Problem trying to understand HP Laserjet CP1518n on wireless network

Similar Questions

• Problems with the IP settings on XP pc wireless network

  I have (part time) a wireless network to recently set up. Router is connected to a pc windows 7, and there is a XP machine with a USB adapter as well. The PCs are turned on, and the XP shows a wireless connection with a 'very good' signal. When I try to start IE on XP it will fail to connect. When I then run the diagnostic network connection died at around the point where the diagnosis is trying to reactivate the adapter. The diagnosis of output reports "error renew IP address: semaphore timeout has expired" and "default gateway 0.0.0.0." If I then run ipconfig/all there is absolutely NO output. This happened yesterday, so I manually reset following IP 299357 instructions and the same thing happened again. I did the reset again and rebooted the XP. The router indicates that it has recognized the XP and ipconfig/all on XP shows things different, including

  IP 192.168.2.6. subnet mask 255.255.255.0; gateway by default, dns server, and dhcp like 192.168.2.3 Server (the IP address of the router); DHCP and automatic configuration enabled. IP routing and WINS proxy are disabled.

  While I was typing the above router lost sight the XP box, although the box XP still reports a 'very good' signal and a connection permanent.

  So far, I had this network in place for 10 days, but could not use the connection to the outside of the PC XP on a day, which followed my re - configure the router to its IP address 192.168.2.3 rather than recommended in setting up such 192.168.2.1, because 192.168.2.3 was that the XP box trying to connect as. Two PCs have been turned off during the night and worked fine when started the next morning for the entire day. The next day that XP had a connection for long enough to reach the site where I was looking for updated printer drivers, and then he lost when I started to download the and nothing since. IP information now suggests that I might have little joy for a while, if I still have to reset the IP address of the router to 192.168.2.6 this time, but I don't see why I should continue to do.

  Some of the other TCP performer? Troubleshooting IP connectivity:

  Ping 127.0.0.1 return OK; ping 192.168.2.3 expires; ping 192.168.2.6 is OK; ping host name does not work (assuming that the host name is just the name of the computer to the pc win 7); Pathping 192.168.2.6 works. (If that this watch is actually the host name and then ping that name does not work either, there is no entry in the ARP cache, do not know the valid IP addresses to test those.)

  Suggests that I have problems with the default gateway, and name resolution, but I do not know how to set resolution, unless you change the IP address of the router, which can do the first, but not the second.

  Suggestions welcome.

  The fact that things worked fine for a day seems to indicate that the material is OK, and I checked that I have the latest firmware for the router and USB adapter. Security of the router is disabled, as is the firewall on the XP, neither of which is ideal

  Technical support of Belikin has decided that the adapter was flakey too and should be replaced. If we call things the customer support, and I heard of them since, did not except a s message that seemed to ask whether or not I had entered with them...

  So what network?

  Packed wireless router and got some kit devolo for a network of current carrier online (on the grid) put in place instead. More expensive, Yes, but IT WORKS! 6 weeks later, still no problem to access Internet from a PC.

• Problems with 9191 chassis for connection to a wireless network

  Hello

  I can't seem to connect a 9191 unit to our network wireless with WPA authentication mode. I am trying to connect to based on SonicWALL TZ 105 Wireless access point router. Our wireless network is configured with the WPA2-PSK security. When I go to the page of network configuration of 9191 our network appears, but then I get the error 'Invalid WEP Key' when I enter the security key and try to save the configuration (see picture). I tried to use the configuration according to MAX and the web. I have also established that the wireless connection can be done if I change the security mode of the router to WEP, but neighther WPA - PSK or WPA2-PSK work. I have not tried security modes of type business because they are not setup on our network. I tried to play with the WPA security settings, but did not have much chance.

  Any advice will be much appreciated!

  Kind regards

  Misha

  Hi Misha.

  Apologies for not being clear - I was referring to the memory on the option of manual entry.

  Under network, select "other network".  This will allow to you manually type of entry security, SSID (network name) and WPA - PSK passphrase.

• at & t u-verse, & having problems connecting my Officejet 4500 to my current wireless network

  Hello

  I just got an Officejet 4500, and I am unable to connect it to my current wireless network.  I'm AT & T U-Verse so I use 2Wire equipment.  I have a Mac Book Pro, and I'm on Mac OS X operating system 10.5.8.  When I try to connect, I get an error message saying something like "Failed to connect."

  In the past, I had problems connecting my Airport Express to 2Wire.  In order to make it work, I connected the router 2Wire and changed the WPA - PSK (TKIP) security settings and WPA2 - PSK (AES) to just WPA2 - PSK (AES).  My Airport Express was able to connect without any problems.

  Please help me to connect my Officejet 4500 to my 2Wire router.  I note also that I'm not really tech savvy so I need instructions are written in simple terms.

  Thank you in advance for your help!

  Marc-Antoine

  Tanisha Hey! Try as part of this support document: AT & T 2Wire routers: "Login failed" or "Can't find printer" Message, or cannot connect to a wireless network

  I hope this will get back you on track!

  -Sean

• Problem with the cable on PC with usb54g wireless network

  I have a pc with a usb54g interface that communicates very well with my wrt54g2 router.  The router is 192.168.1.1 (default), and the pc has a static (wireless) address of 192.168.1.10.  My problem just is whenever I try to connect to one of the connections on the pc to a switch 100base2.  (The 100baseT interface is on 192.168.2.1).

  Whenever I turn on the switch, I lose my connection to the IP address that my satellite modem has attributed to the 'internet' on the wrt54g2 interface.  I am running Windows XP, SP3 on the pc.  Can I fix my problems with the installation of the network in the windows GUI, or should I change my command prompt routing tables?  I suspect that, when I get an address for one network other than that the pc is aware, he is trying to use the interface that he thinks is faster, obviously wired LAN.   I apologize in advance if this has already been covered on the forum.

  You can do this by using the GUI under Windows by changing the metric parameter of the interface under the advanced part of the configuration of the connection network GUI.

  See this LINK for more information:

  http://www.windowsreference.com/Windows-2000/change-the-interface-metric-on-a-network-adapter/

• Problems when using an extension to an existing wireless network wireless

  I recently acquired a Netgear WN2000RPT which is an extension of a network from a router wireless wireless (also serve as DHCP server and Internet gateway). The extender implements a network connection to the router and admits PC connected to the network extenders in a manner transparent acess Internet (through the router). All works well with Vista but not XP wih. My computer XP SP3 laptop works perfectly when connected directly to the router (and I used it in WiFi systems). When connected wired to the Extender, all right. BUT when connected wireless to the dilution, it does not work. Connection established (documented in the PC, as well as in the extension). But during an attempt to access the Internet the Extender loses (documented) IP address of the PC (on the PC is shown no sign of lost contact). NETGEAR is a wellkown provider, but their support is grateful no problems with XP. They claim that the error is in my PC but all the parameters have been proven in the chats and emails, to be correct. Although no no not a network specialist I know that Vista has been a big step forward in stability network adding even layers in the protocols. This could be a possible cause of the problem and, if so, is there an upgrade to XP (or a KB article) that could eliminate this difference?

  Good news and thanks for the comments.

  As far as IPv6 is concerned, a quick way to say should run ipconfig in command prompt window.  If IPv6 is installed, you will see it immediately.
  http://i.technet.Microsoft.com/dynimg/IC195932.gif
  http://www.windowsitpro.com/content/content/97365/figure_03.jpg

  If you want to uninstall IPv6, http://support.microsoft.com/kb/2478747

• HP Laserjet Pro M176n MFP: HP Laserjet Pro M176n on wireless network MFP?

  The difficulty in trying to get this printer on a wireless network. There seems to be available to set up the printer using the options available in the screen of the printer on a very limited help.

  Once that you have connected the cable to your router, insert and launch the Elf Setup.exe printer installation CD or download the latest version of the software from the HP site.

  If the software was already installed select adds another device and follow the steps, and then select a network connection once asked you how you connect to the printer.

  If you do not install its software yet the followed by the installation wizard until you saked how to connect the printer and select "through the network.

  If necessary, you can download the software of the printer below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=kJ-124897-3&cc=us&DLC=en&LC=en&OS=4063&productOid=5303439&sw_lang=

  Kind regards

  Shlomi

• pro place 8 wireless network connection problems

  I have problems connecting my venue 8 pro to a wireless network. anyone encountered similar to debug and fix issues/options?

  When sometimes, I had this problem, a deep discharge set: with power supply not connected, press the button of the Tablet for 30 or 60 seconds, including after the Tablet died;  Let the Tablet turned off for 2 minutes; and restart.  Have been informed by Support technique Dell that the cause is a buildup of static electricity, which avoids deep discharge.

• As a beginner, it's very basic, I imported my address book apparently ok, but I'm having a problem trying to address an e-mail to the address book in

  As a newbie it is very basic, I imported my address book apparently ok, but I'm having a problem trying to address an e-mail to the address book in the address field, I'm a right click, left click, but no list of addresses appearing or contact component which I should be able to see all the entries in my address book. What am I doing wrong please?

  Open a window of writing and press F9 to activate the touch pane.

• Is there a manual of Thunderbird? I'm trying to understand all the options to display/Threads.

  I'm learning to Thunderbird, hoping to adopt as my e-mail client (cannot float Eudora more). The forums are not effective for learning. Right now I'm trying to understand all the options to display/Threads, but tomorrow it will be something else.

  Hi Tom,

  There are some resources that I found for you to learn Thunderbird as you go.

  • http://en.flossmanuals.NET/Thunderbird/
  • https://cs.uwaterloo.ca/CSCF/HOWTO/Thunderbird/

• Satellite L300: problems trying to get the CD player work

  Currently, I have a Satellite L300 unit and have problems trying to get my CD drive work.

  Recently, I deleted the cd player, completely by chance instead of a printer.
  Now it won't reinstall and no update driver makes no difference.
  Anyone have any ideas?

  First of all, try to restore Windows back to a Restore Point prior to a date before the problem occurred. System Restore is in the start menu-> programs-> Accessories-> system tools

  Then try to remove the CD/DVD filters in the registry, and then restart. Windows should find the CD Player automatically, unless the registry has been messed up.

  When the associated CD/DVD (such as iTunes, Nero, virtual CD software), the software is installed, they install filters in the registry, which can cause compatibility problems.

  (1) run Regedit (start-> Run-> Regedit)
  2) navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  (3) in the right pane, delete the "UpperFilters" key and delete the key "LowerFilters".
  (4) restart.

  If your CD/DVD programs stop working, you will need to reinstall them (preferably with an updated version).

• Problems trying to use Ghost solution Suite 2.0 on Tecra M9

  We have recently bought a few M9s Tecras and now have a problem trying to use Ghost solution suite 2.0.

  It is necessary to install custom software every two weeks and have always used ghost solution suite 2.0 to recreate the image at a time, all our machines now the ghost starts and crashes before the session starts and then the fan goes mental...

  There are other posts that mention the use of switches in the cmd prompt, it works but only 1 machine at a time, which is of no use to us.

  How to use Ghost and image multiple machines at the same time?

  Arthur

  Hello

  It seems that you have some problems with this software, it freezes and I doubt it could be a problem with the laptop
  Why you n t come into contact with the solution of Ghost support Suite 2.0 in order to discover the question?
  In my opinion, this should be the first step to get some details why this software freezes...

  PS: since the Tecra M9 supports a SATA HDD controller you will need to include the SATA drivers to install and Windows operating system on this device, I guess that the package of the image that you created for several M9 contains the SATA driver files needed too. Check it!

• J4580 print cartridge problem: [Tri-Color] refer to the device Documentation

  Well, I'm starting to feel like I knew better, buy another HP printer after dismal luck with two all-in-one before.

  My J4580 already gives me headaches after only 6 or more months of use.

  The unit refuses to print, declaring "print cartridge problem: [Tri-Color] refer to device Documentation to troubleshoot."  Nothing in the help documentation.  The Habs is always 90% full.  Sometimes pulling the Habs and placing back in crazy wil it restarting.  When it restarts, it prints perfectly.

  I tried the ubiquitous "clean the contacts" and other instructions help generic that I saw, but those who were without help.  The "Solution Center (Yes, good)" appears and all ithas is a link to buy more ink (!).

  Someone has an idea?  I'm about to throw it through the window of stores office, given that I can't throw it out the window of HP.

  Thank you!

  Yes * I know * and I'm sorry that I forgot to come back here.  I had a major system crash and I had to reinstall a lot of drivers for my multimedia player, GPS, and printer (!).  As this occurs, the device did not return this error - touch wood.

• Problem with Hewlett-Packard-HP-LaserJet-Professional-M1214nfh-MFP

  Nice day!

  I have a problem with Hewlett-Packard-HP-LaserJet-Professional-M1214nfh-MFP, on the display is "no chain online.

  and not print certain pages. What is it?

  I'm sorry that you are experiencing this issue. I have seen this question several times here. It seems that the firmware update is the problem.

  Here is a link that you can follow to answer this question. Choose your operating system and click NEXT. Go to the FIRMWARE and download it.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=4075462&

  Let me know if it helps.

• When copying pictures on a CD, the error message "Windows has encountered a problem trying to copy this file.

  Try to copy photos on CD. I get the message "Windows has encountered a problem trying to copy this file", it comes on for each photo in the file until they are all updated. This method used to work well. Answers would be appreciated.

  You are in your folder my pictures?

  What happens if you do the following...

  Select (highlight) a group of miniature photos...

  Right-click the group selected...

  In the menu choose... Send to / DVD - RW drive...

  Transfer Photos to a CD - how to burn Images
  http://www.brighthub.com/multimedia/photography/articles/5126.aspx

  ===

  FWIW... the following freeware can be worth a try:

  CDBurnerXP
  http://www.CDBurnerXP.se/
  (works on XP / Vista / 7)

  Download CDBurnerXP
  http://CDBurnerXP.se/download.php

  CDBurnerXP - create data disc
  http://CDBurnerXP.se/help/data/compiledata