ProLiant Microserver G7 N54L problem no display

Similar Questions

• Turn off sleep Proliant Microserver g7 n54l

  Hello

  I hope that this message is in the correct section - closest to you that I could find.

  I recently bought a Proliant Microserver g7 n54l and installed a card RS232 and Windows 7 Professional. System works well for the access control software, I installed on it.

  My problem: the microserver goes mode sleep after a few hours and must be reported by physically pressing the power button. I disabled the day before, put into hibernation and standby in Windows 7, but that DOE not help.

  Help, please?

  -are there a setting in the BIOS?

  -is it a ti software install

  Zain

  Zain, welcome to the forum.

  I want you to get the best help possible.  So, I suggest that you start a thread on this Forum.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Problems with HP Proliant MicroServer N36L...

  Please forgive me for asking this here, but I'm looking everywhere in the forum, and others that the post on all the drivers I could not find any what true troubleshooting forum, so I hope you'll forgive me if this is in the wrong place...

  I have a HP Proliant MicroServer N36L.  I upgraded the RAM 8 GB, and I have 4 X 2 to SATA drives installed, the RAID1 for two volumes of 2 TB of space.  I installed WIndows 7 Pro 64 bit.

  There is no software installed, except for the following: SugarSync customer, Air Video Server, Client TappIn and Panda Cloud Antivirus.  I keep all my photos, videos and documents on this server to facilitate access of any of my iOS devices while I'm abroad.  The video streaming server, by the way, works brilliantly, since everything is streaming is the Apple MP4 format that isn't too hard on resources...

  However, when I'm on the server and doing some of the most basic things with nothing else running (for example, copy and paste files, simply browse the contents of different folders, etc.), the server is incredibly slow.  It will just stop and after a LONG pause, resume.  Very frustrating.

  My first question - do I have installed Server 2008 R2 Standard?  I have a license for that as well.  I have no need for all of the security reporting, control, etc. otherwise than to simply share my photos and other whatnot.  So I thought that the installation of WIndows 7 Pro 64-bit would be a simpler choice.  Was it a mistake?  The installation was smooth and without a hitch, and the operating system had no trouble to install the proper drivers, etc. for the material.

  What is the best solution that will still allow these customers to run?  Should I see these "flaws"gel"with as much RAM?  It's the low power processor?

  Please forgive me for asking all these questions, but I really appreciate any insight or input I can get on this.

  Have a good night,

  Mike

  Update, I answered my own question. After a long phone call with the HP Server support, it is clear that the architecture of the N36L is pointing to Server 2008 R2. Under their recommendation, I removed from Windows 7, and server load, and now this little spitfire is fast. Very effective and works very well. I could not be more please. Don't waste your time to install any other OS MS here other than Server 2008 R2, you will not lose your time. Thank you.

• Cannot start with the USB on my hp proliant microserver, why?

  Hello!

  I had a few problems to install esxi 5.5 on my hp proliant microserver... USB keyboard, but I solved that by plugging another keyboard, an old labtec keyboard.

  Seems esxi is not compatible with logitech g510... BUT I have another problem. My server does not start with my installation of esxi usb key longer. It was also like that before I changed the keyboard, so this isn't the issue. Server starts fine and then I get the message: "'remove the disc or the media, press any key to restart" "

  It worked fine a few days ago. The usb boot works OK on my Hp workstation...

  I have a windows server 2008R2, installed on the server, but the usb boot worked fine when this OS is installed... So nothing has really changed, he just stopped wanted for a startup with USB... I loaded the default bios setting... IM lost here please help!

  IV ' e OK installed esxi 5.5 via USB stick

  Follow this link to get the usb boot: http://www.tinkertry.com/rufus-takes-2-minutes-to-create-a-bootable-usb-flash-drive-for-esxi-installation/

  Don't know yet why this work, but I'll know!

• I have problems to display the Korean characters.

  My Mozilla will display the Korean characters until last week, but now it displays them in the form of the squares with a very small number. I tried all sorts of encodings, but they are not always shown. I am sure that my computers has the support of the East for languages, it properly displays files Korean but in all my browsers (Mozilla, Explorer and Chrome), suddenly, Korean characters are displayed as squares.

  I will be grateful to those who can solve my problem, ' cuz display of Korean language is really important to me.

  I have Mozilla 20 Beta.

  The sounds that you have a problem with the font that is used to display Korean characters if this is the case in all browsers.
  
  You may need to reinstall this font.

  Other East Asian as the Chinese and Japanese languages do still work?

  • http://en.Wikipedia.org/wiki/Help:Multilingual_support_ % 28East_Asian % 29
  • http://www.alanwood.NET/Unicode/unicode_samples.html
  • http://www.Typetester.org/

• HP Microserver G7 N54L / NIC drivers

  Hi all

  I bought a HP Microserver G7 N54L and installed Windows home server 2011.

  Windows does not recognize the HP network card.

  The network card is NC107i PCI Express Gigabit Ethernet.

  A does anyone know where I can find the driver for this card?

  Thank you

  Chris

  Hello:

  Yes, I have attached below...

  Download, unzip and install manually the smbus controller driver that I tied under attachments below.

  Go to Device Manager and click the controller smbus needing drivers.  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder that you unzipped.

  Make sure that the include subfolders is selected and the driver should install.  Then restart.

• WHS 2011 OEM with HP Proliant Microserver license will not activate

  I'm building a new Server OEM WHS 2011, using HP Proliant Microserver.   I first installed one a box, entered the serial number, I get an invalid serial number message, even though I know that I entered the number is correct.

  Any suggestions are greatly appreciated.

  Hello Miked53,

  You can find Windows Home Server forums at the following location. I suggest you re-post your question here:
  http://social.Microsoft.com/forums/en-us/category/WindowsHomeServer/

• Half height half length for Proliant Microserver n36l video card

  I try to use a pci-e graphics card to fit my hp proliant microserver - 633724-421 source n36l.

  The card I have identified is a Sparkle nVIDIA GeForce GT 520 1 GB DDR3 VGA DVI HDMI PCI - E card.

  I wish only to use the HDMI output, removing the output SVGA d socket to lower the profile, then mount a suitable support. Question - this card then adapt the machine and function?

  I'm on Windows 8 server os.

  Can someone please advise

  Thanks for the reply... good point about food, I had not spotted it was only 150 watts. Video expansion card is dead in the water unless the PSU is revalued, so where you stop. I intend to use the machine for video stream to a TV using an HDMI output that would have supported the requirement audio and given a decent video resolution. May now have to settle for svga output and an external sound card or buy a media streamer and use the server at the end it was designed!

  

• my computer recently crashed and when I tried to use photoshop, then I got the message: - message - problem with display driver, temporarily disabled the improvements. Does that mean, they will return when the problem is solved?

  My computer recently crashed. A fixed it but! When I then tried to use photoshop I got the message: - message - problem with display driver, temporarily disabled the improvements. Does that mean, they will return when the problem is solved?

  Update or restore your graphics driver.

• VMware in ProLiant MicroServer Gen8

  Hello

  I just want to know if I can install any Vmware Esxi on this server http://www8.hp.com/es/es/products/proliant-servers/product-detail.html?oid=5379860#! tab features =

  I was looking in the VMware compatibility guide and didn't find it.

  In any case, is there any Posibility to run any version of esxi vmware on this machine?

  Thank you

  Kind regards

  Matias

  Yes. I can see everywhere the internet is flooded with info it works with vmware.

  And like its Gen8 so I should say vmware is normally supported by him.

  Here are some links that you ensure that it will work.

  http://Seiler.it/VMware-ESXi-5-5-installation-HP-ProLiant-MicroServer-gen8/

  HP integrates the enterprise features the new Gen8 MicroServer

  It will support up to the latest version as you can see that all custom esxi image is available for this type of material. so no question you can go forward with the same model.

• Apple Store refuses to solve my problem of display iPhone 6s

  Hi all!

  I had a bad Apple Genius bar experience. They refused to solve my problem with my iPhone 6 s screen. There are black dots (dust, debris) on the upper left corner next to the "secret" key. I have already replace display once and twice got replacement unit. But the problem is still there. (looks like a problem of design with 6 s) This time I went to apple store and they refused to do anything by saying that we have already done what we could. Now, he must live with this problem.

  My apple care (1 year) one ends in November 2016. I'm still entitled to receive support from Apple, but they will not solve the problem (maybe there is no solution because of the poor design of 6 s).

  I don't know what to do. Could you guys suggest me a way?

  Thank you!

  Best regards

  Arslan

  You can let apple know how to use their feedback channel http://www.apple.com/feedback/iphone.html

• Problems by displaying the name of the site in the header tab.

  In the header displays the word "Connection" instead of the site, although the site is already open.

  If the extension of FoxLingo is the cause of the problems then you must disable or uninstall this extension until the developer has released an update that fixes it.

  You can also temporarily downgrade to the 2.7.3 previous version.

  • FoxLingo: https://addons.mozilla.org/firefox/addon/foxlingo-translator-dictionary/versions/2.7.3

• How can I switch to windows on my Proliant Microserver Gen8 10

  Hello

  I try to get Win 7 pro to win 10 on my Proliant Gen8 microserver

  The error message I get when trying to do, it's that the onboard video of Matrox does not support win 10?

  Is it just a case of editing a video card to go beyond the issue low profile PCIE or is there to do?

  Any help would be appreciated

  Install a compatible W10 card and set it as the default video device in bios, W10 should install now.

• P10 554: problems with display power management

  It is not possible to reactivate the display (mouse movements, pressing certain keys, pressing the key) when it is turned off by the power management system. The motherboard has already been replaced by a service representative Toshiba, I even reinstalled the system, but the problem persists. The behavior is not reproducible. Sometimes it works, sometimes it doesn't.

  Anyone out there have the same problem? Is this a configuration problem or may be a hardware defect? It is already a known issue?

  Any ideas appreciated.

  Thanks in advance
  Karl Jost

  Hi Karl

  It is not easy to say, but it is possible that there is some malfunction of the equipment. In my opinion the last try to check this is to reinstall the operating system. If the problem persists there are certainly a hardware problem.

  Good bye

• Problem in display

  Guys there is a problem with the display. There are thick lines across the screen from top to bottom. You can easily notice this by turning off the display, keep your mobile under the light and observed from different angles of view. If I'm wrong, you'll feel like no there is a curtain hanging over the screen.

  It is the touch screen under the screen. It is absolutely not a problem and should not be repaired, replaced, etc.