Qosmio G - does not start, error partmgr.sys

Similar Questions

• Qosmio G20 does not start

  Hello

  Something is happening with my Qosmio G20.
  Sometimes when I connect the plug to the computer the DC IN indicator flashes orange and the pc does not start.
  A few hours later I try again and now DC IN indicator shows blue and I can boot my pc and I normally work for hours.
  It's very strange. It happens regularly. A few days shows blue and works very well and some other orange flashes of days and I can't work and I have to keep trying to connect and disconnect until it flashes blue to put on.

  Wouldn't be DC Power Charger malfunction? I've already ordered another of DC power charger to confirm, but my intuition says that is not the problem of the charger.
  I remember the 1st time that never happen... I was charging my iPod through my Qosmio and out of the House and let it load it. When I arrived home, the laptop power light flashes orange and I thought it was in hibernation mode. But after that time it started to happen.
  Before trying the new charger and reflections before sending it to the dealer?

  Thank you

  > Sometimes when I connect the plug to the computer the DC IN indicator flashes orange and the pc does not start.
  A few hours later I try again and now DC IN indicator shows blue and I can boot my pc and I normally work for hours.
  It's very strange. It happens regularly. A few days shows blue and works very well and some other orange flashes of days and I can't work and I have to keep trying to connect and disconnect until it flashes blue for setting on

  This flashing provides an error code which means that an error has been detected on the motherboard.
  It is difficult to say what could be possibly wrong power supply to electronic malfunction
  But this is only my personal opinion

  You should certainly contact someone who could verify the material and can run diagnostics tests

• Satellite C650 does not start - error PXE - M0F

  Just bought a Satellite C650, get it home and my son decided to stop the whole upward as he ran.

  Now, we get the error below:

  Check the connection of the cable!
  PXE - M0F: Exit Intel PXE ROM
  No boot device - insert boot disk and press any key.

  We received no drives, nor a manual with adequate instructions and can't find anything on the web for help.
  Toshiba closes for the day.

  Hoping that this forum could give me an idea.

  Hello

  PXE error is displayed because the laptop has attempted to boot from LAN.
  Why it does not start from the HARD drive but LAN switches?
  I think the HARD drive is defect.
  Perhaps its also not recognized in BIOS.

  Switch on and press F2. This allows you to access the BIOS where you could check if the HARD drive is recognized. I guess it must be mentioned on the first page.
  If it s not there, then it means that the HARD drive is dead and must be replaced.

  I assume that the warranty is still valid; Therefore, you should get in touch with Toshiba ASP in your country for replacement.

• HP G72 laptop: HP G72 laptop does not start, error code of disk hard when you use HP Diagnostics

  I have a laptop G72 and it will start, but Windows 7 does not start. On using diagnostic tools in the start menu, my hard drive and my departure fail their tests, with both giving me this error code:

  UCUFWF-56C81D-XD003G-60WF03
  

  No idea what this means? Help is appreciated.

  Hello

  You are welcome

  Your computer is listed as coming with a 320 GB hard drive, but you can also easily install a 500 GB HARD drive if you want a little more space - the player on the following link is an example that would be perfect for your laptop.

  Hard drive 500 GB

  The procedure to replace the hard drive begins on Page 50 of your & Maintenance Guide.

  Once this is done, simply use your recovery DVD to reinstall the operating system on the new drive - this is described in the document of HP here.

  If you do not have your recovery discs, see if you can order a replacement set using the link below.

  Order HP recovery disks.

  If you have a problem with this link, order them directly from HP.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Best regards

  DP - K

• TC - 705 crashed. does not start. error message

  My sucks TC-705 crashed.  It does not start.  error message saying lack driver DVD player.  At the beginning I was not too worried because my recovery is on a USB key.  He went through the installation process, but the re-boot did it again.  Endless loop.  I tried all repair options without success.  I went to the command prompt and run the scan and repair.  Scanned very well, she could not make the repairs.  If nothing worked the hard drive may be damaged, said a source online.  I put a new disc in, but there was no improvement.

  Where should I go from here?

  Ironfly,

  I downloaded vanilla but after I extracted it I could not make heads or tails of it.  The Readme went on and on the forums running with it but not said me something about how to launch it.  I have a question on how to launch online, but the first statement, I had was to open my WOW file.  I knew then that I had wandered in some elses universe.  After reading more later, I realized that he was playing.

  All of this is moot right now because my DVD drive and all my usb ports are dead.  There is nowhere where ever I go except in the bios.

  At this point, I don't think that there is nothing I can do.  The computer is still under warranty and I have a one year protection plan so I'll let Newegg and Acer deal with reclamation.

  I wish I could give you a hundred Bravo for all your efforts.  Thank you and all those who participated.

  unktim

• StarTech ec1pecps parallel adapter does not start, error 10

  I'm having trouble installing a parallel adapter from Startech ec1pecps on my laptop Dell inspiron 9400 running XP. I tried new drivers and the advice of the other forums, but the device driver says: "device cannot start error 10.» I received no response from Startech on it. Can anyone help?

  Hi GregSwinburne,

  ·         Have you tried to connect the unit to a different computer and check?

  The Code 10 error code is generated when the Device Manager has not enough information or the error that is upward by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  For more information, see the article:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  You can also run the troubleshooter and check if it works.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Let us know if that helps.

• Please help: Windows XP does not start error message: STOP: 0 x 00000024

  Original title: Please help: Windows XP does not start.

  Windows XP does not start, there is a message: STOP: 0 x 00000024. and run CKHDSK/F to check for hard drive corruption. But I don ' t know how to make it work? Please help, thanks.

  If this is the message you get, then you have multiple problems...

  1, xp should be on the C: drive, not F:

  Default C: is for the OS only. With xp on drive F: and you use only a hd

  then the hd must be formatted and all partitions deletion (unless there is a relocation

  the operating system is present). Install the xp installation cd, boot the pc on a cd (some PC need BIOS

  be defined for this, (boot priority), once at the cd menu, press r for recovery console, select 1

  for the C: drive, press enter for the password, type: Diskpart in diskpart, see all partitions, delete all,.

  Create one, press the key type, ESC: EXIT leave pc reboot, install xp from the cd, format it when asked.

  Read kb307654 or kb314058

• Qosmio F10 does not start system missing or damaged

  I have a Qosmio F10, and I use all the proper procedures for RECOVERY DVD-ROM PROUDCT.

  "I did all the necessary readers updates as well, but when I turn on the laptop came with an error message:" \WINDOWS\SYSTEM32\CONFIG\SYSTEM
  "Windows was not start because the following file is missing or damaged:

  So, now my computer with startup options start, but what that you choose the system starts again and again...

  What to do? Please, I beg you.

  Hmmm usually after using the CD recovery Toshiba, everything should work ok.
  I read on some computer expert sites that this problem could be linked to the hardware failure. The HARD drive or the module memory is possibly corrupt.

  I would first recommend formatting the entire HARD drive (remove also all partitions).
  Install the operating system again.
  If it does not solve this problem you could check if it is possible to install from the original CD of Microsoft XP.
  Further, you can see the memory modules. Try to remove one and use only one or replace it with a new one.

  But please note that these are just my suggestions and I m not 100% sure if these proposals will allow you to solve problems. In any case it s worth a try

• Qosmio G10 does not start

  Hello world
  I have a qosmio G10 since less than a year. It was just perfect.
  But now it won't start, but I'm unable to identify the source of the problem. (I have some experience with hardware problems, but...)

  When I push the Start button I have the ear of the DVD player running, the lights of the HD for a second and then the laptop seems to be turned on, but HARD drives do not seem to work (there is absolutely nothing on the screen, no boot screen at all). I am able to open the drive of DVD/burner to be able to exist even on the battery.

  Someone will be kind enough to share a few tips? (The FN F5/F1 key does not help)

  Thank you

  Did you hear one beep?
  This unique short beep is displayed if the device succeeded the POST (power-on-self-test) and the material is ok.
  The BIOS of the motherboard will occur always a POST during the power up, usually, this test is required to ensure its correct operation of the system and if a
  failure of the POST will identify the failure and emits a sound signal to ask the technician to take remedial action as soon as POSSIBLE.

  In your case, it s perhaps something wrong with the display. Try to connect the external monitor to the laptop.

  In addition, you can try to remove the battery and unplug the power adapter for a while.
  After several time try to connect the AC adapter again and try to start the laptop.

  If it doesn't help then I would really communicating with the Toshiba service partner in your country for the control of the laptop. Usually, technicians start some tests diagnostic and are able to locate the very fast fault.

• Re: Computer laptop Qosmio F15 does not start when the Start button / stop is pressed

  My Toshiba Qosmio f15-av201 does not turn when you push the power button, even if the lights of ac adapter & battery are both on (on). Indeed, the yellow light that is supposed to turn on the power button when the laptop is turned off does not appear. In addition, there is no sign that shows the laptop tries to start when the button is pressed, not even a peep. The laptop was recently dismantled (open) to clean the fans, who made the famous monstrous noise which toshiba qosmios are apparently well known for.
  Everything seems to be connected correctly in its correct place. Nothing seems to be damaged. So, I have no idea where I can get out of here. Pending issue.

  Help will be less appreciated.
  Thank you

  The same question again?

  Why you can't finish under http://forums.computers.toshiba-europe.com/forums//message.jspa?messageID=126963? To start the new thread new will help a lot.

• Laptop does not start: error BCD on Acer Aspire M3-581

  Hello

  Acer Aspire M3 581PTG my son has stopped booting.  At the start, immediately after the Acer logo, it now shows a blue screen with the message:

  Recovery

  Certain required information does not appear in the data of Configuration startup file. File: \BCD Error code: 0xc000000d

  He then refers to using the tools of recovery and the media, but we cannot locate Acer recovery disks and do not remember if the laptop came with everything.  I started by using a normal 8.1 Windows installation CD and tried to use different repair options, but nothing worked (perhaps because Acer has a SSD and HDD so need a specialized repair utility?).

  We contacted Acer but just received a generic response to do a factory reset.  If anyone has encountered this error or is able to offer a solution?

  Thank you.

  Try this:

  http://itsolutionsblog.NET/solution-to-your-PC-needs-to-be-repaired/

  If you still have problems starting, I suspect a hardware failure at this point, maybe the SSD or HARD disk.

  Contact your regional Acer support service.

• Windows XP does not start error message "Windows Boot failure. Press 'OK' to repair the startup failure.

  I have a PC running windows XP and it seems to be a virus when the computer starts and arrives at the log on screen. Once I log in, the background appears saying 'safe mode' in each corner of the black screen and an error box appears saying "failed to start Windows. Press 'OK' to repair the startup failure. Then, a diagnosis of FAKE windows disk rises and scan the computer. I really need help and all the fixes involve downloading something and I can not even access my desktop please help im not a computer genius! Also I do not know the specs of my PC because I can't go to windows to get them! :'(

  I think that the difficulty with myantispyware site is to know what type of malicious software that you have?

  I have this same problem on a friends laptop - I started out in a PE environment and run a couple of different recovery CD of AV companies but the problem remains. I also tried to go back to using System Restore, but it did not work either.

  On a work computer download SuperAntiSpyware Portable version from the link below save it on a USB key. Take the USB to the infected computer. Start the computer in safe mode with command prompt. Press Ctrl + SHIFT + ESC. The Task Manager opens. Click file > new task > type explorer.exe > press Ok. Navigate to the flash drive > right click > Explorer. Locate the SuperAntiSpyware file > right click and choose Run as administrator.

  I met recently a few new malwares of thugs that are loaded in safe mode effectively preventing you to download or install anything. For reasons unknown to me from the computer in safe mode with command prompt and then run taskmgr explorer.exe prevents malware to load. This method has worked several times for me this week only. Worth.

  Superantispy-portable    < this="" is="" a="" portable="" scanner="" that="" does="" not="" install.="" it="" can="" be="" run="" directly="" from="" the="" thumb="">

• No sound (audio service does not start, error 1079)

  I have no sound on my laptop.when I have troubleshooted the program that is to show that audio service does not work when I tried to start the audio service is not starting and showing an ERROR: 1079.

  I tried several times but it's showing the same...
  is there a solution for this problem?

  Hello

  Did you change your computer?

  This error code 1079, pop when you try to start the audio service?

  Method 1:

  (a) click Start, type services.msc and press ENTER.

  (b) double-click the "Windows Audio" service

  (c) click on the tab to open a session.

  (d) click Local System account, and then click OK.

  (e) right click on the "Windows Audio" service and then click Start.

  (f) follow the same steps for the service "Windows Audio Endpoint Builder.

  (g) check if the problem persists.

  I suggest you follow the link and check.

  Services do not start, and you receive an error 1079 on a computer that is running Windows Server 2008, Windows Vista, Windows 2008 R2 or Windows 7

  http://support.Microsoft.com/kb/2478117

  Method 2:

  I suggest to uninstall the sound card in Device Manager and then reinstall it.

  Follow these steps:
  1. click on start and then type devmgmt.msc in the start search box and press on enter.
  2. from the list of devices, expand sound, video and game controllers.
  3. right click on the sound card, and then click on uninstall.
  4 restart the computer.

  After restarting the computer, sound card get installed automatically. Update the drivers manually for your sound card.

  Make sure that you have installed the Windows

  Method 3:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

• Series USB drivers does not start error: "this device cannot start. (Code 10) »

  Hello

  I have a usb_dev_serial.inf of TI and a catalogue of security usb_dev_serial_amd64 and a folder containing the amd64
  the DLLs below.  When I used the Add Hardware Wizard to load the .inf, properties of the pilot were "this device cannot start. (Code 10)"
  Does anyone have a suggestion?
  Thank you
  Larry

  Hi Larry,

  Thanks for posting in the Microsoft Community Forum. According the description, I understand that the USB device does not work, rest assured that we will do our best to help you with this problem.

  Answering the question that helps us provide the best solution:

  1. it worked before?
  2 have had any changes made to the computer before the question?

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

  Try the following and see if it helps.

  Method 1:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers:

  http://support.Microsoft.com/kb/943104

  Method 2:

  Install the latest driver for USB and check if that helps.

  To do;

  a. click Start, type devmgmt.msc in the start search menu.

  b. right-click on the USB device and click on Update driver software.

  Updated a hardware driver that is not working properly:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3:

  Try connecting to another USB port and check if it helps.

  Hope this information helps. If you have any other questions feel free to respond and we would be happy to help.

• Spooler services printing does not start, error Code 1053

  Original title: Error 1053

  Hello

  my print spooler services do not start. Any help appreciated.

  Hi Paul,.

  Thanks for posting your query in Microsoft Community.

  I understand that you are facing problems with the Printer Spooler service and receive the code error 1053.

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following questions:

  1. what version of Windows operating system is installed on the computer?

  2. What is the brand and model of the printer?

  3 did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest to run the printer Troubleshooter and check if the problem persists.

   

  Open the printer Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  You can also see the following article for more information:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 2: You can try running the following commands and check if the problem occurs and also to see if the printer comes back online after

  a. click the Start button, and type cmd in the box start search

  b. right click on cmd in the list programs and select run as administrator

  If you are prompted for an administrator password or a confirmation, type your password or click continue

  c. at the command prompt, type the following commands and press ENTER after each one

  net stop spooler

  and then

  net start spooler

  This will stop and restart the print spooler service. If this solves the problem of the printer is offline, please let us know.

  It will be useful. If you have any other questions, feel free to let us know. We will be happy to help you.