Question of RV042

Similar Questions

• Cisco RV042 questions

  Hi all

  I installed our first RV042 router as I am getting a little sick of the mediocrity of the game with Zyxel and hope to use for all of my clients in the future.

  We have a problem where every morning when the user arrives to work there seem no internet. The isp said it is fine and more but no one can work, restart the router solves the problem. We use only wan1 and have installed the latest firmware, but get this question. I swapped the router with another brand and it sounds great. It is as if something expires and stops the router to work

  Someone at - there clues here please

  Thank you

  Glenn

  glenn_btn,

  My name is Ishmael. IAM with small business support team. Making excuses for the question about your RV042. I found the best solution to solve the problem of internet connectivity is by disabling the Network Service detection. Now if you were to look at your logs you would see THAT NSD cannot connect. Reason for that this router will give you this message is because when there is no connection detected for your inactive WAN (in your case WAN2) router sends then an error message down your WAN1. To disable the NSD, simply go to the system management > DUAL WAN settings and uncheck the box to turn it off completely. Don't forget to activate this feature, once you decide to make another connection to WAN2.

• RV042 Question of static routing

  I am currently using RV042 in the two-WAN backup mode. However, I tried the redundant option and think it's to give me more bandwidth and better performance than only the WAN.

  My problem is that in redundant mode, I am unable to use a few sites that I use on a regular basis. One of the sites is our Web Timesheet hosted service and their website will just crazy when I try to access the router set up in redundant mode. I am still not able to connect to their site, and it is important for my daily work.

  My question is - can I configure static for some sites routes so that the router knows he must access them through my WAN alone? For example, if my site of timesheet software is 123.123.123.123, and my favorite WAN gateway is 68.68.68.68, I can the router only to access this site through the specific gateway, even if the router is configured to use either WAN?

  I tried static routes and it doesn't seem to work at all.

  For example:

  Site: 123.123.123.123

  SM: 255.255.255.0

  Gateway 68.68.68.68

  When I save it and run the tracert to 123.123.123.123, it passes through the other door, and not that I mentioned here.

  Any tips are appreciated.

  Thank you
  Alex P.

  If your help it balance mode, go to system management support and scroll down to protocol binding.  Chances are you're going to a site secured with the two beginning of work and the site sees a connection with two upcoming ip home addresses and interrupts the connection.  You can perform a binding protocol for all your https traffic out a wan for all your network ip addresses and this should solve the problem.  You can do it for mail and other protocols that would be stripped by the dual wan.  I hope this helps.
  

• VPN IPsec on Question RV042

  I have two routers, A and B, which have a VPN between them (via internet).  If my interpretation of the VPN is correct, the traffic should be routed acorss the VPN tunnel only when a client on A LAN router seeks to achieve a customer or a resource on the B LAN router, or vice versa, correct?

  Traffic destined to a resource outside the LAN should be routed on the router WAN, correct?

  I ask this question because I have programs (who has access to the internet) who are behaving badly when the VPN tunnel is enabled between the two routers.  When the tunnel is not enabled, there is no problem.

  Hello Matt, when you use a tunnel from site to site between router RV0XX, it is a "split tunnel". The router is supposed to support wildcard masking (complete tunnel), but it's a different configuration.

  That being said, your normal circulation is described. Local traffic from Source A ask local traffic to Destination B will use the tunnel, but the local internet traffic to each router will be local to the respective location.

  -Tom

• Cisco RV042 VPN hub and spokes, connecting spokes question

  Hello

  I have a few Cisco RV042 router and VPN links them with a hub and spoke topology.

  Each speaks VPN works, they manage to connect to the platform.

  The hub can see each VPN active rays.

  A computer under the hub can connect to a computer in any talks.

  A computer under any talks can connect to a computer running the hub.

  Which works very well.

  Now, what I really need, is to connect computers under a RADIUS to connect to computers under another spoke.

  It don't work.

  Current configuration of LAN:

  HUB IP / mask: 192.168.0.1 / 255.255.255.0

  Spoke1 IP / mask: 192.168.1.1 / 255.255.255.0

  Spoke2 IP / mask: 192.168.2.1 / 255.255.255.0

  I was wondering if the Cisco RV042 can be configured to allow that and HOW?

  If we can not do, should what other router I use as a hub? Should I change the rays as well?

  Thank you and have a nice day

  Hope that this document can point you the right direction.

  https://supportforums.Cisco.com/docs/doc-12534

• RV042 connectivity

  Hello.

  I recently flashed my firmware version RV042: 1.3.12.19 - tm

  I am now affected intermittently Ithe nternet connectivity issues. Whatever site I visit, it is not uncommon to discover:

  • missing web page elements (e.g. images)
  • long load times

  TROUBLESHOOTING

  So far I have tried:

  • (hard and soft) reboot the RV042 several times
  • connection of different computers (PC/Vista, macBook/OSX) for the RV042
  • change the physical connection to a different port (1-4)
  • reviewing the configuration of the router (currently the installer with a DMZ. For testing purposes, I tried to disable the port DMZ.)

  The result is always the same, no change.

  FRAMEWORK

  • the RV042 unit is less than 1 year (bought new)
  • the problems started right now that I have updated the firmware of the device

  I'd like to go back to the original version of the firmware: 1.3.12.6.

  Everyone knows this?  Any thoughts on how I can fix this?

  @ all those who encounter this problem

  SYMPTOMS

  For me, I've lived intermittently / randomly:

  > long time for loading web pages

  > missing web page items

  SOLUTION

  Router Linksys/Cisco RV042 firmware version 1.3.12.19 - tm, contains an error that prevents it from automatically setting the MTU size.

  To correct the problem, I took advice of sk8erboi {thanks sir!} and changed the MTU to auto to manual (1500bytes).  After the change is made, I restarted the whole network (PC, router,...).  It has been about a week since the change, and everything works well again.

  ADDITIONAL NOTES

  The Cisco/Linksys documentation incorrectly States that the MTU is set from the menu option next: Firewall > General > MTU

  Here you can find the MTU auto/Manual:

  Setup > network > WAN connection Type > scroll to the bottom of the page

  As already mentioned, I was contacted by two different employees CISCO/Linksys and they made it clear that they will offer no help without a TAC: "I suggest you open a Tac case. You must have a valid contract with Cisco TAC prosecute. »

  Given that it's Aussie an easy solution, I'm surprised (and disappointed) that they do not say: "there is a bug, move the router to manual MTU"

  FRAMEWORK

  -My RV042 unit is less than 1 year (bought new)

  -the questions began at the present time I upgraded the firmware of the device to version 1.3.12.19 - tm

  -my router is configured as a WAN with DMZ, in other words, no Dual WAN

• RV042 Port forwarding stops working when the firewall is turned on

  Hey all,.

  I have an on a single WAN RV042 router and internal network. I have configured port forwarding as follows:

  HTTP[TCP/80~80]->10.0.0.6
  HTTPS[TCP/443~443]->10.0.0.6
  IMAP[TCP/143~143]->10.0.0.5
  IMAP SSL[TCP/993~993]->10.0.0.5
  SSL[TCP/587~587]->10.0.0.5 SMTP

  Everything works fine when I have the firewall turned OFF. However, when I enable the behavior is erratic. 1 of 10 attempts to connect to ANY port transmitted works. Almost all attempts at expiration time.

  Note that this happens even if you only use the default firewall rules (which must be circumvented by the port translation I've read in other posts).

  My second try was to create rules to Firewall manually, the substitution of the value default ones. I tried to add source WAN1 rules (where is my connection) to the ONE and UNIQUE IP on each port. Nothing seems to work.

  I don't know what I'm doing wrong, it's really bugging me. I had to disable the firewall if we can access our servers from outside the office. It shouldn't have to do.

  Do you know what I might try?

  Best regards

  Theo

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• Subnetting RV042

  Hello

  I'm trying to implement a subnet 2 with two routers RV042. A router will act as a bridge and the two WAN ports will be used by two different isp connection. The first router (gateway) IP LAN will be 192.168.0.1/24.

  I also want to set up another router behind router modem with different subnet 192.168.1.X/24. And I would that the customers of the 192.168.1.x subnet that you want to use the internet through the gateway router and the 192.168.0.x subnet clients to access resources on the 192.168.1.x subnet. I am able to do it with two RV042?

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• RV042/RV042 file sharing

  Cannot access shares on the remote computer. Mapping remote West works digitized NAS. Ping works. Print shops. JuUST impossible access shares via: \\10.10.197.2\sharename RV042 Firmware Version: 1.3.12.19 - tm of advice?

  Thank you, but I can write a few pages of queries on how to Word a question on this help page for Cisco.  In fact, I solved the problem by activating "Netlogon Service" on the machine, on that the shares have been. (Vista) If you go to the Windows Firewall setting, change parameters, exceptions, make sure that the Netlogon service is checked. I unchecked, share disappeared, checked, managed to reconnect.  Thanks for everyone to research.

• Setting up VPN - RV042 v3 issues

  Hi guys,.

  I just bought a version of Cisco/Linksys RV042 3 and having difficulty getting my Macbook Pro running IPSecuritas to establish a VPN tunnel.

  I get a message "Error - IKE - no message should be encrypted" in the journal of connection IPSecuritas. It will keep retrying which results in the same error. Finally, it gives just straight up.

  I'm sure that I have the settings on the router and configured in the same way Macbook of VPN end.

  Here is a screenshot of the RV042 configuration page. Any input would be greatly appreciated, thanks:

  

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• Connection from gateway to gateway RV042

  We have 2 Rv042, one in my office and the other in my home... office, we have IP static and at home No... question is can I connect the two RV042?

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  * Do not forget to give a 'congratulations '. Thank you!

• RV042 and WAG54G2

  Hello

  I have a dual WAN RV042 router and an ADSL modem WAG54G2. I would like to connect the two, but I am facing difficulties in obtaining this configuration works correctly.

  Basically, I connected the ADSL modem for the RV042 through the WAN interface and setup of the interface WAN on the RV042 using a static modem IP address, as if it were a normal PC connected to the modem. With this configuration, PC connected through the LAN RV042 isn't able to get internet connection, even if the modem is connected (I tried to plug a laptop computer directly into the modem and it works great).

  I also tried to configure the WAN interface to get an IP address dynamically (and started the DHCP of the modem), but also, it does not work.

  My question is, are there special measures for installation that I have to do on the WAG54G2 or the RV042 to get this installation work.

  Thank you and thank you for your help.

  In this case, I would say that you have configured the RV042 router mode instead of the gateway mode.

• backup smart link does not not in RV042

  I'm in the mess I have configured RV042 in backup of secruit BI (primary/secondary links), but the question is when primary folds secondary does not gets to the top. for this I hv to remove manually main link only the cable then secondary stand... Vica-versa.

  I bought this router for auto backups but if I hv to display manually the same I was mistaken.

  is thr any soluton for that.

  NET detection, I chose the HOST ip. that is my server ip address.

  Pls help me guys. I can provide more details if necessary.

  Hi, paritly problem solved when smone told me to delete connection in Setup...

• Cisco RV042 cannot create a simple VPN?

  Hello

  I'm confused because I'm trying to set up a simple VPN (client of the bridge), but I can't!

  A SSL VPN or an IPSEC VPN, whatever...

  The RV042 firmware is up-to-date, and I try QuickVPN as a customer vpn (also updated...)

  My configuration details:

  I'm at the: 192.168.2.14/24

  My RV042: 192.168.2.250/24

  And the VPN intend to connect to: 192.168.4.x

  I am currently in testing... that's why I use private IP...

  Customer gateway

  Add a new VPN group Tunnel ofgroup VPN Group No. 1 Name of the tunnel: VPN TEST Interface: WAN1WAN2 Activate:

  Configuration of local groups Type of local security group: Range IPSubnetIP IP address: 192.168.4.0 Subnet mask: 255.255.255.0

  Remote Client installation Remote client: Domain Name (FQDN) Email address (USER FQDN) Client Microsoft VPN XP/2000 Domain name: Microsoft.com

  IPSec configuration

  Input mode:	IKE with preshared key
  Group of the phase 1 of DH:	Group 1-768 bitGroup bitGroup 2-1024 bit 5-1536
  Encryption of the phase 1:	DES3DESAES-128AES-192AES-256
  Authentication of the phase 1:	MD5SHA1
  Phase 1 time in HIS life:	28800 seconds
  Perfect Forward Secrecy:
  Group of the phase 2 DH:	Group 1-768 bitGroup bitGroup 2-1024 bit 5-1536
  Encryption of the phase 2:	DES3DESAES-128AES-192AES-256
  Authentication of the phase 2:	MD5SHA1
  Time for phase 2 of HIS life:	3600 seconds
  Pre-shared key:	123456

  so far, nothing fancy... Ok?

  So I create my username for the test:

  VPN Client Access User name: New password: Confirm the new password: Allow the change of password: YesNo. Active: DTSInfo-online Active

  The user is created and activated...

  For the test, I have disabled the firewall (router + windows 7).

  A dnow, when I lunch the QuickVPN client:

  

  Then, when I have lunch:

  > Connection...

  > Activation of policy...

  > Verification of network...

  > The remote gateway is not responding. You don't want to wait? [NO]

  > Disconecting from the server...

  This means that, after activation of the policy, I am connected on the router (user status: active). But when he check network... I am offline!

  There is the newspaper of the RV042:

  dec 18 12:57:50 2012	The VPN log	description of the additional connection (qknips1)
  dec 18 12:57:50 2012	The VPN log	listen to IKE messages
  dec 18 12:57:50 2012	The VPN log	forget the secrets
  dec 18 12:57:50 2012	The VPN log	loading of the secrets of ' / etc/ipsec.d/ipsec.secrets'
  18 12:57:57 dec 2012	The VPN log	(qknips1): removal of connection

  If I'm signed for 7 seconds... Why?

  Can someone help me?

  When I try with the built-in Windows VPN client, newspapers are filled just more... ^ ^

  Help! hour

  Thanks (and sorry for my bad English ^ ^)

  Hello

  Please use our forum

  Hi Skip my name is Johnnatan and I'm part of the community of support to small businesses. I ve seen your post and I see you are using Windows 7 and that you disable your firewall to test your connection. A configuration of the computer and the router must be in order to solve your problem.

  Computer

  As you use Windows 7, you must enable the Windows Firewall and create 2 rules, also make sure that Ipsec communication is allowed, you can follow these steps:

  http://www6.nohold.NET/CiscoSB/Loginr.aspx?login=1&PID=2&app=search&VW=1&articleid=2922

  Router:

  Go firewall > basic settings and

  Disable: Block WAN request

  Enable: Remote Management

  Go to VPN > VPN Passthrough and make sure everything is activate.

  I hope that you will find this answer useful, if it was satisfactory to you, please indicate the question as answer. Please note post you consider useful.

  Greetings,

  Johnnatan Rodriguez Miranda.

  Support of Cisco network engineer.

• A problem in the RV042

  Hello.
  I have a problem in the RV042.
  Lose the configuration and return to the fixed plant.
  With out 4.2.3.03.
  That is what it is? Please, I beg you!

  Hi Alex

  I suggest you:

  • Manual resets to factory settings and re-flash latest Firmware 4.2.3.03
  • If not help, go to 4.2.2.08
  • If this is no help and that your unit is under warranty, open the service request to SMB Support Center

  Or you can describe something more on this topic (when it starts? what happen before question starts? what configuration is default factory reset? by lost or by random device power restarts?) and maybe we can help you more.