Satellite C665 - Ethernet adapter has stopped working

Similar Questions

• Satellite L770 - ethernet adapter has stopped working

  Hello
  I have three laptops all connectable to my home hub, but I seem to have serious problems with the latest model, L770-13D. The signal strength has never been as good as the older models, and most recently the Ethernet adapter has stopped working. I have updated drivers on the two adapters, but it did make a difference. I recently updated my connection and I wonder if the Ethernet adapter is not configured correctly because it was working fine before the upgrade.

  I also tried almost all the tests I can do - Toshiba config doctor returned a FAILURE on the verification of the material that I did, but the device manager says that the two network cards work OK. Also, troubleshooting reports wireless adapter that it "can be a problem", the evidence seems to be directed towards a hardware problem with this laptop.

  Any thoughts?

  Have you noticed this Ethernet problem on the first day? Otherwise, I recommend you to reinstall the OS using original recovery image and test once more with the factory settings. Recovery image contains the drivers right and tested. It is also configured to be used immediately after the first start, so it shouldn't be a problem.

  Have you ever done this?

• Adapter Ethernet Thunderbolt has stopped working after update 10.11.2.

  Hello, after my update to 10.11.2 on my MacBook Pro retina 15 "mid-2015, my crush Ethernet Adapter has stopped working. It comes in the reporting system and it shows that it connected to ethernet, but in the network Panel, the State remains red and I don't get an IP address.

  My colleague who has a MacBook 2013 15 "retina Pro also has the same problem. We tried the retail adapters Ethernet Thunderbolt, but still no connection on one of our networks.

  Anyone else see this behavior?

  Same problem here on my end 2013. In Recovery Mode, the card works (good trick to know if hardware is broken). Roll back via Time Machine works 10.11.1 and adapter. Adapter and 10.11.2 relocation does not-MBP-R all my colleagues in different years work well after the update.

  BTW. : not only Thunderbolt Ethernet does not work, but the cards virtual Parallels (for shared and host-only) as well (only bridged mode works).

  So far, all the stuff has failed. And now I will notify again before the update.

• Re: Satellite L850/046 - keyboard has stopped working

  The laptop Toshiba Satellite L850/046 - keyboard has stopped working.
  Have restarted. In the box of charms, it seems ghost.

  Impossible to restore or reset as it asks password and keyboard does not work

  Hello Graham

  Sorry, but your problem is not easy to understand. After reading these two sentences, it is not easy to tell if there is a general problem with the keyboard or what.
  When you enter the BIOS settings can use keyboard to scroll through the options and tabs of the BIOS?

  Since when did you notice this problem?
  You have created a recovery media? If Yes, please try to use it and install original recovery image.

• The model name of my DM9601 To Fast Ethernet adapt is DM9601 to Fast Ethernet Adapterhas has stopped working correctly because a compatible driver is not available for this version of Windows.

  has stopped working properly because a compatible driver is not available for this version of Windows.  This is the error I get and it made my computer unable to re boot. Please help me how to set right.

  Thank youy

  Hello

  you left in the name of material on

  DM9601 USB to Fast Ethernet card; fix?

  and sorry, but I cannot find a driver for him after XP

  you are also posting in the wrong forum

  Try the forum hardware and drivers

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware?page=1&tab=all

  or contact the hardware manufacturer

  they write drivers for their products, not from microsoft

  ______________________________________________________

  try a restore of the system before this happened

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Lightning network adapter has stopped working

  Hello

  All of a sudden, my (original Apple) map network Thunderbolt has stopped working. I'm looking for advice to get it working again without reinstalling. This is the second time in 6 months that it happened, and the last time a reformatting it fixed and restore my entire user account does not restore the problem, so all signs point to something in the heart of the system and not "userland".

  Why I know that the adapter is not the problem:

  -Adapters two colleagues also do not work

  -Adapter works very well in recovery, but not once started

  What happens when I plug:

  -Lights led network switch, so a link is established

  -L' adapter remains 'red' in the network settings

  -dmesg shows:

  IOThunderboltSwitch < 0 > (0x0): listenerCallback - HPD Thunderbolt package for road port = 0 x 0 = 1 disconnect = 0

  [Start of PCI configuration]

  [End of PCI, bridges 14, 15 devices configuration]

  No obvious signs of problems.

  Steps taken to solve the problems:

  -If I delete the card of network settings, I can never add again; He simply never shown even if it is plugged in and the link light is on the switch.

  -Crushed/Library/Preferences/SystemConfiguration and restarted. Always impossible to add the interface, as mentioned above, it never appears.

  At this point, I am of ideas. Any help would be greatly appreciated.

  Thank you!

  Figured it out... it's driver Linksys USB3GIG crap that breaks the kext IONetworking signature.

  ERROR: invalid signature for com.apple.iokit.IONetworkingFamily, does not load

  After removing AppleRTL815 * from /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/ and restart, thunderbolt ethernet is back

• Satellite T130: integrated webcam has stopped working

  Hi, I have the same problem of the bellows of the question, as I looked around and I was not able to find the answer I need.
  I have a Satellite T130 and, suddenly, the integrated webcam has stopped working properly. A blue light is on, but there is no picture. What can I do?
  Thank you

  Hi mate

  I have the same problem, sometimes using my U400.
  This happens if the room is dark for the camera.
  If something like this happens to you that I recommend that you keep your finger in front of the webcam for a short period.
  After that, the image of the webcam should come back again in my case it worked.

• Satellite U300-130 - TosBtMng has stopped working after installing Nokia PC Suite

  I have the same problem too... with Toshiba Satellite U300-130.

  Bluetooth worked well enough before I installed the Nokia PC Suite for my mobile on my PC (new version 7.1.26.0 Web site).

  To be correct, as a first step, I even managed to maintain a connection between the PC and the Nokia Bluetooth and ran the synchronization of the contacts. I tried several times, but each time synchronization run ended with the message "PC couldn't get response from your Nokia.

  After the reboot, my PC went crazy and started broadcasting the message "TosBtMng has stopped working" and it restarted every time that I ask him to close.

  Installation of the new version of BT Stack (6.40) does not resolve this error.

  Help, please

  I also use Toshiba Satellite, I use this [suite Nokia pc | http://www.softsea.com/review/Nokia-PC-Suite.html] version

• Satellite Pro A300 - 2C5 has stopped working

  Hello

  I have a problem with my Toshiba Pro A300 - 2C5.
  It stopped working today.

  I have paid a top tea but removed is as fast as possible but a little water got inside my laptop.
  He worked for a while, I turned off and it works again an hour later, but unfortunately it has stopped working.

  When I try to turn it on, the syptoms are as follows:
  -the only light that shines is a power indicator light
  -l' screen does not work at all (it stays black and went offshore)
  -fan works
  -It seems hard disk does not work if Windows does not start
  -the keyboard does not work, when I hit tke keys nothing happenes, I tested the Caps Lock key, but not flashing
  -computer does not read my camera memory card

  What shoul I do to get it working again? :(
  Any help appreciated.

  K.

  Hello

  The anomaly can be related to different laptop parts in the worst case the liquid spill damage the motherboard and you will need to replace the part.
  In the best cases, it could be a RAM error as it happens to one of my friends.
  He spilled coke on the keyboard and after awhile the laptop could not turn on.
  We checked memory sharp and replaced both modules with new RAM modules and this fixed the problem

  You can try this also maybe it helps if all other parts should be checked by a technician of the ASP.

• Satellite L500 - DMIcheck application has stopped working

  Some of my drivers won't install givin message "DMIcheck application has stopped working" or similar for pInfo application...

  Same installation of 64 bit Windows 7 on another laptop didn't have problems like that.

  How to solve this?

  model laptop is L500 (short model No. PLJSHE)

  Hey,.

  To me that sounds like that the DMI information is missing, and if you get this error message...
  You use the Toshiba drivers directly?

  Usually the DMI information is missing, if the motherboard was exchanged and technicians forgot to re - write this information.
  In this case contact the guy again and they will do that for you! :)

• Satellite A305-S6825: WLan has stopped working

  I'm in the United States. (I posted this message earlier)

  #1-I just bought Toshiba notebook a month or two ago with Vista Premium SP1.
  A day ago when I turned on the laptop, I got a notice to the effect:

  Windows Wireless Lan 802.11 Extensibility infrastructure has stopped working.

  -> Are looking for a solution later (recommended) the next time that you start the system
  -> Closed

  Those who were only two choices. I think I clicked on the first "search for a solution later.
  When I turned on laptop today, I got the same message.

  Anyone know what could be wrong with this new laptop?
  I use the wireless to enter IE7 and type your message.

  My husband and I are elderly and not too familiar with computers or computer language so if anyone has an answer, please make it simple enough for us to understand.

  We hope that this new laptop is not already broken.
  We cannot afford to buy another computer or have it repaired.

  #2-we tried to send questions by e-mail to MS, but they asked the PID. We looked in Control Panel and system (I think) and typed in the PID of there (OEM number), but it would not recognize MS.

  Can someone please help?
  Thank you very much.
  Alice

  PS: We have the DSL cable attached to our desktop (modem/router) and use this Toshiba laptop with modem/router of this office to get online (don't know if that is the correct terminology that someone else connected DSL, etc.).

  Hello Bob

  I agree with Kody and I think also there is a software problem or the WIFI network is not properly enabled. I use the European model of laptop, but I don't think that there is some difference of laptop models to the United States.

  If you want to use the WLAN, it must be enabled correctly. At first make sure that the WLAN switch is placed in position ON. The WLAN led should be on. After doing this using FN + F8 key combination to activate the wireless network card. When you press the FN key and keep down. Maps flash in high must be indicated. Always keep the button FN, but press F8 and select Wi - Fi ON.

  So now the wireless network card must be activated, and you should also be able to connect to your WLAN.
  If the problem persists, you can try to roll back the OS to an earlier time (when the network WIFI works well). To do this, you must start System Restore tool. Choose different restore point and to the next day when you think about the WIFI worked well.

  Sorry, but for now I have a better idea because I don't want to confuse you more than necessary.

  Have a good day and I hope that WIFI works well again.

• Satellite C series - Touchpad has stopped working Windows 8 running

  Hello

  I put t know if anyone can help.

  My touchpad has stopped working.
  At first, it only works on the login page. Now it s not there at all.

  I've only had my Toshiba C for a few days and it s the first time I used Windows 8.
  I tried F5, and I tried to go on the BIOS with F2 when booting, but used to come.

  Help please

  Hello

  Please check this Toshiba document:

  + How to change the settings of the Synaptics touchpad in Windows 8? +
  http://APS2.toshiba-tro.de/KB0/HTD3101Z30000R01.htm

  Don't forget that the necessary parameters of the touchpad are enabled!

• Satellite A300 - DVD player has stopped working

  Hello

  The DVD in my A300 drive has stopped working. I don't find the driver in the control panel. The drive does not appear in my computer...

  Does anyone have an indices which me 100km of a service centre!

  Michael

  Hello

  If you didn t do a backup before deleting upper and lower filters that you can t restore it. This could be a bit difficult so, normally, you should always make a backup before you change or delete something in the Windows registry.

  As Akuma writes, you can try the system restore. Maybe it will work

• ThinkPad onelink pro dock carbon lenovo x 1 Ethernet port has stopped working

  Hello guys,.

  So after a few windows security updates my docking station ethernet port stopped working, it does not detect a physical cable connected. I've upgraded to the latest firmware for the dock but no luck, stops on the port to save energy also. If I connect the cable directly to my X 1 using the adapter of the eth-miniDP I get connectivity very well using the same cable and B end port.

  Update security for Windows 7 for x 64-based systems (KB3046269)

  Update security for Windows 7 for x 64-based systems (KB3042553)

  Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x 64-based

  Update security for Windows 7 for x 64-based systems (KB3045685)

  Update of security for Microsoft .NET Framework 4.5, 4.5.1 and 4.5.2 on Windows 7, Vista, Server 2008, Server 2008 R2 x 64 (KB3037581)

  Kind regards

  Andy

  In response to the client noted that when X 1 carbon ThinkPads (Type: 20FB and 20FB) running Windows 7 are moored via a Dock among +, ethernet does not work, Lenovo has presented a solution via the updated USB 3.0 driver.

  Version 4.0.6.60

  (Fix) Fixed a problem where the device USB-Ethernet among + Dock was unstable when you fix the dock.

  The latest driver for USB 3.0 can be downloaded here: http://support.lenovo.com/us/en/downloads/ds111779

  Thank you

• Satellite 1900-303 Touchpad: has stopped working

  The touchpad on my Satellite 1900-303 has suddenly stopped working for no apparent reason. The touchpad icon has disappeared from the office toolbar & I do not see the touchpad listed in Device Manager. However, the ALPS touchpad driver is listed in the installed programs.

  The laptop runs on XP Pro SP2. Can anyone help with this please?

  Can you imagine that the TouchPad is defective and this may be the reason why it doesn't work?