ProBook 4530 s: Windows will not start with bad secondary hdd

Similar Questions

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• I accidentally put my system as boot partition and my windows partition not marked as boot! Windows will not start! ):

  Hello

  The other day, I have been stupid, play with my windows partitions, I tried to dual-boot android 4.0 with windows, of course, as a study (this version of android has been mainly Linux). A test installation somehow fault, I put my Starter instead of windows system partition! Now windows will not start, it stays on a black screen with a sign less this sort of thing flashes in the corner.
  So I jumped in my disk windows ultimate 7, and it saysBOOTMGR IS MISSING Ctrl + Alt + Del to restart"" and if I try to install Ubuntu via live disc or USB does not start or the other, it displays the same thing.
  Can you please help me solve this problem!
  Nice day!

  After having the BIOS change, restart you your computer with the repair disc in the drive?  If so, what happened?

• Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

  Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

  I managed to install the deployments of work to the target machines. However, I expected to see the classified facility "My TestStand system" in my Start menu, but it is not. Am I misunderstanding something here?

  Also, if I do another target second deployment to the station as "My TestStand system B", all LabVIEW files in my previous installation for "My system TestStand" disappear from the directory (c:\Program Files\My TestStand system) target.

  I use TestStand Professional 4.2.1 on Windows XP and LabVIEW 2009 development station.

  Thank you Paul,.

  That solved my second problem and inspired me to look deeper for the response to my first problem. The answer lies in the tab 'distributed file","Installer properties' box 'create a program item:

  

  Wouldn't be nice if it is automatically checked by default for main sequence files? Wouldn't also nice if "Upgrade Code" was regenerated automatically by default whenever we have saved the file *.tsd under another name?

  Thanks again,

  Eugene

• Windows does not start with the second internal HDD connected

  Hi all, I recently got around a few major problems with a new buuild, but I found another issue. Windows does not start with my connected storage disk.

  hard drive 500 GB of important data that I can't save on it and need access. It is a hitachi drive, which works fine on other systems but usually works in this one. any suggestions are appreciated, thanks in advance

  fixed the problem of swapping of sata ports and reconnect the cables, thanks for the advice but

• My CS will not start with error code 16

  How can I find the serial number CS5.5 under MAC OS X if I want to reinstall it? My CS will not start with error code 16, he says: configuration error.

  Please visit the Doc KB: http://helpx.adobe.com/x-productkb/policy-pricing/configuration-error-cs5.html

• I have an eMachine EL1200 with Windows XP Home Edition. Windows will not start

  I went to start my computer yesterday morning and Windows wouldn't start up.  He continues to go to a black screen saying that Windows has not started up. It gives me options to try:

  1. safe Mode

  2 safe Mode w / network

  3 safe Mode w / command prompt

  4. last know good configuration

  5 start normally

  I tried all the and none start Windows.  Please let me know how I can fix it.

  Hi DavidMitchell,
  I would first remove all external devices from the computer and try to start again. This means that any player mp3, external drives, USB storage devices, etc.

  If this does not work and you're still stuck on these 5 options you listed above, then it might be time to use the Recovery Console.

  Please see the following thread:

  This is an article on what exactly is the Recovery Console and how to use it properly.

  http://support.Microsoft.com/kb/307654

  I hope this helps. Just reply to the results.

• Satellite P20-761: Windows will not start - it loads agp.sys then freezes

  When I pass my laptop it starts with the Toshiba logo as if commissioning, but then the screen goes black with the following message:

  We apologize for the inconvenience, but windows did not start successfully. A recent hardware of software change might have caused this... etc etc.

  Then I have a list of options to choose from:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt
  Last good known Configuration
  Start windows normally

  If I have the choice between the options of safe mode the screen goes through a list of files ending with: multi (0) disk (0) partition (1) \WINDOWS\System32\DRIVE.sys, then freezes.

  If I have the choice between the last two options simply, the screen goes black and nothing happens.

  Of I'm desperate is not to lose all the data that I have accumulated on the laptop. Stupid me not a not bother with backups.

  Discs only can I find supplied with the laptop are 'tools and utilities' and 'product recovery dvd - rom '. Seeing that I am not a technical interest, I'm afraid to try just in case I lose all my most important files.

  Help, please! Answers must be plain English as like I said I'm not really technical. Thank you. I cross my fingers.

  Sounds like something wrong with the graphics card or with the graphics driver.

  I think that you have no other choice than to use the Toshiba Recovery CD and attempt to reinstall the OS. I hope that the graphics card doesn t malfunctions.

  It's very sad, because in this case, you will lose the data on the HARD drive.
  Optionally, you can remove the HARD drive and then to connect to little via the USB port on the other computer, then you can make a backup of your data.

• Pane Windows will not start! Help please!

  I have no idea what exactly happened, but my sidebar will not start. I try to click on it through programs and all he will say is that this windows sidebar has stopped working. a problem caused the blocking of the work programme. Windows will close the program and notify you if a solution is available. I get the same message every time I try to click on run as administrator. I tried so many things, but nothing seems to work. Is it possible that I could reinstall or something? It has been so frustrating. Help!

  Hello

  If you have tried all THE above so it looks like you have a corrupted profile.

  Try these to erase corruption and missing/damaged file system repair or replacement.

  1. run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  2. start - type in the search - box COMMAND find top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  3. then run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then do-, use the hidden administrator account for the lowering your user account (the lowest level)
  APPLY/OK, then go back and reset it to the Admin APPLY/OK - this clearly allows corruption. To do this
  a couple of times. Do the same for other accounts that may be difficult. Then, if necessary, you
  can also reset your password in the accounts. Do not forget to leave your account administrator
  and others to the desired level.

  Make another Admin account with your password and use it to fix the others if necessary.
  (just to fix it with, do not use regular account, a safety valve) Always keep a spare part
  ADMIN account.

  DO NOT LEAVE THE ENABLED LSA OR USE DAILY. If it corrupts you are toast!

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  You can run the command Admin account hidden from the prompt here if
  necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you can't access your old account that you need then you can always use an Admin to migrate
  towards a new (remember to always leave an Admin account that is not used except for a test
  and fix).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Hope this helps

  Rob - bicycle - Mark Twain said it is good.

• Windows will not start since the update :( Help, please

  Windows could not start. a recent hardware or software change might be the problem

  file\windows\system32\config\system
  status: 0xc00000e9

  When I try to start the system restart that nothing happens

  When I try to restore the computer to factory settings it says that the necessary files are not there.

  My computer was working fine until I installed an automatic update from microsoft. Help, please

  For any problem with the recovery of software/process to factory settings, you will need to contact the manufacturer of your computer.
  This isn't their recovery process, Microsoft.

  Windows Update Forum:

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• SatelliteU300 will not start with power connected and fully charged battery

  I just bought a U300-13U. It works fine when charging the battery and AC is connected. However, if left to recharge completely it does not start with connected AC. Unpluging the power or remove the battery and running on AC make it work very well. Is a 'feature' to stop an overload or overheating of the battery, or just a problem with this machine. I want to run with AC and battery than both connected all the time like I did with all my other laptops.

  Any help appreciated.

  Hello Andy

  Of my friends has this small U300 and everything works well. I got it a few weeks ago to test the family Windows XP Setup and it works perfectly.

  Please test again very carefully and if the same thing happen again once I recommend you contact the Service partner in your country. They check your laptop. I have to be honest and say that describes the problem of strange sounds to me and please, don't wait too long. Contact the service as soon as possible.

  Bye and good luck!

• Windows will not start because the following file is missing or corrupt < root windows > < hal.dll windows >

  When I turn on my PC a black screen appears for about 5 minutes, then the following message: Windows could not start because the following file is missing or corrupt I can not any more access to the computer and having to turn it off.

  Hello

  I suggest that you follow the steps described in the links below and check if they help to resolve the issue.

  Link 1:

  "Invalid Boot.ini" or "Windows did not start" error messages when you start your computer

  http://support.Microsoft.com/kb/330184

  Link 2:

  IF the steps in the link 1 does not work, check the steps in the link below.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

• Windows will not start completely freezes...

  Hey!
  I had a problem that my laptop HP 7 windows does not start more... It takes time to get the Palm from windows screen and then it freezes when it gets to the office. Anyone have any idea how to solve this problem? I was thinking about the HP system recovery, but I don't know if that clears all my data or resets just windows. Don't want to lose all my data if its possible somehow. (I have the system on different hard drive recovery not on disks by the way).

  Hello

  Hard disk 1 (303) fast means hard himself is a failure and change Windows is not going to help.  Replacing the hard drive in a laptop is surprisingly easy.  Although the machine in the following link is different from yours, the process is almost identical.

  Replacement hard drive HP

  Once this is done, simply use your recovery DVD to reinstall the operating system on the new drive.

  If you do not have your restore CD, try the link below to see if you can order a replacement.

  http://support.HP.com/us-en/document/c00810334

  A possible way to try to recover your files from a disk non-boot is to follow the process described in the link below.  The CD of the Ubuntu operating system you create can launched from the CD alone (IE it doesn't have to be installed on the hard drive) and I've often found to successfully extract data even a hard failure.  When you created the CD, follow the instructions and see if you can save your existing files.

  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windo...

  Hope this works for you.

  Best wishes

  DP - K

• Laptop with Windows XP - windows will not start! __

  KIM when I start my computer, the advanced screen comes up with "run windows normally" run in safe mode, etc.  I tried this, but it does not work.  The windows logo comes with the banner running beneath the logo as it tries to start, but never does.  Any help please?

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  Fill in the blank:

  My system worked well until ___.

  If there is a problem starting, XP is configured to automatically try to start again and you can stuck in a loop of just not being able to go beyond the screen boot options.

  Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again.  You have tried them all!

  The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.

  If this is the case, you must call Options menu advanced boot yourself until you do not see the option:

  Disable the automatic restart in the event of system failure

  When you get the XP Advanced Options correct start menu you want to see, he has options on it like these:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt

  Enable Boot logging
  Enable VGA mode
  Last good Configuration known (your most recent settings that worked)
  Directory Services Restore Mode (Windows domain controllers only)
  Debug mode
  Disable the automatic restart in the event of system failure

  Start Windows normally
  Reset
  Return to OS Choices Menu

  You need to choose in this menu is the option:

  Disable the automatic restart in the event of system failure

  Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.

  If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.

  If you miss the window of opportunity F8, you must try again and start pressing the F8 key with more urgency (earlier and more frequently) until you see disable automatic restarts on system failure, and then select it.

  You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.

  Answering queries and results report of the disable automatic restart on system failure screen and you can decide what to do next.
  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• Computer will not start with Windows. I get a black screen and a blinking cursor.

  Windows XP Home Edition startup problem

  I have Windows XP Home Edition, but the computer does not start at the top.  I get a black screen and a blinking cursor.  I have an XP installation disc.  I was in the Recovery Console to recover all of the standard tasks, but nothing helped.

  Brand, model and model number of your PC?

  Are you able to get into the BIOS?
  What took place prior to this problem?
  For now, you can read this to get some ideas:
  http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm