RV042 and WAG54G2

Similar Questions

• RV042 and exchange 2010

  I bought a RV042 to take advantage of the second internet connection, that we put in place.  Port forwarding for the exchange server is currently managed by our main DSL modem/router.  After spending some time by configuring the new RV042, I tried to implement yesterday.  I changed the setting of the DSL modem/router to bridge and changed the IP address so that it does not enter into conflict with the new router.  I unplugged and plugged the cables and I went back to my workstation.  I opened a browser and the internet was not working.  I pulled out my phone and sent an email of phone to my computer and it worked.  Then I tried to send an email from the workstation to the phone.  He came back not available immediately, and then I lost the connection to exchange server.  He began asked for the password to connect and acted as if I was outside the tent to connect through all the pseudonyms known to our mail server.  I even restarted the server of mail without success.  I ended up having to remove the RV042 and reset the modem/router DSL to the old settings back to work.  Anyone can shed light on what I might have missed in RV042 settings?

  Some people are using the protocol binding to bind SSL (port 443) to one of the WAN of RV042 port can work around the problem of authentication with Exchange failure.

• RV042 and QuickVPN?

  I just bought a RV042 and am in the middle of the installation of a client. They have a small office with a couple of servers but they need about 10 remote engineers access to the servers. I was able to configure and get PPTP to work, but I understand that it supports up to 5 PPTP sessions. I then tried to configure the QuickVPN Client/VPN access. By the newspapers, it seems that he connects, but fail the test "ping on the remote VPN server. Here is the log of the VPN client.

  2010/09/10 07:47:13 [STATUS] OS Version: Windows XP
  2010/09/10 07:47:13 [STATUS] Windows Firewall is DISABLED
  2010/09/10 07:47:14 [STATUS] a network interface detected with the IP 192.168.77.106
  2010/09/10 07:47:14 [STATUS] connection...
  2010/09/10 07:47:14 [STATUS] connection to a remote gateway with IP address: 192.168.26.55
  2010/09/10 07:47:17 [STATE] remote gateway has been reached with https...
  2010/09/10 07:47:17 [STATUS] commissioning...
  2010/09/10 07:47:25 [STATUS] Tunnel is connected successfully.
  2010/09/10 07:47:25 [STATUS] verification of network...
  2010/09/10 07:47:29 [WARNING] failed to do a ping the remote VPN router!
  2010/09/10 07:47:30 [WARNING] failed to do a ping the remote VPN router!
  2010/09/10 07:47:31 [WARNING] failed to do a ping the remote VPN router!
  2010/09/10 07:47:32 [WARNING] failed to do a ping the remote VPN router!
  2010/09/10 07:47:33 [WARNING] failed to do a ping the remote VPN router!
  2010/09/10 07:47:34 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2010/09/10 07:47:37 [STATUS] disconnection...

  What I am doing wrong. I have done some research on the web and consider it to be a common problem, but have not seen a resolution. Some believe that port 500 is blocked, but I am currently connected directly to the port of my PC WAN1. PPTP works with this configuration, but not QuickVPN.

  Thank you

  Do you have "Block WAN Request" in the firewall of the router settings turned off? Otherwise, please disable this option

  and give QPVN to try again.

  Thank you

• Site to Site VPN between ISR4331(Data Center) and 25 branches with RV042 and dynamic public IP address

  Hi, we just got router ISR4331. We will use this router to our datacenter as pummel hub. Not to mention that it will be the static IP address. Our goal is to connect 30 small offices to the Datacenter by VPN site-to-site. All of our offices a RV042 router and DSL connection, so dynamic public IP. How to accomplish this task. Before the VPN connection is stable and the need not to configure tunnels frequently.

  Thank you

  GM

  Hello

  Please check the config below:

  HUBS:

  crypto ISAKMP policy 1
  

   BA 3des
  md5 hash
  preshared authentication
  Group 2
  life 86400
  crypto isakmp secretkey key address 0.0.0.0 0.0.0.0 (Having said that the dynamic router HUB remote routers have public ip address)
  Describe your valuable traffic. Note that I have sepcified for both tunnels, but basically, it will be the same for the rest out for the destination. For example, I used 192.168.1.0/24 and 192.168.2.0/24. You will need to replace it with your existing installation.
  TUN1 extended IP access list
  ip permit 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
  TUN2 extended IP access list
  ip permit 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
  Create your strategy to Phase 2
  Crypto ipsec transform-set esp-3des esp-md5-hmac TS
  card crypto S2STUN 1-isakmp dynamic ipsec HUB_TUN
  crypto dynamic-map HUB_TUN 10
  

  86400 seconds, life of security association set

  game of transformation-TS

  match address TUN1

  !

  crypto dynamic-map HUB_TUN 11

  86400 seconds, life of security association set

  game of transformation-TS

  match address TUN2
  Now apply the card encryption to your WAN interface
  gi0/1 interface
  card crypto S2STUN
  Now configure on your remote routers
  Remote router 1
  crypto ISAKMP policy 1
  BA 3des

  md5 hash

  preshared authentication

  Group 2

  life 86400

  !

  ISAKMP crypto secretkey key address x.x.x.x (replace with your public ip address of the HUB)

  !

  TUNNEL TRAFFIC extended IP access list

  permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS

  !

  crypto card TUN_TO_HUB 10 ipsec-isakmp

  defined peer x.x.x.x (replace with your public ip address of the hub)

  game of transformation-TS

  match address TRAFFIC TUNNEL
  !

  gi0/1 interface

  card crypto TUN_TO_HUB

  Remote router 2

  crypto ISAKMP policy 1
  
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  life 86400
  !
  ISAKMP crypto secretkey key address x.x.x.x (replace with your public ip address of the HUB)
  !
  TUNNEL TRAFFIC extended IP access list
  ip licensing 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac TS
  !
  crypto card TUN_TO_HUB 10 ipsec-isakmp
  defined peer x.x.x.x (replace with your public ip address of the hub)
  game of transformation-TS
  match address TRAFFIC TUNNEL
  !
  gi0/1 interface
  card crypto TUN_TO_HUB
  HTH.
  Evaluate the useful ticket.
  Kind regards
  Terence

• RV042 and VPN IPSEC (Witopia)

  Hi guys,.

  I recently bought the RV042 using WITOPIA - a VPN provider.  I'm a little lost with the config.  On the side of VPN, I have a server name, login and password as well as a pre-shared IPSEC connectivity.  If I run the client on my PC, it works fine but if I try to configure it on the router it does not connect.  I don't see anywhere to store a password in the interface.  I can configure the preshared key, the server name and the username very well but there is nowhere a password.

  Any advice from people more experienced than me would be appreciated.

  Thanks in advance.

  RV042 does not support xAuth for IPsec VPN, so you have to disable the option of password on Witopia and use only the pre-shared for IPsec authentication.

• RV042 and Windows 7 w / QuickVPN cannot connect

  I have a RV042 are we able to access with XP using the QuickVPN client, but now we have added a laptop running 7 Home Premium 64-bit.  I downloaded the most recent client (1.3.0.3), run it in compatibility mode (Windows XP, tried the SP2 and SP3), you router status indicates I'm online, but the client gets in regard to verification of network, then information windows appears which States: "the remote gateway is not responding.  You want to wait? »

  I also tried the VPN Client built into Windows without success, the connection failed with the error number 800.

  Looking for any assistance with this.  I'm sure its with Windows 7, as the XP boxes have no connection problems.

  Thanks in advance for any help,

  Dan

  Fast VPN is not yet supported for windows 7.  The 1.4.X.X release will support this and will be published shortly.  Sorry, I don't have a date for this.

• RV042 and smtp

  I use a bag of mail service and I need port of port traffic before 25 in my server and restrict who I let in a couple of lines.  When I install by sending just let everyone through, when I disable redirection and set rules in the firewall, then I get nothing.  It can't be that big of a deal I know not, I do not take the right approach, then someone please help me w / who?

  You would need a rule and two access rules to set up port forwarding.

  The first rule of access to the GUI is to refuse everything, and the 2nd access rule is to allow the IP range you want to that they have access to the mail server.

• Wireless and VPN RV042 router WRT54G

  Respected member, please help if you can! I have an ADSL with dynamic connected with the wrt54g router, I recently bought RV042 and want to connect the wire coming from wireless with ports. so, basically, I want to use RV042VPN for help after the router, is there a way I can use vpn behind with port using RV042 router wireless

  I can't be able to connect to the vpn as he seeks is not an ip or WAN/LAN.

  It may be possible if you're lucky. But I highly recommend not to connect the RV042 after the WRT. A VPN server must always have a public IP address. Running a VPN server behind a router NAT (such as WRT) makes it extremely difficult and often it won't work at all. Connect the RV042 directly to your modem, configure it to your internet connection. In this way the RV042 has the public IP and VPN should become much easier. Then implement the WRT as simple access point in your network by changing the address LAN IP of 192.168.1.1 to 192.168.1.2, disable the DHCP server, and connect a LAN port of the WRT on a LAN on the RV042 port.

• RV042 VPN devices and iOS4.2

  Hello

  I have problems with the VPN between RV042 and iOS4.2 devices (iPhone/iPad).

  First question is ' is it possible at all the.

  Second question is 'how '.

  --

  I configured the tunnel group and created for the VPN user. In my Windows XP-laptop QuickVPN seems to work very well.

  But when I try to connect with iPhone or iPad (3G) I'll get a message like "the server is not responding.

  RV042 journal, I found the following lines:

  Dec 10 13:09:29 2010	The VPN log	Initial message of aggressive Mode [iOS_device_public_IP], but no (wildcard) connection has been configured
  Dec 10 13:09:29 2010	The VPN log	[Tunnel negotiation of Info]< responder="" received="" aggressive="" mode="" 1st="" packet="">
  Dec 10 13:09:29 2010	The VPN log	Useful load of Vendor ID received Type = [Dead Peer Detection]
  Dec 10 13:09:29 2010	The VPN log	Ignorant Vendor ID payload Type = [Cisco-unit]
  Dec 10 13:09:29 2010	The VPN log	Ignorant Vendor ID payload Type = [XAUTH]
  Dec 10 13:09:29 2010	The VPN log	Vendor ID payload ignorant Type = [draft-ietf-ipsec-nat-t-ike-02_n]
  Dec 10 13:09:29 2010	The VPN log	Vendor ID payload ignorant Type = [draft-ietf-ipsec-nat-t-ike-02]
  Dec 10 13:09:29 2010	The VPN log	Payload Vendor ID received Type = [draft-ietf-ipsec-nat-t-ike-03]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [9909b64eed937c65...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [80d0bb3def54565e...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [4d1e0e136deafa34...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [439b59f8ba676c4c...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [8f8d83826d246b6f...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [4df37928e9fc4fd1...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [4a131c8107035845...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [4a131c8107035845...]
  Dec 10 13:09:29 2010	The VPN log	Regardless of the Vendor ID payload [4a131c8107035845...]

  Any ideas what's happening?

  RV042 does not support the iPhone VPN connection.

  Here is the list of what iPhone supports:

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/iPhone/2.0/connectivity/guide/iPhone.html

• Why users need to disconnect and reconnect to the VPN to RDP?

  Most of the time our VPN works perfectly, but sporadically users must reconnect to the VPN to use remote desktop. Is that the user can log on to the VPN and access to things like network drives, but not other features like RDP. If they disconnect and then reconnect to the VPN, poof, everything works fine. No matter if it is minutes or hours in the VPN connection, it still requires reconnection. It seems that it is always on the second attempt at the nick of this post point called 'the second time's a charm

  We are using RRAS in SBS 2008 and the problem is multiple users tempting to VPN in XP and Win7 machines. We replaced the switches (now using Dell Powerconnects) and the router (now using Cisco RV042) and the problem persists.

  Suggestions or responses are greatly appreciated.

  Hello

  The question you have posted is related to Technet and would be better suited to the Technet community. Please visit the link below to find a community that will provide the best support.
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• RV042 to AG241V2 VPN static IP to dynamic IP to AG241V2 RV042

  Hello!

  I have correctly configured my VPN gateway Gateway inserting the real IP address on my AG241V2 so no problem, the VPN works.

  However, AG241V2 is not on a static IP address if I have implemented a dyndns account and can ping my domain name successfully to get the IP address revised each change. Implemented the RV042 and AG241V2 using the service seem to be a little more difficult.

  My RV042 is grateful properly the IP address through a DNS lookup bu I can't get an updated VPN in place. My journal RV420 VPN gives the following message.

  31 Mai 13:10: 17 2013	The VPN log	Launch the main Mode
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation Info] > Send main initiator Mode 1 package
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 2nd="" packet="">
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation Info] > initiator send Mode main 3rd package
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 4th="" packet="">
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation Info] > main initiator Mode to send 5 packs
  31 Mai 13:10: 17 2013	The VPN log	[Tunnel negotiation Info] > initiator receive hand Mode 6 Pack
  31 Mai 13:10: 17 2013	The VPN log	Main mode peer ID is ID_IPV4_ADDR: '81.xxx.199.xx '.
  31 Mai 13:10: 17 2013	The VPN log	We require the peer to have ID ' @?. dnsalias.com', but peer says "81.xxx.199.xx".
  31 Mai 13:10: 17 2013	The VPN log	We require the peer to have ID ' @?. dnsalias.com', but peer says "81.xxx.199.xx".

  
  

  Please note that I oscured DNS name with? and part of the IP address.

  Can anyone help?

  Kind regards

  Malcolm

  These products are processed by the Cisco Small Business support community. (URL: https://supportforums.cisco.com/community/netpro/small-business )

• Solved: RV042 <>is QuickVPN

  Summary: If the user account on the RV042 VPN, contains special characters (other than letters or numbers) you may not be able to connect to the RV042.  The marker for this behavior will be when your password is displayed in plain text in C:\Program Files\Linksys\Linksys VPN Client\wget_error.  It seems that the password field is poorly analyzed when the command line for 'wget' is created by QuickVPN.  Three special characters I've initially included in my password of the VPN user account have been, #-the pound symbol! -Exclamation point /-oblique.  Simply remove the special characters from the password VPN user account enabled me to connect.

  I hope this information is useful to someone reading the forums.  QuickVPN has so many points of failure, I am tempted to declare "not reliable."  8 ^)

  The players in the circus of connection attempts are:

  Client side:
  MSI Wind Netbook with XP Home and customer QuickVPN 1.2.11
  Cricket in wide band with Cal - Comp A600 USB Modem

  Server-side:
  RV042 with Firmware 1.3.12.6 - tm (May 28, 2008 17.52:01)
  dyndns.org account
      
  Dave.

  Summary: Setting the MTU size to 1300 of WAN #1 (Cox broadband) and WAN #2 (Qwest DSL) allowed me to connect consistently to the RV042.

  So, I no sooner opened an adult beverage to celebrate my RV042<==>QuickVPN connection above when my next attempt was a complete failure.  I received the error "Check network" dreaded.  The wget_request_error file showed "501 not implemented" at the request of CheckIsakmp.htm.  Shit.

  If I have more problems with the RV042 and QuickVPN I buy a professional solution to my VPN needs.  My tolerance for this madness is done.

  Dave.

• Add a static route to a RV042

  I have configured the RV042 dual WAN port for backup smart link connected to two different ISPS.  The subnet behind this is 192.168.2.xxx.  I have a second router linksys Garland with the 192.168.2.250 WAN port and subnet behind it is 192.168.20.xxx.  My problem is that I have a not able to route traffic fron 192.168.2.xxx to 192.168.20.xxx.  How can I add a static route so that clients on 192.168.2.xxx can access resources on 192.168.20.xxx?

  1. the second Linksys router must be changed of gateway (active NAT) in router mode (NAT disabled) mode. With NAT the LAN behind the second Linksys will be not accessible from the outside unless you configure port forwarding.

  2. on the RV042 set up a static route for the subnet 192.168.20.0/255.255.255.0 to the gateway IP address 1921.68.2.250 on the LAN interface.

  3. Ideally, you must configure the same static route on all clients connected to the RV042. If you don't want to do this, you must configure the firewall on all clients on the RV042 accept ICMP redirect messages. This is important because otherwise all traffic from 192.168.2. * to * 192.168.20 would be sent to the RV042 and from there to the second Linksys that is unnecessary and could create a bottleneck.

• New mapping RV042 Shrew soft client NAT - t

  Hello world

  Because I had the fast VPN problem, so I tried the customer sweet shrew in the hope of getting the IPSec tunnel with RV042 router mode Client2gateway.

  The Shrew client, I had "Tunnel is activated" but I got established has no errors.

  RV042 IPSec log, he ended with: NAT - t: x.x.x.x new mapping.

  What it means?

  Thanks for your replies.

  Hi h.dam,

  If the tunnel is activated and the display put in place = 0, two phase errors.

  Please you found the file attached to this message "With ShrewSoft RV042" and follow all the steps and share the result with us after your tests

  Please rate this post or marked as replied to help other customers of Cisco

  Greetings

  Mehdi

• RV042 to RV320 passing

  Hi all

  As the title says I spend a RV320 since a RV042.  I want to minimize the downtime of the network and configure the RV320.  Is it possible to display the backup file Mirror.config of the RV042 and be able to create a startup.config file that I was able to load in the RV320?

  Thanks in advance for your help.

  Jon

  Hello

  The RV042 config file is encrypted is not not clear text so we can draw information, as we do not have a tools for this.

  Only way is to have access on the two router (WebGUI) so we have visibility to the RV042 configuration and configure with the RV320

  Thank you

  Mehdi