Red screen flashing interminnietly

Similar Questions

• Now 23-d044 - installed MXM video card - HP Envy screen flashes red green blue black

  Hello

  I'm a 23-d044 I wanted to do the update/install video card instead of using the integrated graphics card.  I tried two different cards, a nVidia GeForce GT 540 m 2 GB and a part of HP AMD card #707804-002.  In each case the applied heat sink was part HP #694456-001. In each case, whenever I go back to the PC and it works, the screen flashes red, green, blue, black, white to infinity. I have read these and other forums indicating that this is a fault with the GPU, but I find that is unlikely given that I tried two different cards. I thought that maybe the MXM connection on the motherboard, but on the original motherboard power connector was defective, I have since replaced the motherboard (about 2 weeks ago) with the same part number. I downloaded both the AMD and nVidia drivers the most recent for each card (while running the integrated graphics card), but not joy.  Anyone have any ideas?  Thanks in advance for the help!

  Sean

  Sean, I had the same problem too.  I finally thought to it.  Just above where the grafics card go is two connectors and one of them has a plug in there.  above the connectors, said uma_lvds, the other says MXM_LVDS.  Swap the power cord of the uma_lvds to the mxm_lvds.  This will fix the problem and you will be running.

• Screen blackBerry Smartphones Black, red light flashing

  I was downloading an application when a screen message told me to reboot to continue the installation. I pressed the Off button, but now, despite pressure on the Start button, the phone will not come alive, even if she was recently charged. There is just a black screen and the little red light flashes from time to time.

  Hi HarryTyrrell

  Welcome to the BlackBerry Support Community Forums

  By pressing the button Off is not the correct way to restart our BlackBerry device, please perform a battery pull reboot as this device while is powered on remove waiting battery for a min. and then reinsert it wait until the device take a long restart. See if that helps.

  If this isn't the case, then try to start your machine in Safe Mode and in Safe Mode uninstall your downloaded recently or that you think is responsible for this.

  KB17877 How to start a smartphone BlackBerry in Safe Mode  

   

  Try it and tell us.

  Prince

  _____________________________________________________________________________

  Click 'Like' If you want to thank someone.

  If problem resolves mark message (s) as a 'Solution', so that others can use.

• Screen flashes while taking pictures using the Auto flash and front camera on

  Device: iPhone 7 more

  iOS: 10.0.2

  Question: Screen flashes with blank white light while taking the photo using a front camera with the flash light on which is so annoying

  Note:

  After taking the photo, the photo is visible and doesn't have any problem

  I could be wrong, but I think that this is how flash works for the front facing camera.

• iMac screen flashes black in Photoshop CC

  Hello

  I am posting this as well in CC Adobe and Apple forums as I do not know where the problem lies, but I would really appreciate this problem:

  I use Adobe apps on an iMac CC brand new (still in time to get the full refund). If you use Photoshop CC (2015.5) the entire screen (not only the Photoshop window) goes black for about half a second when any icon tool exceeding a certain size of pixel passes of the tool to the pointer icon icon or vice versa.

  This happens for example when the icon of the fate of the area of the image on the menus or the dashboard or window, or when it comes in and out of the right click menu change brush size. Any situation when running the tool pointer or pointer tool. It does not always happen, but it happens most of the time, maybe the type of pointer movement has something to do with it, well it happens with fast or slow transitions.

  The problem only occurs when the brush is superior to certain dimensions - never when it is less than the critical size. The critical size may vary depending on whether the Photoshop was opened for a while or just launched (I don't know too much about). There is also an interaction with the hardness of the tool.

  Thus, for example:

  On the blur to 0% hardness tool, the screen flashes black when will top 80 pixels-never less than size. 100% hardness, it flashes from 64 pixels. Same for the Brush tool, Eraser, etc. I think it happens with any appreciable tool (don't have not tried them all).

  I use a Wacom Intuos PS and the Magic Mouse from Apple. The problem occurs at the same time if they are both connected together or separately.

  The problem occurs even when Photoshop is the only application running.

  Please help, because it is almost unusable now.

  Specifications of the computer:

  iMac, retina 4 k, 21, 5-inch

  Processor: Intel Core i5 to 3.1 GHz

  Memory: 8 GB 1867 MHz DDR3

  Graphics card: Intel Pro Iris Graphics 6200 1536 MB

  The Photoshop memory usage is set to default values:

  4500MB (70% of available memory)

  4 levels of cache

  Tile size 1024K cache

  I just downloaded and tried the oldest version of Photoshop - CS6 - available through my driver's license and the problem is exactly the same, this is not limited to a particular version of the CC in Photoshop.

• 2008 mac book pro screen flashing folder with question mark at startup

  2008 mac book pro screen flashing folder with question mark replaced boot hard drive and cable, continues to do the same.  any ideas to fix?

  Start your Mac by holding down the button Option. The should launch the window of Boot Manager where you can select the startup disk, and then click on restart.

  How to choose a boot on your Mac - Apple Support drive

• When sharing my project there are some clips that show a red screen with a camera saying error. How can I solve these clips if I can share the project correctly?

  When sharing my project there are some clips that show a red screen with a camera saying error. How can I solve these clips if I can share the project correctly?

  This happens usually when the import process was not completed. If you have the original camera card - or a copy of the computer of the map - you can probably use the re-import command (on the file menu) to fix things. In addition, it is possible that the original media is imported, but this transcoding was not. If you have chosen to optimise upon import, try to select clips in the browser and transcoding to optimized.

  Russ

• Red screen of death

  iPad Mini 4

  
  

  Last night I plugged it in to charge and this morning the screen was frozen showing the Apple logo. I did a hard reset and thought that this would solve the problem. Unfortunately, shortly after the Apple logo, I got a red screen. The iPad is in an infinite loop and does not boot.

  I tried to restore the iPad via iTunes, but it didn't work. I entered DFU mode and tried not to restore once again, no luck at all.

  My last resort is the Apple Support. I'll take it to an Apple authorized service center and hope for the best.

  What frustrates me is that I have this iPad for 2 months and it was purchased new in an Apple Store. I'm really angry...

  

  AlemaoSlv

  I understand your frustration, however electronic devices can fail for various reasons. The unit is still under warranty, Apple should take care of your problem.

  This is a user to user support forum. If you wish you share your frustration with Apple, then use their comments here, http://www.apple.com/feedback page and click the box in the matter.

• Red screen

  I dropped my iPad 2. It is out of warranty. When I tried to turn it on it started with a red screen with a battery symbol. After a few seconds, he would cycle to a gray, then black screen, then repeat the loop. It would not keep pressed power button or combination home + power or being plugged into iTunes. I left it plugged and after a while the battery symbol has been replaced with the apple logo, but the screen is still red and the infinite loop going.

  I can't find something on this error on iPads and no image like that of my screen. I have a picture but you can't post it here.

  Any help would be appreciated.

  Hello.

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

  As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo of iTunes on the screen of your device. After that on your computer, you should see the iTunes window saying that your device needs to be restored to factory settings. Click Restore.

  More info here:

  https://support.Apple.com/en-us/HT201263

  If these steps do not work, contact Apple and ask for help.

  https://www.Apple.com/support/iPhone/contact/

  If this does not help, it is best to make an appointment at the Apple store because it may be a hardware problem.

• Hi, my screen flashes during playback of movies from Netflix

  Hi, my screen flashes during playback of movies from Netflix. It happens with other applications or when I play DVD. It begins in about 5 seconds in movies and it happens about every 4-5 seconds. The screen turns white for about a second, then it shows some horizontal lines, and it goes back to normal. And after a few seconds, he begins anew. I also noticed it always happen when I move my mouse during playback of a movie at Netflix.

  My PC is HP Pavilion 17 inch. I3 Haswel processor and Intel graphics card built-in. 8.1 to win

  I've updated all the drivers, but nothing helped.

  Any suggestions?

  Thank you

  Dmitry

  Figured out. Change refresh rate of 60 Hz 40 Hz p p and it solved the problem.

  BTW, HP helpdesk is completely useless... He does not call them – at least their 'free' in India support is completely incompetent.

• Control LCD screen flashes on and outside

  Hello
  I have a 6 yr old HP w15e LCD monitor, it is quite old. But recently, it's showing strange things. Whenever I turn on the power to the monitor with or without the CPU video input, continuous screen blinking on and outside (I think there are two seconds between the two slot and power off).
  I tried different power cables, but still screen flashing. So help me to record this thing.
  Thank you.

  Hello @shan678,

  I understand that your w15e HP LCD monitor continues to blink off and off and you seek help to fix. I provided you with a few steps, you can try below:
  
  Step 1. Unplug the power cord at the back of the screen and the wall
  Step 2. Press and hold the power button for at least a minute
  Step 3. Plug the power cable in the monitor, and then to the wall outlet (not a power bar or surge protector)
  Step 4. Press the Menu button on the monitor
  Step 5. Navigate to the factory reset option and select
  
  If the steps above did not resolve your issue, you can try the monitor on a computer or other device to see if the problem persists. If not I think it would be preferable that you contact HP Support for service options.
  
  Thanks for posting on the HP Forums. Have a great day!

• Screen flashes black when playing games

  When I play the games. The screen flashes black for a few seconds then goes back and re-offend?

  After reading this description of problem a single sentence, it is not easy to tell a lot about your problem.

  Perhaps you should tell us something about your machine, pre-installed OS, display driver you are using and of course, be a bit more detail on this subject.

• Satellite M300 - screen flashes white

  Toshiba Satellite M300 on 18 months old (using Windows 7). Display has had intermittent problems. Screen flashes to a white screen. Now if the lid is moved while he was working, "white" screen completely and returns to normal when returned to 'the sweet spot '!

  Have not yet tried another monitor. Driver is up-to-date. Assuming that maybe it's a "bad connection". Use turned off with the closure of the lid that changed tonight.

  Any ideas? :)

  Hi KezRev,

  Theoretically, it could be a problem of connecting cable or internal problem display but you should test another monitor first. Just connect an external monitor to check the image here.

  If the external monitor works properly it s the LCD cable internal or visualize a malfunction. So, contact a service provider and allow technicians to check your laptop. They can fix this problem and order new parts. :)

• Screen flashing on Satellite U series

  Hello

  I have a Toshiba laptop with a weird problem.
  The screen flashes if I remove the battery, it stops.

  I put a new battery but same problem.

  Can help?

  What devices you have connected to the laptop? External monitor? USB devices?

  There may be a ground loop or something.

• 10 update, the screen flashes.

  Update Windows 7 10, (last night). My laptop screen keeps flashing and I can't use the computer at all. How can I uninstall Windows 10 & back to 7?

  I suggest you only start Win10 in safe mode. Because you screen flashes the only way to do so is in the password screen. When you're at the password screen, click the power options in the lower right. Hold down the SHIFT key and select restart. This will get you to the troubleshooting page. Once you're in safe mode, you can return to Win7. I suggest you google "Win10 starting in safe mode" and "return to Win7 from Win10. It should provide you with screenshots. I hope this helps.