Satellite A100-512 - Message appears - unplugged network cable

Similar Questions

• You are not connected to the internet! You want to work offline or try again? There is also a box with a red x and the message reads unplugged network cable.

  Unplugged network cable?

  Recently I get this message then on the line. You are not connected to the internet! You want to work offline or try again? There is also a box with a red x and the message reads unplugged network cable. It is very aggravating. Can someone tell me how to solve this problem? It might have something to do with my firewall? I recently downloaded mozzilla firefox if I could play words with friends, because IE would not work on the game.

  Hi LouisteanGriffin,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  Windows wireless and wired network connection problems

  For reference:

  How to reset the Protocol Internet (TCP/IP)

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• Huawei mobile adapter unplugged network cable. How to connect

  Huawei mobile adapter unplugged network cable. How to connect?

  You can just X that out or let it go on its own, doesn't mean that you are not yet connected.

  You press Connect on the popup of the Application.

• Unplugged network cable

  Hi all

  I was invited to take a look at an old enough box office running Windows 7 32 bit Ultimate edition. Map of oboard nVidia nForce network constantly reports that a network cable is unplugged - this isn't, of course.

  The owner told me that, once the machine has started, it must plug the router until the machine detects the connection. I brought the machine in my network and to see the same kind of symptoms, except that it may, or may not, to detect the connection to chance, no matter if I power cycle the switch from office to which it is connected.

  I tried several different cables, ethernet, mine and without changing the owner

  I found that the permutation of the speed / duplex settings on the Advanced tab in the properties of the controller to auto to 100 Mb Full Duplex causes the connection be detected until the computer is restarted. At that time, cable disconnected message returns until I exchange the speed / duplex back to auto.

  I removed the controller from Device Manager and hosted Windows redetect, uninstalled and reinstalled the driver etc.

  I have reset winsock / tcp.

  In desperation I even set up a PCI network card (Realtek, I think from memory) and to people with disabilities the controller on board - the PCI network card shows the same problem, but is slightly less willing to connect when the speed / duplex setting is changed.

  I'm sick of ideas on this one - any suggestions would be much appreciated!

  TIA

  Rob.

  You may be able to find an Ethernet card that will fit the old man.  Should not be too expensive.

• Satellite A100-033 - where to get the cable/connector for power switch?

  Hello

  I change the cable/connector for * power switch button * which connect to motherborad. If anyone no where I can get in? I tried at PC world, but they do not have cable, I am looking.

  My laptop SPAC:

  Satellite A100-033 part number: PSAANE-03J02GEN

  Thank you

  Hi rjbuz,

  I can t tell you the part number because I m not the owner of the Satellite A100, but a service provider authorized in your country can do this:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Just give them a call and ask. Maybe they can send you the replacement part. :)

• Satellite A100-495 - Intel 3945abg wireless network card cannot find wifi networks

  Greetings,

  I have some problems with networks wireless on my laptop Satellite A100-495.

  The problem is: my wireless adapter (intel / pro 3945abg) doesn't seem to find wireless networks. If I portable place very close to my router wireless (such as 1 m) - connection can be established. If I move away (~ 5 m)-no connection or 'very bad' quality and constantly broken. Other notebooks I've tried still have "very good" quality at the same range.

  This happens with other routers as well. And I can not any sign of wi - fi in my Uni (my colleagues have no problem with their machines).

  I tried to play up with some parameters. Reinstalled adapter. Downloaded the latest drivers. Nothing helps.

  A tip? Thank you in advance.

  Hello

  Something like that happened to me a long time ago.
  I used the Wlan configuration option to own Windows. For several months, I use the Intel Proset configuration utility to establish the WiFi connection!
  It works!

  In addition, I have disabled the power Wlan option in the Wlan card properties save and adjust the intensity of the signal at top. I remember, in the advanced properties, you can find the 802.11 option preamble. The value is Long and short on my laptop.

  Hey dude... Check it out.

• Satellite A100 - 02 M - missing wireless network adapter

  Hello

  My wireless was working fine yesterday, but today when I turned on there is no wireless signal.
  The switch is on, but no light on.
  And the wireless card is missing from Device Manager.

  Does anyone have any ideas how I can reinstall the Please?
  I don't know what type is the adapter...

  It's a Satellite A100 - 02M. Thank you

  Hello

  Satellite A100 - 02 M seems belongs to the PSAANE series and the Atheros WLan card driver should be right.

  The latest WLan card driver can be found here:
  http://APS2.toshiba-tro.de/WLAN/

  See you soon

• Satellite A100-049: message: AC monitor does not?

  Can help anyone, on startup, I get a message... AC Monitor not working then check the solutions... then cannot find AC monitor will be closed.

  Did you install the 3rd party applications on the Vista operating system?
  This message appears since the first start?

  CA-Vista monitor is not known to me but I studied a little and some people have suggested that this may be a Lexmark file.
  In this case, you would need to uninstall and reinstall your Lexmark printer

• Satellite A100: Norton error appears - memory could not be read

  0 x 02459962 referred memory 0x5902adf8 memory can not be read.

  This error keeps showing upwards.
  Can anyone help? He came to norton when I do a check up.
  Also, I get an error when I close internet explore tells me msvcr.80.dll is not found.

  Aside from that my laptop works ok, it is a satellite A100.

  Hello

  I think that this file msvcr.80.dll is part of the .NET Framework 2.0.
  I would try to install the version or see if you can do a repair on it via Add/Remove software.

  I studied and declined to find out why the error of Norton.
  But the address of memory does not help.
  However, it seems that you have installed something that might be a bad influence.

  Maybe a switching of the BONE at the beginning good point work would clear this issue.

• Satellite A100: Bios password appears - what should I do?

  Hello world

  Last year, I bought my toshiba Satellite A100. I never set a Bios password. Today I was working normal. Then I restarted my laptop and got the password.

  Now I can't access my laptop. Is this a common problem? What should I do?

  concerning

  No, this isn't a common problem. It s absolutely impossible that a BIOS password is stated zero part.

  In general, you will need to send the machine to an ASP for the removal of the password, but before you do, I would ask all members of your family who has access to your computer if it has put a bios password and wanted to make a joke (in this case it s not a really nice joke)

  Welcome them

• Satellite Pro A100 - PXE message appears at startup

  I have a problem and I really really really could use some help, its been listen to me for the last two days ive trawled through countless amounts of forums and web pages without success then for a last ditch attempt until I throw it out the window (figuratively) I thought I'd come here for help!

  It's a Toshiba Satellite Pro A100 model No. ' PSAAPE-00Q00KEN

  initially when I started the computer this error message came

  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit Intel Boot Agent.
  Operating system not found

  now, I managed to stop the PXE errors by disabling the Lan built into the BIOS option

  I have check and made sure it is not a disk in the DVD player to the left it doesn't have a floppy drive so it isn't that

  BIOS for some reason usually see the hard drive is a seagate 80 GB HDD Sata, but I know that its fine because it works but in my Dell laptop.
  and my Dell laptop hard drive is not seen in the Toshiba.

  Now that I read all about flashing the BIOS, but I can't because the only download I get Toshiba is one that runs when windows is running (if I can't get it to boot, how do I Flash the bios)?

  I also tried thing BIOS resseting to short-circuit the c88 under the wireless network card, but that didn't work or the other!

  Now is there anything else I can try or do give up and throw it out the window?

  Thanks in advance

  Terrakan

  Hello!

  It's really strange, but it looks like your HARD drive to the motherboard controller is the reason for this because you said that the HARD drive works in another phone.

  Can you please try another HARD drive in this notebook? If another HARD drive works the old HDD is definitely faulty and if not, I think that the motherboard must be replaced.
  So, you can determine what is exactly the problem.
  In addition, I think that there is nothing more you can do at the moment.

  Good bye

• Impossible to activate the WLAN on Satellite A100 (error message)

  HI - please excuse me if I'm missing some information here, I'm not used to dealing with computers and don't know all the technical terms!

  I use my laptop computer for 4 years and never had any internet connection problems. Use wireless this morning, and by the middle of the afternoon he had "disabled" itself. I tried to activate it (in ConfigFree) but get the message that "the question does not switch '-'Devices '.

  In detail, the three problems proposed are not the cause, none of the items are open. When I run the connectivity ConfigFree doctor, it just tells me again that my wireless connection is turned off.

  I am temporarily able to use another laptop and have tried to install the latest driver, does not. I also did a system restore to last week, but even once, he touched nothing.

  If someone could shed some light on how I can reconnect to the internet it would be much appreciated as I am only able to connect wireless to this place. If I missed any vital information, sorry! As I said, I don't really know what I'm talking about here...

  Thank you

  Hello!

  Have you checked if WLAN is actually enabled on your laptop? You can turn on or off with the switch of material that needs to be defined on and key combination FN + F8. Check this box!

  Also have a look in Device Manager if the wireless network card is installed correctly. In your case, I would also try an update of the WLAN driver.

  If you have any other questions, please let us know! :)

  Good bye

• LaserJet Pro 400 M425dn: Unplugged network Cable

  I just bought a printer LaserJet Pro 400 M425dn and tried to set up on my university network. I have a static IP address for the printer. However, no matter how to set up the printer, I see only cable disconnected in the status screen of the network on the touch screen. The cable and the wall socket is working, since I can connect to a computer using their network.

  There is no flashing lights, close the network card. Is the printer network card defective?

  The network port is part of the trainer so if defective, you need to replace the formatter.  Having said that I had one who wouldn't not connect to the network.  I don't me remember not if the link lights have been turned on or off, but he finished the port has been wired incorrectly.  The pairs have been overturned as a crossover cable, and we have done the same and connected a laptop to the port and it works.  We discovered that the laptop automatically detected the pair reversed and connected.  Not sure if this is your case, but I propose the printer to another location just to see if I get a clear link to another location.  If no link light, then I'm afraid of the trainer will need replacement.

• Startup gets "Network cable unplugged" on mini-PCI Wireless card

  I recently installed a Netgear DG834GT wireless router and now have intermittent problems connecting my Tecra 9100. If the 9100 has been off for awhile (like overnight), when I restart I get always "Network cable unplugged" for the wireless connection. Reboot several times (anything from 3 upwards) I finally get connected to the router and everything then works fine for hours. Even a quick restart at this point (that is, once that the wireless adapter is connected) does not cause a problem, but as soon as I leave the stop of the machine during a time he fails again on restart.

  There are no errors in the event log.

  I am using wireless mini-PCI cards and have already updated to the latest version of the driver.

  Any ideas gratefully received, for now every morning is a 20 to 30 minutes of rebooting frustration trying to get my connection work.

  (Running Win2K professional)

  Hello

  As far as I know, the unplugged network cable message just for LAN (Local Area connection-LAN) and not wireless.

  If you want to check this map to disable LAN in Device Manager. After starting the laptop turn on the wireless card, check the status using the FN + F8 key combination. Wi - Fi is activated after a short time, you should be able to use your wireless network.

  You can enable the option Show icon in notification area when connected. You can find it in the properties of wireless under the general tab.