Satellite L300D cannot burn DVDs

Similar Questions

• Satellite L20: Cannot burn DVDs - power calibration error

  Hello

  I have problems when you try to burn the DVD on my Toshiba Satellite L20. Nero indicates a "power calibration error". Lens and drive have been cleaned up, but it did not help. Supprisingly, DVR +/-RW and CD are treated correctly. DVD player of any sort is also OK. Only burning DVDs (+/-), regardless of their manufacturer, fails.

  The next step, I wanted to put a fresh firmware in the drive which is Mat * a UJ - 841 S. I found the firmware on another site of PC companies. But the installer stops with the message that it does not apply to my reader however it was designed exactly for this kind of car.

  On the website of Panasonic, manufacturer of the drive, there is the information that support for this model is provided by the hardware vendor - in this case, it is Toshiba. But there is no firmware for this drive on Toshiba support pages.

  Can anyone help me, please.
  Thanks in advance.

  Piotr

  Hi Piotr

  First of all, note that after the installation of non-Toshiba firmware yourself, will lose it warranty for the reader. In any case, on a forum I found an interesting solution. You can try:

  1) click Start
  (2) select control panel
  3) click on Administrative Tools
  4) click on services
  (5) go your way down to SERVICE of the COM of ENGRAVING of IMAPI CD
  (6) right-click (on IMAPI), and then select Properties
  (7) in the middle of the window, it will say start type. Click the arrow on the right and select disabled.
  8) click APPLY

  I also noticed that Nero starts much more quickly than before. I recommend you test different blank media.

• Re: Satellite A200 - cannot burn DVDs

  I had a Toshiba Satellite A200 for several years and have never had a DVD burning problem before.

  About a week ago when I tried to burn a DVD with Nero, he went through the motions and was told everything had been done successfully, but when I went to read the DVD, the computer told me that it was a blank disc.
  I tried to use different programs to burn on DVD, with the same result every time. My DVD drive is a TSST corp CDDVDW TS - L632H ATA Device. He can still play the DVD already made and play, then I start to think that the party "burnery" (I'm fine with the techno jargon) has made his dash.

  Does this mean I need to replace the drive?
  All the answers you guys could give would be greatly appreciated, it has become a bit frustrating.
  See you soon

  First try to remove upper and lower filters: http://support.microsoft.com/default.aspx?id=314060

  Second, make sure that there is no dust on the lens, use a Microfiber cloth to gently wipe the optical lens.

  Third, look for a firmware updated the L632H drivers Toshiba Web site.

• My Satellite A100 cannot burn DVDs

  I have a rug * a DVD-RAM UJ - 841S who is really fighting with burning discs. Although the system recognizes the drive Ok when I go in WinDVD creator or Roxio there is no disk selected and no to select. It seems that none of my burning software does not recognize the drive. Any ideas?

  Hello

  What to say! Pre-installed images are tested and if your device has a factory settings, it should work fine. If I remember correctly, the set comes with the NOW called RECORDING of SONIC burning software. I hope you have tested before use of Roxio.

  Try to remove all the burning software, install Nero and test it properly. Sonic and Roxio maybe some conflicts and engraving option is not available.

• Satellite A300 - cannot burn DVDs dual layer

  Hi, I bought my laptop 10 months ago.

  Since then I ve been burning a disc or two every now and then, no intense use of the driver.

  Last week I tried to burn a DVD double layer, my driver seems not to be able to burn a. I used BurnXP free burning software that supports double layer and when he finished the first layer of the program collapsed in response, I have tried 2-3 disk, none worked.
  Then I tried the latest version of Nero, everything seemed smooth (it burned down two layers) up until the finished burning process and then I got an error message that the procedure has failed.

  I have tried different brands of disc 'TDK' 'Philips' "In extenso" or something. None worked.
  I tried a Philips disc on my desktop drive and it it burned very well.
  -Should I head to Toshiba service?
  -Are there a driver/firmware to fix my problem?

  PS: I tried to update firmware but can't find a firmware for my drive.
  I have the ' matsita DVD-RAM uj-850 s and I used the right type of DVD discs--
  Type in advance.

  > So I tried the latest version of Nero, everything seemed smooth (it burned down two layers) up until the finished burning process and then I got an error message that the procedure has failed.
  You have received this message, but have you checked the DVD DL after that?
  Perhaps the data has been burned correctly?

  I got a lot of time, the message that the burning procedure was not successful, but I then tested the disc and it was legible.

  AFAIK that should the user manual contains also some info on drive tested and compatible.
  Maybe you should use the DVD DL recommended in this user's manual.

  But of course this could be also a material IRREGULAR deadlines.
  In this case, you must request the ASP for the test and check!

• Cannot burn DVDs on my Satellite C660

  I just bought a new complete Satellite C660 and I cannot burn DVDs.

  Tried to burn with the recovery media creator, Nero, IMGBurn and all fails at around 75%.
  When I tried to burn the recovery CD as I was asked that they have failed because of a problem STARTING...

  You can create DVDs from recovery use preinstalled Toshiba recovery media creator. Please test using DVD-R media.

  Have you tried using different media of high quality as TDK or Verbatim?

  Sorry, but this startup message said nothing to me. I've never seen something like this, even if I created several on several laptops Toshiba recovery disks.

• Satellite A80-129: Mat * a DVD - RAM UJ-830 s cannot burn DVDs

  MODEL: SA80-129
  DVD RAM TYPE MAST * A DVD-RAM UJ-830 S
  SYSTEM: WINXP
  SOFTWARE: NERO

  (1) DVDRAM CAN READ CD AND DVD EASILY, IT Burns CD WELL, BUT cannot burn DVDs, IT SHOWS: G:\ IS NOT ACCESSIBLE INCORRECT FUNCTION, UNTIL IT WORKS WELL. the blank dvd is not a problem, before I used even type a blank dvd to burn.
  (2) even allow the recoding in the properties, the properties shows the Virgin dvd 0bytes.

  all PROMTLY ANSWER would BE MUCH APPRECIATED.

  It doesn't sound good.
  I had a similar problem of combustion and the end of the story, I replaced the drive ;(
  However, try to remove the drive from Device Manager, and then again to restart the operating system should recognize the device again.
  Then you could check if it able to burn the DVD s s.
  I think you should also try burning different DVD media.

  I have visited many work sites and the reader, and especially the calibration lens malfunction could be responsible for burning problems.
  This could be a worst case and in this case, the replacement is necessary.

• Program for creating Windows DVD cannot burn DVDs

  Program for creating Windows DVD cannot burn DVD due to can not find the DVD burner, free DVD burner disc see on the upper right. But my DVD drive with well with another burning program.

  Hello

  (1) have you made changes before the start of this issue?

  (2) you have the external devices connected to the computer?

  (3) what is the exact full error message?

  (4) is specific to the program the issue?

  Method 1: Clean boot

  How to set up Windows 7 to start in a "clean boot" State

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: Resolution of the problems with creating a DVD-video using Windows DVD creation

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-creating-a-DVD-video-using-Windows-DVD-Maker

  For reference:

  DVD-video burning: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/DVD-Video-burning-frequently-asked-questions

  I hope this helps.

• Cannot burn DVD-R with my Satellite P100-342

  I bought a Satellite P100-342 two years ago. Some time after I tried to burn DVD + R and it was impossible, so I sent it to Toshiba. A few weeks later, when they returned to my laptop I saw that I can burn DVD + R, but it was not possible to burn a DVD-R.

  I tried with many manufacturers of DVD - R, but no one works.

  I checked my DVD multi recorder (HL-DT-ST-DVD RAM GMA-408N) with Nero Info Tools and it checks ON items: DVD + R and DVD-R. It shows that system ASPI are not installed and I don't know if that's the problem.

  My OS is Windows MCE.

  Will you help me, please?

  Hello!

  This DVD did you tested on your laptop?

  I use discs Verbatim always and never had any problems with it. You may also try verbatim and post workout.

  Good bye

• Satellite M45-S169 - Sonic v.7.31 cannot burn DVDs more

  I am using a v.7.31 Sonic Record now prepackaged on my Satellite M45-S169 for three years now.
  I was able to copy DVDs using this software.
  Until recently, it burns more.

  What's most frustrating is that space of memory on a blank dvd just exhausted once I try to burn dvd on cd files.

  Help! Help! Help!

  Hello

  Have you tried to delete upper and lower filters in the registry of the Windows operating system?
  Isn't it? Try this:
  Completely remove the Upperfilters and Lowerfilters from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Also I would not recommend trying the other and different discs (CD and DVD) from different manufacturers.
  But of course it could also be a hardware problem. I mean the discs of the laser lens has stopped working properly due to mechanical stress.

• Satellite M40: Power calibration error - drive cannot burn DVD - RW more

  My drive is a carpet * an oem UJ - 831S. After a screw-up partitioning job, I had to format my HD and reinstall Windows XP... and then I can not burn DVD - RW more.

  Tried many programs such as Nero and a fireman, gives an error of calibration of power from the beginning.
  Burning CD - r and CD - RW no problem however, and I can read CDs and DVDs of movies very well.

  Google and searched for a month without success, tried to blow the laser lens, but there is no dust, I tried different media, etc. I know the best answer is that the drive is done, BUT I refuse to acknowledge it because it is too big of a coincedence to stop working right after that I reinstalled XP.

  An interesting note however, my laptop has not been provided with a CD of Toshiba, so I had to reinstall manually more drivers by downloading the Toshiba site, so I have a funny feeling, this could be a thing of the software/firmware, or even a framework.

  I installed the new firmware 1.02 for the reader as well. I don't remember what the firmware was before resettlement, IE the laptop computer settings to factory default, I'd like to downgrade to 1.00 if possible.

  Experts have ideas? And is there a way I can reset the firmware?

  Maybe I could remove the drive from the system-> devices and let XP Reinstall for me?

  Hello

  > I don't know the best answer is that the drive is done, BUT I refuse to acknowledge it because it is too big of a coincidence to stop working right after that I reinstalled XP.

  Of course, it s simply to say the drive is dead because everything looks like a hardware malfunction. Most often the power calibration error appears because of the drive lens can't calibrate in the right position and thus cannot read some CD or DVD s s or it of not possible to write about them.

  But maybe you are a lucky man and might try this procedure:
  -Try to remove the drive physically from the Bay for laptop
  -Restart the unit without the drive
  -In this case the operating system should start from the HARD drive
  -Close the notebook then reinsert the drive unit in the Bay of s for laptop
  During initialization, the laptop should recognize the drive and must pick up the firmware

  Then you can check if you can burn the DVD again, otherwise you will need a new drive

• Satellite Pro L650 - ODD cannot burn DVDs

  I can't burn DVDs. That is to say to ensure that I have the latest firmware I checked and do but still does not work please help

  Can you please tell us which laptop model you have and what operating system are you using?
  Your optical disc drive can read the DVD?
  What burning software do you use?

• Re: Satellite L300D-11V-CD/DVD drive not recognized after upgrade to Windows 7

  Hi, I have a Satellite L300D-11V model pslc0e and have upgraded to 32 bit Windows7 ultimate. I downloaded all the necessary drivers on the toshiba site, but he acknowledges that he has a cd/dvd drive!

  Can I put any disk in, but it will not load up or even acknowledge that the car exists!

  Help, please!

  Thank you

  James

  Please, read here:

  http://APS2.toshiba-tro.de/KB0/TSB7801XL0000R01.htm

  This is for Vista but works for win 7 too. I checked it myself before.

• Satellite L300D - cannot connect wireless Internet

  I just bought a Toshiba Satellite L300D-202 and can, t connect to wireless internet. When I try to connect it only gives me not a wireless option, I only get cable or dial options. We have not seen all the wireless devices.

  When we passed by Toshiba assist/connect/conective doctor and pressed the radar message was peripheral wireless network is disabled please turn on the device.
  The wireless switch is active, the light is orange.
  Our other laptop is fine.

  Can you help me?

  Thanks for this info!

• Qosmio G10-133: cannot burn DVDs more

  Since the first day I was never able to record on a DVD. I've tried many discs. Different software. I get that day, but when the deer of burning starts, he discusses the creation of a newspaper report. Any ideas.

  Do I need a new rom?

  Hello

  I guess it was possible to burn DVDs to the start time.
  Well, it's not easy to say why it doesn t burn DVD media.
  Sometimes, perhaps because the wrong lens calibration.
  But in this case, you should replace the disk.

  Also a non compatible DVD media could be responsible for these issues.
  Please see the manual for the DVD compatible and tested.

  You can also try to remove the drive from Device Manager. After restarting again the operating system should recognize the drive again.
  Then check if it of possible to burn DVDs