problem after sp2

Similar Questions

• Tecra S1 problems after SP2 installation

  I have a problem when I use SP2 on my Tecra S1. After you install SP2, my pc crashes when I use the function 'stand by' or 'Hibernate '. It comes with a conflict of interrupt on irq 11 and begins to restart again. Whenever the pc starts again, the blue screen appears with the problem to irq 11 and the program that does, it apears at the bottom of the blue screen, should be "gv3.sys. I did al updates on ' information to update the driver for Windows XP with Service Pack 2 - v1.1.pdf ", but without success. The pdf file say I need to update the driver power saver to version 1.00.34M version, but I can't find it on the site. I use the Dutch version of WXP and the only driver I can find on the Web site is the 1.00.32M version and the English version is the 1.00.34M, so maybe that's the problem. I tried with a clean version directly from the restore CD but I came up with the same results.

  Who can help me to fix this, or point me in the right direction.

  Hello
  you are absolutely right! The 1.00.32M version is the most recent for your machine (for the Netherlands).

  Do not irritate cause there is a version higher than for other countries. The functions are equal.

  Try again with this version and keep us updated, please!

  Good bye

• Boot problems after installing Vista SP2 (KB948465)

  I installed SP2 via update.  During the update process there was a power failure.  After that (I don't remember if it's immediately after, or if a few days elapsed) I had problems with the startup.  Initially, seemed the Startup Repair to fix the problem, but not permanently, and the Startup Repair had to be used repeatedly just to start.

  After a few times of what is happening, Startup Repair did not turn, and the PC wouldn't start.  After about 5 attempts using the decision-making power, sometimes choose the Startup Repair, sometimes choose to load windows normally, he did start.
  I immediately did a system restore to return my PC before SP2 was installed.

  After the restoration of versions prior to SP2, Windows Update showed that the SP2 update failed.  It was on 9 November.  As I need my computer, I didn't reinstall SP2 until I had finished this work.

  As I thought that the problem is probably caused by the power outage, on 10 September, I reinstalled SP2.  Windows Update show no SP2 as an available update, then I downloaded and installed the standalone update.

  Between the 10th and today, 14, Windows Update has installed more than updated.

  Today, I was unable to start for the first time since the reinstall SP2 and Startup Repair has allowed me to open a session.
  I tried to uninstall SP2 via update.  The first part of it seemed to work, but when it came to reboot, the PC stopped at the end power to the bottom of the procedure.  I used the power switch to turn the PC back on.  After startup, the PC told me that deletion failed.

  Then I tried the system restore.  Unfortunately, the first available restore point was post - SP2 installation.  I restored it for the point that is as close as I could.  I tried to uninstall SP2 again through Windows Update.  This time, I receive a generic error message immediately (less than a second) - it does not attempt to go through the configuration - restart the procedure.

  I haven't restarted my PC since then.  Most updates have been downloaded automatically, and the PC tells me that a restart is required.  I'm a little worried that I will end up with a completely insensitive PC.

  I use an Acer Aspire X 3200 with Vista home premium pre-installed.  I don't have a Vista disc.

  Hello, Alex

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for Windows Vista Service Pack 2 (SP2) is valid until November 26, 2009. Availability of support chat or messaging differs depending on your location. Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack).

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Problems after installing KB978338 on Windows Vista SP2

  I met a problem after installing KB978338. The update installs without error or problem, but the system is extremely inadmissible after the reboot. The "\Windows\system32\config\systemprofile\desktop is not accessible" error, and the system is practically unusable. Normally opens the Task Manager and system seems inactive, but you try to start a new application from the Task Manager gave an error "hose is not valid.

  System is Vista Home Premium SP2 installed without any obvious problems before the update. Start the system restore and go back to immediately before the update of the results in the system back to normal functionality and responsiveness.

  I've never seen or either of these mistakes before and my research has not yet been able to find something similar, so I am at a loss to start this kind of problem with an update of troubleshooting.

  Please tell us how can I still troubleshoot or solve this problem.

  Thanks in advance.

  JohnBrown

  Halifax, NS

  So I "hid" the update and you call this one closed without resolution.

  While the overall rating of gravity for KB978338 is moderate (critical vs), it of still a security update and must be installed.

  Repost:

  See the section "How to get help" of http://support.microsoft.com/kb/978338

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  Purchasing problems of installation of the security updates Microsoft may also visit the following page for assistance:
  https://consumersecuritysupport.Microsoft.com/

  For more information about how to contact your local Microsoft subsidiary for security update support issues, visit the International Support Web site:http://support.microsoft.com/common/international.aspx

  For enterprise customers, support for security updates is available through your usual support contacts.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• DVD problem after installing Win XP Service Pack 2

  After installing XP Service pack2 son of college clicked on a question about activation of WinDVD 5 for Toshiba and now my DVD does not load the program. How can I fix it, remimbering I need help step by step?

  WinDVD is the least of your problems: WinXP SP2 should be installed no later than October 10 2006!

  If the computer running Windows XP Gold or SP1 until earlier, may not be a critical functional application of antiviruse protection installed and 3 + years of security updates have not been installed.

  See...

  Help: I got hacked. Now what should I do?
       http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows.  Please note that a repair installation (upgrade AKA on-site) won't fix this!

  HOW to do a clean install of Windows XP: see method 1 and http://michaelstevenstech.com/cleanxpinstall.html#steps in http://support.microsoft.com/kb/978307

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or one local network (i.e. other computers) otherwise and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Other useful references include:

  HOW to get a computer that is running Windows XP Gold (no Service Pack) fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.windowsupdate/MSG/3f5afa8ed33e121c

  HOW TO get a computer that is running Windows XP SP1 (a) or SP2 fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2b

  Tip: After getting the computer fully patched, download/install KB971029 manually: http://support.microsoft.com/kb/971029

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs or IE upgrades and before installing your new anti-virus application (which will require WinXP SP3 [1] needs to be installed).

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  Good luck!

  ================
  [1] extended for WinXP SP2 support ends July 10, 2010. After this date, the computers running under that WinXP SP2 will NOT be offered for additional updates of critical security, automatic updates do not work, and site Web Windows Update won't be available until SP3 is installed.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Computer won't start windows after SP2 updated which runs without error messages.

  Hello
  I have problem with SP2 update. After correct installation the computer not boot to windows and the screen is black.
  I have toshiba A55 S326 all of origin, on which I replaced HD (now 250 GB) and RAM (1 GB now). In past I have updated the bios to version 1.40 delivered by the producer.
  As I have new HD, I used the factory restore CD for Windows XP Home Edition. I have run all the updates that the system has been to download. Each think worked until I don't have install SP2. After correct instalation without error notice system invited to restart, I have confirmed, but the computer has not started load windows again.
  I tried several times, checked for possible errors, I used Critical Update 885626 before SP2 installin sugested, but all the time, same result. Black screen without loading Windows.
  You pls can someone advise for me what I have to do.
  As I have only the factory recovery disc, I'm not able to run the recovery console, because recovery is formatting disc before editing Windows.
  Can you pls suggest me how to get the WIndows XP or Windows XP Home Edition CD bootable recovery console.
  Thank you.

  Hi sake,.

  Welcome to the Microsoft Answers site.

  (a) you're able to boot in safe mode?

  If you are able to start in safe mode, then I suggest you to start in safe mode and install the recovery console that you already have a disk. See the article mentioned below.

  How to install and use the Recovery Console in Windows XP

  http://support.Microsoft.com/kb/307654

  I suggest you to activate the VGA (Video Graphics Array) mode and check. Follow the steps mentioned below.

  1 restart the computer and press F8 and choose Enable the VGA Mode in the menu options Start early

  Method 1:

  To use the safe mode option, follow these steps:

  1. reboot your computer and start typing the key F8 on your keyboard. Select safe mode from the menu.

  For more information, see the article mentioned below.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Let us know if it works so that we can solve problems more.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Huge problems after updateing to 31.1.2

  Hello

  I encountered several problems after the update to 31.1.2.

  1. I can't send emails from one of my accounts, or it only downloads the messages from this account. When I connect to this account's web e-mail messages are there. When I try to send the mail, I get the message:

  The message send failed.
  The message could not be sent using SMTP server mail.vista - consulting.hr for some unknown reason. Please check that your SMTP server settings are correct and try again or contact your network administrator.

  I have control over the mail server and reflected on the Messaging log and it said:

  2 Oct 17:08:37 droplet postfix/smtpd [10916]: connect from unknown [xxx.xxx.xxx.xxx]
  2 Oct 17:08:37 droplet postfix/smtpd [10916]: lost connection after unknown STARTTLS [xxx.xxx.xxx.xxx]
  2 Oct 17:08:37 droplet postfix/smtpd [10916]: disconnect from unknown [xxx.xxx.xxx.xxx]

  When I try to send mail.

  2. the update of enigmail and ligntening had stuck somhow. In the Add-ons Manager window, I see the old versions and new (lightning 2.6.3 and 3.3.1 enigmail 1.6 and 1.7.2). However, the new versions has dimmed. Restaring Thunderbrid does not help.

  3. all my entries in the missing calendar which is a very big problem for me.

  Best regards

  Andrija

  Close Thunderbird and go to your profile folder.
  There is a subfolder "extensions".
  Find the folder for both the lightning and Enigmail under "extensions" and delete them.

• Satellite Pro L850 - 1-8 - a few problems after the last update to BIOS version

  Hello.

  I have some problems after that the latest bios upgrade to version 6.80. First of all, I would like to note that Setup of HW does not work for me. I tried to use this tool to change the settings of the bios without success. This was done also by running this application with administrative privileges without success.

  The initial problem appeared after I tried to disable "open Panel - Power on" setting.
  This has been activated before the update bios and at some point I wanted to disable, because he gave me a nightmare when you carry because she would then put the computer in a bag.

  No matter how many times I tried to turn it off, it seems always enabled in HWsetup.
  Another feature that I can't edit's startup speed.
  It remains fast even if I tried to change to normal.

  I'm on Windows x 64 8.
  The case is now.

  GROUP OF EXPERTS
  HWsetup reports Open PANEL - PANEL as activated, while the Bios shows it off. It is indeed turned on and I could not turn it off. I even tried him for in the Bios and then try to disable in HWsetup, no change.
  STARTUP SPEED
  HWsetup startup speed related to 'NORMAL' but actually is 'FAST '. In the Bios, it reports its normal, but its easy to say to his FASTING in.

  My questions are.
  1. it can be the cause?
  2. How can I reset all of the values in the Bios to see if that fixes anything to start?
  3. is it possible to Flash the Bios with a version more old to see if this corrects the problems I have?

  I should also mention that 'System settings' has never worked for me. I get a message "Supervisor password check failed". Please note, there is no installed password.

  I will be grateful for any given solution. Thanks in advance.

  Can you please tell us which model of laptop you have exactly (the complete model name)?

• problems after the automatic updates

  I have Pavilion g7-2235dx with Windows 8.1 operating system. Almost all automatic up-to-date mess to the top of my ability to get on the internet. The only way I can connect is to uninstall all updates. The icons on my desktop has also stopped working. When I click it, it will immediately on the desktop. Cannot pin them to the taskbar either. Those on the taskbar does not open by clicking on them either. Have to click straight and say to open. Also problem get my Norton antivirus to open. Says it works but can not open it.

  Hello
  
  It might be, the upgrade to Windows 8.1. I've seen people with complications get the upgrade to go "smoothly".
  
  You can try, do a system update that would take you back to Windows 8. See if you have the same problems after updates.
  
  If you choose to update again, make sure that everything is already successfully updated.

• TFncKy.exe problem after upgrade to XP SP3 on Satellite A200

  Hello

  After upgrade of XP SP3, I have problem with TFncky.

  _System_:
  A200/PSAE7
  -XP Pro (2 x with OS selector, 1 OS XP XP main, 2nd XP for games)

  _Problem_:
  After booting XP from my main XP installation I always get an error message pop up stating that there is no prob with TFncKy and TFncKy should be stopped. As "signature of the problem" I get the following:

  + AppName: tfncky.exe AppVer: 3.22.0.0 ModName: ntdll.dll +.
  + ModVer: 5.1.2600.5512 Offset: 00012ace +.

  With one of the following keys on keyboard always results in above described error pop up but key are functional:
  WinLogo, DEL, HOME, PGUP /-DN, END, right SHIFT, FN + keys F etc.

  My second installation of XP (Lite for games) short smooth after SP3 upgrade: no error TFncKy error message.

  As my second XP runs without any problems after SP3 I'm not sure if the proplem is related with + tfncky.exe + or + ntdll.dll +.

  BTW:
  What driver package includes "tfncky.exe? Toshiba controls?

  Thanks in advance for any information or advice for this problem!

  Best regards
  Andreas

  Hello

  the problem was already discussed in another thread: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=18082

  The last message was probably the solution for the whole of the case. The mentioned user that "TfncKy.exe" belongs to the Toshiba Hotkey utility that only needs to be removed and reinstalled for this problem.

  In addition, it would be wise to check the registry with CCleaner for example before you reinstall the Hotkey utility.

  See you soon

• I'm having problems after the restart with docking station, applications, etc.

  OS X: 10.11.3

  Mac Pro 2010 2 x 2, 66 GHz 6-Core

  Graphics NVIDIA Quadro 4000 card

  24 GB Ram

  50 GB of free memory

  4 additional hard disks

  Hello community,

  I have a strange problem, after the mac is restarted, even when I decide not to join his joined apps a former State of the saved request. I can't make changes to the dock, after restart it restores an old state. When I try to import or save something in any application you see normally last modified files, yet his watch an old state. When I try to delete files that I always put my password, it's new. Im confused, I'm a long-time os x user since 1999 has never had this kind of problems.

  Help, please.

  Lars

  Please, back up all data before proceeding.

  This procedure will unlock all your user (not system files) files and reset their ownership, permissions and default access controls. If you have voluntarily set special values for these attributes on any of your files, they will be be restored. In this case, either stop there, or be ready to recreate the settings if necessary. Do that after checking these settings that did not cause the problem. If none of that is meaningful to you, you need not worry about this, but do not follow the instructions below.

  Step 1

  If you have more than one user, and the one in question is not an administrator, then go to step 2.

  Triple-click anywhere in the next line to this page to select this option:

  sudo find ~ $TMPDIR.. -exec chflags -h nosappnd,noschg,nosunlnk,nouappnd,nouchg {} + -exec chown -h $UID {} + -exec chmod +rw {} + -exec chmod -h -N {} + -type d -exec chmod -h +x {} + 2>&-

  Copy the selected text in the Clipboard by pressing Control-C key combination.

  Launch the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Paste in the Terminal window by pressing Command + V. I tried these instructions only with the Safari browser. If you use another browser, you may need to press the return key after pasting.

  You will be asked your password of connection that are not displayed when you type. Type carefully, and then press return. You can get a warning to be careful. If you do not have a password, you will need to configure one before you can run the command. If you see a message that your user name "is not in the sudoers file", then you have not logged as an administrator.

  The command may take several minutes to run, depending on the number of files you have. Wait for a new line ending with a dollar sign ($) to appear, and then quit Terminal.

  Step 2 (optional)

  Take this step only if you have trouble with the phase 1, if you prefer not to consider, or if this does not resolve the problem.

  Start in recovery mode. You may be prompted to select a language, then the OS X Utilities appears.

  If you use FileVault 2, select disk utility, then select the icon for the volume FileVault startup ("Macintosh HD", unless you have given it a different name.) It will be nested under another icon of the disc. Click the Open button in the toolbar and enter your login password when you are prompted. Then quit disk utility must be returned to the main screen.

  Select

  Utilities ▹ Terminal

  in the menu bar. It will open a Terminal window. In this window, type this:

  resetp

  Press the tab key. The partial order you entered will automatically end this:

  resetpassword

  Press return. Opens a window to reset the password. You do not need to reset a password.

  Select your boot volume ("Macintosh HD", unless you have given it a different name) if not already selected.

  Select your username in the menu option allows you to select the account if not already selected.

  Under Reset Home Directory Permissions and ACLs, click the reset button.

  Select

  ▹ Restart 

  in the menu bar.

• Re: Satellite L300 - problems after installing Windows 7

  Hello

  I have a Toshiba Satellite L300 bought with Windows Vista 32 bit about 4 months later, I got my Windows 7 64 bit done.

  1 my laptop has startup problems after I installed the drivers give him additional drivers to go, but I have downloaded drivers for Windows 7 64 bit

  2nd I hear music and want to hear the next song is what I use, but not net if the keyboard fn +? don't not go and play / pause next thank you Stop and media player tased funtionieren not only the weis tase of modest silence

  P.s. to translate with google

  Thanks in advance
  Patrick

  Hi Patrick,

  To be honest, your ad is very difficult to understand and I don t know what you mean exactly.

  According to your assignment, it seems that you need a driver and you can get all the drivers here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  In regards to the FN keys you have Toshiba Value added Package, and Flash Cards Support utility. Everything can be downloaded from the official page of Toshiba.

• Satellite U400 - PSU40E Synaptics touchpad problem after the recent update to BIOS

  Toshiba welcome,

  I've tested this in reverse, this is why the statement in the subject as it looks. After upgrading the bios of 3.00 to 3.50 touchpad loses its precision. Very rude and useless its like that.

  I tried different drivers, everything, but the only way to really solve this problem was it downgrade to 3.00 OR uninstall the driver Synaptics completely. Second solution, unfortunately, is unacceptable, because then I lose some features, like click on contact, which I don't use and control.

  Best regards

  Wojtek

  Hey Buddy

  I U400 and the BIOS has been updated to the newest one.
  The touchpad works like a dream. I m using Win XP and Vista and there is NO problems after BIOS update!

  In your case, this may be only a software problem and I think you can use the Toshiba Recovery disk and could reinstall the whole OS from the Toshiba drive

  It is a really radical solution because the whole HARD disk may be formatted, but if the resettlement of these two drivers touchpad didn t help then I think this would be the last solution.

• Internet problem after upgrade to 10.11.3

  someone at face safari connection problem after the upgrade

  I'm having exactly the same problem.

  Is it possible to uninstall the 10.11.3 update and revert to the previous version?

• My touch screen has a problem after downloading the IOS 9.0.2. Already try apple advises the steps. But the problem still occur. Already done restart of strength. Factory setting Reset also possible. But still the same problem. Can only be used at one min

  Hello!!!

  IM Apple Fan.

  Purchased IM Ipad2, Ipad4, Iphone6

  Last month I already buy s Iphone6 +.

  Today I feel unhappy

  MY IPHONE 6 'history '.

  My touch screen has a problem after downloading the IOS 9.0.2.

  Already called and try apple advises the steps. But the problem still occur.

  Already done restart of strength. Factory setting Reset also possible. But still the same problem.

  Only can be used for a minute. After that... The problem comes in again & again & again...

  APPLE.COM

  Can U help me

  Only products of Apple of love before updating the version 9.0.2

  iOS 9.0.2 happened some time. The last iOS is iOS 9.2. If you have not updated, updated. If you restored to the factory, it must have downloaded iOS 9.2. Also, if you restore to the factory and the problem is still there, then you must make an appointment at the Genius Bar to the nearest Apple store or Apple authorized service provider or call the Apple Support to have the device examined by Apple. There seems to be something wrong with the screen.