  If I use the HP Officejet 8600 (network), the printer prints. If I use #2 it will not print because it shows the State of the removal. What can I do to fix this? This printer is also used by my iMac.

  Hello cbbob,

  I understand that you get problems printing documents using the Officejet 8600. I will do my best to help you! I recommend you remove the second printer, the first printer is to print a document. Please follow these steps:

  Follow this document here how access to the devices and scanners on Windows 8.1. Now right-click on 4DEDB HP (HP Officejet Pro 8600) with your mouse and choose Remove device. You can do a right click on the HP Officejet Pro 8600 (network) and select set as default printer.

  Please let me know if you have any other questions. Have a good night!

• Problems when scanning double-sided printer Officejet 8600 Pro Plus

  Hello everyone

  I recently bought a printer HP Officejet 8600 Pro Plus (CM750A n911g)

  I am facing difficulties when more than one original double face scanning by ADF.

  A single page works fine, but with several pages it works in about 10% of cases.

  This is what is happening.

  In normal situations, side of first page the page is parsed, page is hit, second side is scanned, new page flips and ejects the page.

  But there are times that when the first side is scanned the first page is fed into the ADF, the second page we begin to slide into the ADF, because the upper feed Dungeon rollers turning at this time here in time.

  For the moment that first page trying to flip the machine 'sees' the second page and decided to eject the first page without analyzing the second side. It begins directly to scan the first side of the second page. (image is reversed 180% because the machine "thinks" it is the second part of the first page)

  This is happening (not always, sometimes some pages are treated as it should be) up to the last page.

  Last page is always correct, since there is no next page more to disrupt the process.

  Anyone know what to do to avoid this behavior? The paper used is normal paper 80g.

  I installed the latest version of the firmware in this machine (CLP1CN1304AR)

  I'm starting to think that this could be a bug software and superior power rollers run too long.

  I've tried different settings and this happens when starting a scan of the computer, but also when starting a scan of the screen touchscreen printer.

  Thanks for any answers

  Kind regards

  Ronny

  This one is over.

  For those who might be interested, he has focused on the machine.

  Machine update itself to works and always the latest version of the firmware very well

  Good bye

• Copy/scanninf with HP Officejet 8600 pro problems

  I have a desktop HP all-in-one running Windows 7 (64-bit). The printer HP Officejet 8600 pro range is connected to the printer via a USB cable. Scanning/copying is all lines verticle edge edge of the paper. I ran the HP scan doctor software and it showed that everything works. Still no usable copy. Search HP site and the forum of solutions. Tried what I found. Still no solution found.

  Well, I thought was this Chantilly when a blogger told me to try another outlet. It worked for a while. Now, the scanner lamp isn't bright lighting as it did before. She is dark, almost orange. The printer's two month warranty. Is this a bad sanner lamp or something else?

  Can someone help me solve the problem?

  Thanks for the pointers. I'll try them and I hope that this solves the problem.

• Scan/copy with HP Officejet 8600 pro problems

  I have a desktop HP all-in-one running Windows 7 (64-bit). The printer HP Officejet 8600 pro range is connected to the printer via a USB cable. Scanning/copying is all lines verticle edge edge of the paper. I ran the HP scan doctor software and it showed that everything works. Still no usable copy. Search HP site and the forum of solutions. Tried what I found. Still haven't found a solution. I would set an example of a scan, but I see no abilty to attach a copy of this message. Can someone help me solve the problem?

  The scan looks like the following image?

  

  It s probably a power outage in the lamp.

  1. try to change a different electric recessed contact.

  • 

  2. check the scanner lamp, if he shines a light "BOLD" when the printer is turned on.

  • 

  3. try to start a new search and check the operation of the scanner and how works.

  • If the problem persists, this means that the scanner lamp has a hardware failure.
  • To contact directly to Hewlett Packard to ask the repair options available:
  • Contact HP > http://www8.hp.com/us/en/contact-hp/contact.html

  * Click the stars KUDOS to say thanks

  * also click on the Solution button if your question is answered.

• HP Officejet Pro 8600: Recently a fax pops up when I try to print photos and the picture does not print

  We have a printer all-in-one HP Officejet Pro 8600 operating from a desktop HP with Windows 7. Recently, in the last two weeks my wife told me, we cannot print photos. The documents appear to be printed without a problem, but when trying to print a photo we get a window titled 'Send Fax - HP Officejet Pro 8600'. We have never used or even hung fax capablitly since we have owned this printer (maybe 2-3 years). All of a sudden, this window is displayed when we try to print a photo and the photo does not print.  I can't tell you that my wife did not hit accidentally a wrong button somewhere down the line, but she says she does not. I tried to attach a screenshot of the window, but for some reason that it does not take it. It's probably something very simple, but technically challenged myself, I can't understand. Help, please.

  Thank you

  Vince Pellerito

  Print picture of what program?  Some programs to keep their own default values for the printer.  It seems that the default printer for the printing of the photo program has been set to Fax.  Try to open the program, select the Officejet Pro 8600 as the printer rather than the Officejet Pro 8600 fax.

• OfficeJet Pro 8600: Printing photos - too yellow

  Hello

  Whenever I try to print photos from my Mac to my officejet pro they have too warm/yellow.  I calibrated my monitor with a Spyder Elite 4.  Yes I know there is a difference between the light reflected and planned but this yellowing is great, people are not 'tired' looking - they grow soured range...

  Is there a way to specify the way a different ICC when printing on a Mac?  I'm trying to print from Lightroom CC edition is of no importance.

  Thank you.

  Hello

  Finally understood my problem.  My problem is that my monitor while it is calibrated, was not accurately reflecting the white balance of the picture.  Thus, while the photo looked GREAT on my screen, it was distorted "hot" which appeared in print.

  White balance setting solves the problem.

• HP Officejet Pro 8600: Thin vertical lines when printing photos

  The printer referenced did a fabulous job to print photographs.  In this case, the printer is fairly recent and has recently recently consumed the original cartridges when it was decided to try to use it for photo printing.  Therefore, the fabulous results were extracted relatively new cartridges and consisted of at least a dozen photo printing in various sizes.  Then all of a sudden these thin vertical straight lines began to appear in print.  They are equidistant on the full image.  That they appear in the printed image.  When using paper letter (8.5 x 11) to print an image cropped at 8 x 10 with landscape orientation spacing is about 1 1/8 (one and one-eighth) inches or 8 evenly spaced vertical lines.  Somewhat like the photo was divided into 8 columns.

  According to the printer built in ink gauge, that the cartridges are now just a little more than half full.

  These lines are narrow enough so that they are not very visible when printing on normal paper (copy).  They would probably be imperceptible on many kinds of printed documents.  However, they become quite noticeable and reprehensible when using good quality (in this case HP) photo paper to print photos.

  Absence of a printer resolution is not good for photo printing.

  In addition to the troubleshooting suggests that the problem is not due to the printer, but rather to the software used to perform the printing. It was not immediately obvious that I printed only photos using Picasa and it worked fine and then all of a sudden the problem developed. However, I have now tried to print the same photos with other software and there is no problem for the steps.

  The Picasa forum also has many messages wanting to be the same or a similar problem to what I have experienced. Unfortunately, there doesn't seem to be an explanation for a repeatable cause, nor a specific solution. Some hacking autour with the settings and options seems to be in order. If it does not then print with other software may be necessary.

• Now my HP Officejet Pro more will not print Photos or anything else!

  Here I am once more.  I finally solved the problem that I had been downloading the software for my HP printer after that I downloaded Windows 10.  I could not download any software without getting an error message 'download cancelled '.  I was able to print pictures and letters typed with WordPerfect X 6.  I'm embarrassed to say that I accidentally fell into the solution and now I can scan, send faxes again.  Yay!  Problem is NOW, I'm more able to print photos, or anything else!  I go through all the motions and send the message to the printer to print, but nothing happens.  I have already run the hppiw.exe and configure the printer.  When I try to run the HPPSdr.exe, he unzips the file, the printer appears as "installed" and click on the 'Next', I get a screen with 3 different ways to connect the printer to my computer - I choose USB because it'S the way I was connected.  Then I get a message telling me to do that my printer is on (it is)!  and try a different USB port (I have) or try another USB cable (I HAVE!)  OK, so FINALLY I get to the point where I am able to print on a HP Officejet Pro 8600 N911g series Print Page of Diagnostic quality, AND DOES IT!    But I also know there is a problem with the software and I need to uninstall and click the Support link and the Driver to download new software.  But when I click on the link, I'm told I'm not connected to the internet - here we are again.  I'm exhausted.  I am 65 years old and I've been at this for 96 hours.  I've corrected the problems of scanning, but now I can't print while yesterday I was able to do it!   Arrrrggggghhhhhh.

  Can someone tell me why I get the message 'not connected' when in fact I AM connected to the internet?  sigh/smh

  Hi @Galego,

  Welcome to the HP Forums!

  I see that you can not print with your HP Officejet Pro 8600, on 10 of Windows, and I'm happy to help you!

  Please, try the steps in the following order:

  • Uninstall the software. Uninstalling the printer software.
  • Unplug the printer USB cable.
  • Clean boot the computer. How to perform a boot in Windows.
  • Disable all Antivirus programs. Disable Antivirus software.
  • Disable all firewall programs. The WF of end-to-end.
  • Create a new user account. Management of user accounts and connections (Windows 10).
  • Reinstall using the printer HP install wizard for Windows. (Wait for the software to tell you to plug in the USB printer cable).

  Then, run the HP print and Scan Doctor to verify that everything works.

  I hope these steps help!

  If this, or one of the posts on this thread, helped you to solve the problem, please click 'Accept as Solution' said post. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

• HP officejet pro 8600 printer: print the job stuck in the queue for a printer hp officejet 8600

  I try to print a document on my 8600 pro hp officeject and printer, but it will not be printed because there is a print job stuck in the queue.  I tried to cancel the print job stuck but will not remove. I tried to turn off the printer, but it still won't delete. Can you tell me how to cancel a print job that is stuck in the queue?

  Hello

  From the desktop, hold down the Windows key and press R.  In the run window, type services.msc and press to enter.

  Scroll down to the print spooler service, right click and select Properties, then click the Stop button.

  Now search for C:\Windows\System32\Spool\PRINTERS, then delete the work inside this folder - you may need to click a command prompt to get the authority to open the PRINTERS folder.

  Restart the computer and you should find that the document has been deleted.

  Kind regards

  DP - K

• print from Fax on my 8600 pro history

  Do not receive faxes on my 8600 pro can not haue what it set up right.  Received a fax known and he receifed all 13 pages, but not print them.  Looked in the history of the fax received and found that he received, but the deal was the printing of this story.

  Anyone know what I did not any so he can print a fax received?

  If the fax was never printed, he might still be in memory. Select Configuration, then Tools, then "reprint faxes in memory.
  Touch? and "Product Tour" to learn more features on this great officejet.

• Printing from an iPad Air to a HP 8600 Pro problem

  I just bought an iPad Air and and I'm not able to print on my HP 8600 Pro. I have an iPhone 5 and able to print via the printer Pro for the iPhone. The free app Pro printer does not recognize the HP 8600. What should I do to be able to print from iPad Air to the Pro 8600?

  afprinter,

  Welcome to the HP Forum.

  You can use the free print Mobile HP eprint for iPad application:

  Instructions

  How to print with an iPad, iPhone or iPod touch

  • Open the link
  • Open the document linked, then the Section ePrint or Non-compliant ePrint printer
  • Then, open the mobile application of section HP ePrint

  Reference:

  HP ePrint Mobile App FAQ

  Cool application:

  HP all-in-One Printer Remote

  Click on the thumbs-up Bravo !

  It's a nice way of saying 'Thank you' for help.

  While I strive to reflect best practices of HP, I do not work for HP.

• Printing photos with HP Officejet Pro 8500

  Photos printed in HP Officejet Pro 8500 on glossy paper, does not provide ink and photos of defamation

  Here is what I think happens, 940 inks are pigment based inks. I know not developed photos media says it supports both, but I think you'll have better luck with a medium that is designed just for inks pigmented at base. One of my colleagues suggested looking for photographic support with color lock joint.

• HP Officejet Pro 8600 Premium: I have a printer HP 8600 pro works fine with my Windows 7 computer, but not with Windows 8.1

  I have a printer HP 8600 pro works great with my computer Windows 7 & computer laptop, but not with my laptop Windows 8.1. When I tried to print wireless (I didn't try connected), it would print only the first pages of 2 or 3 of everything I tried to print. I uninstalled the printer and inserted the CD to try to re - install and I got an error message indicating that the printer does not work with my operating system. I was able to install it earlier, but now, it will not install at all.

  Too bad. I'm sorry. I'm went to the HP Support Web site & downloaded a new driver & now it works!

• OfficeJet Pro 8610: Printing Photos

  Hello

  I have an Officejet Pro 8610 and whenever I try to print photos on photo paper, that the pictures come out running together and wet with I can do to fix this

  Hello

  The 1st thing I would check is the orientation of the paper in the printer.

  Make sure the print side on the down in the status bar (pg 25/36 in the user's guide)

  Also can I suggest to check the printing on the printer settings.

  Below, I have attached a link to the guide of the user of this printer, it should help.

  Guide to pg45 of the user (with print)

  http://h10032.www1.HP.com/CTG/manual/c04204791

  Please let me know if this was helpful.