Screen remains black after start-up M30X 124

Similar Questions

• I have an old iMac (about 10 years) and after a power cut the screen remains black after start-up

  IMac was on but in the sleep when had power cut. After feeding back immediately tried to start over, but I just black screen that could hear the startup chime, and hear the work of the machine. In collaboration with el captain. I have mouse and wireless keyboard. Any ideas?

  Reset the management system (SCM) controller on your Mac - Apple Support

• G62 screen remains black after the windows logo

  Hello

  I have a HP G62-b05SD. I noticed that many people have the problem of simmular.

  I know what makes, but don't know how to fix it.

  So here it is.

  Sometimes when I boot / reboot system screen turns black after the windows logo, but if I wait a while, I do not hear the star tune up windows, but the screen remains black.

  I noticed that this happens when I shut down or restart the system with a usb port (be it a mouse or a stick is not serious)

  If I all out en usb port restart or turn on the machine for the first time this day here, everything starts well.

  So there must be some driver problems I think with usb ports and the screen or something.

  Help, please!

  HP G62-b05SD

  Windows 7 64-bit

  Intel i3

  ATI mobility radeon graphics card

  Ow and when I get the black screen, the hard reset does not always work.

  I also did a startup repair and it showed:

  "If you have recently attached a device to this computer as a camera or portable music player, remove it and restart your computer. If you continue to see this message bla... bla... bla... "

  I hope you can help.

  Hi Frosty1984,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP G62 - b05SD Notebook and having problems with the starter. Here is a link to BIOS update.

  What is the USB device that is at the origin of the questions?

  Thank you.

• Satellite A100-495 - screen remains black after switching to food

  After feeding, the screen remains black, the computer no longer works.

  What can I do, why?

  > After the transition to power, the screen remains black, the computer no longer works

  It works fine on battery?

• Satellite L670 - screen remains black after sleep mode

  I recently bought a L670. When I close the laptop, it goes into sleep mode. No problem with that. But when I opened the laptop again the screen remains black.
  I see on the drive activity light that the laptop come out of sleep mode correctly, but the screen remains black.

  I don't have this problem when the sleep mode is only a few minutes. Then the screen comes up correctly.
  But for example after an hour of sleep mode... no screen.

  I'm doing something wrong?

  Thanks in advance for your feedback.

  Hello

  I recommend the update to the BIOS and the display driver.
  It helped to solve a similar problem on my old laptop.
  Maybe it helps in your case.

  Good luck

• Satellite 3000 - X 4: screen goes black after start

  Hello

  I have a laptop of s3000 - x 4 satellite.

  swiched top upward start then the screen goes black, I can just do the display to see loading, windows
  This happens even if I can get it to boot in safe mode, or when I enter setup.
  If I'm lucky, I have a minute of commissioning until the display changes. and as soon as I restart, I'm square.

  can anyone help? If it is a component, it is easy to find and replace?
  see you soon

  Colin

  Hello

  Have you tried to connect the external display?
  If this is not the case, try it. Also check out the switching between display devices with the FN + F5 key combination
  If this does not help, I would pick up the laptop with the Toshiba Recovery CD supplied. Also try to improve the shape of the Tosh site graphics driver.

  But if it won't work and you can't see anything on the screen so I guess there must be something wrong with the hardware. In this case only the ASP in your country is able to help you.

• My screen remains black after I wake my computer confirmation form.

  When I wake my computer, the status light on the power button stops flashing and lights up, indicating that my computer is no longer in standby mode. The screen remains dark, however, and I don't know if the sound works, but all I can do is do a hard restart. It is very annoying and I'm afraid it will damage my computer. Help, please.

  I read something on a fix for a similar problem on Microsoft Community, but I don't know if that is the solution (I remember that patches were potentially dangerous) and it is still a time to me. Another solution, I found was to update my driver, but depending on the devices I already have the latest version of the driver for my screen.
  If you could help me out or give me a link to the fix, I would appreciate it a lot.
  I have a G-62 HP laptop running Windows 7 64 bit, I installed on an ISO downloaded with a product key, I bought. My graphics card is AMD Radeon 4200.

  Video card problems are the most common cause of this problem.

  Try the following troubleshooting procedures in the order. If the steps described in the first procedure does not resolve the problem, continue to the next procedure.

  Reinstall your video driver

  1.
  Right-click the taskbar, and then click Start Task Manager.

  2.
  Click on the processes tab, click explorer.exe, and then click on end process.

  3.
  Click file and then click New task (run).

  4.
  In the text box open, type explorer.exe, and then click OK.

  5.
  Click the Start button, type in the box Device Manager search and then, in the search results, click on Device Manager.

  6.
  Double-click Display adapters, right click the display device, click Update driver software, and then follow the steps in the wizard that appears.

• a sound signal and the screen goes black after start

  Hi, I have a problem with my HP G62 a38se laptop pc.when I start my pc after startup pc saying not to answer with 3 beep sound(beep...beep...beep).after it displays a black screen and goes restart... plsss help me for this

  You are able to access UEFI to perform material tests?

  Perform the start-up and testing of the long system. Please post your results here.

  Kind regards

  ERICO

• Computer crash (screen goes black after start)

  I can start my computer very well, he goes through the bios and connect simply awesome. But when I connect to my computer (click on my icon, enter the password), the office and the screen goes completely black apart from my mouse is showing and answer. My keyboard works, but just does not meet all the shortcuts and there is a way I have to go on the Control Panel, but I can't open applications or files of it.

  I can alsostart in security mode and works perfectly; Apart from theres no internet.

  I checked inside my computer and nothing burned or destroyed.

  Hello

  If you are normally able to logon in safe mode, this means there is a demand of load in normal mode, interfering with the Explorer shell. Safe mode, click Start and run regedit. Expand the branches to reach this key:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  Cliquer click the button, then find the userinit string in the right pane. Double click it, replace the contents with:

  C:\Windows\system32\userinit.exe,

  be sure to include the comma at the end click ok, close the registry editor and restart the system normally.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Screen goes black after start

  2 #1 monitor displays a normal "office" and then turns black 5 to 20 seconds after turning upward.  Sometimes displays 'no signal' on the way to black.  Power Off then on restores it for another 5 to 20 seconds.  Discount to zero has the same effect

  This config double montor was working before?

  In the resolution of the screen, the monitors can be detected?

  Swap monitor connections on the PC, the same monitor fails then?

  Check that all are watching them (removing and reinstalling) cable connections

  And or check the monitor on another PC

• Satellite P100: screen remains black after the awakening of the mode standby

  Hello!!
  Can someone help me with this problem?
  I update my bios [V3.30] 12.22.2006 and now I have a problem.

  When I put my laptop P100 in stand by and I return my screen no longer works! I push every button on my keyboard, I move my mouse but nothing.
  Only one solution to come back is to close my laptop and reopen after that.

  What to do? Please help me if you have any ideea!
  Best regards to all!

  Hello

  I hope that you used the good BIOS.

  Have you tried to update the graphics driver? Not? Then do it!

• Satellite M100 - screen remains black after sleep/wake

  I just installed Windows Vista Ultimate on my Satellite M100 series.

  Everything works fine, but when the pc is forced into sleep/standby or it automatically goes into sleep/standby mode depending on the time of inactivity in the power settings could not be restored sleep/wake without turn off and restart.

  The blue button is orange and blinking indicating sleep/standby mode. When you press it again, it turns blue and the fan turns on. But there is no display and no response. The only option is to go to market.

  Help, please

  Hello

  What BIOS updated to the latest version?

• When I start my Equium P200D screen remains black

  Hello

  I have a portable Satellite P200D-139 (WinVista). I left on during a few hours after work a day to to this subject when I came back the screen was black, but there is no way get back on. I have turned it off manually (I know we're not really supposed to do, but I had no choice) and tried to turn it back on to the it, but there is nothing happening.

  I can hear it start about 2-5 seconds, then it's as if he won. I can still hear a slight noise hum (fan), but it is not from, and the screen remains black. Nothing lights up.
  I tried to cool, I tried to remove the battery, nothing works.
  I tried using F8 to repair, but is not answer either.
  I don't want to reformat it completely right now that I have docs and photos which I did not have time to put on the disk.

  Anyone would be able to help me with this? That's my working tool, so I'm kinda stuck with this problem.
  A big thank you to all those who can help.

  Kind regards
  Stéphane

  Hi Stephanew,
  as I recall it has an ati graphics card...

  but try this to get your machine to work:

  -pull out the hard drive to protect your data (Let's hope that there is no damage yet...)
  -take out the battery and try to start only with the power adapter > shoukld you see the toshiba on-screen logo > failure other components can be 'guilty '...

  -attach an external monitor to your computer and check if there is a visible image > no image at all?
  -check the memory, for this purpose, remove the memory and test if the satellite "buddies" > heard some of this? Yes?

  iasume the grafics card disappeared... see your certified partner...
  Let us know if this helped you.

• When I start my Satellite A300 the screen remains black

  When I turn on my Satellite A300, the screen remains black and doesn't change at all... Any help please?

  What is password problem in your other thread? Already solved or what?
  If the problem persists, I don't see any sense to start this thread because people don't understand what the problem is.

  Please do not mix two questions and explain exactly what you see on the screen after turning on your laptop.

• Satellite A200 screen remains black when you try to start

  Hi all

  My Toshiba Satellite A200 laptop computer no longer works, then everything started when I was playing a game, all of a sudden the screen turned blue with a tiny text written on it. I had to hold the power button for a few seconds to close, because nothing not happening on the computer. Then, I pressed the power button to open it. Everything was fine, until the Welcome screen. In this part, he wrote 'Welcome' but Vista left loading circle of it was not turning.

  After a few seconds, I decided to shut down the computer once again, so I hold the power button for the computer firm. Here's the problem: I tried to re-open it, but the screen remained black. Nothing was happening. The power light is blue, but not all computer activity. So I left it like that a few minutes then it closed and tried again, but it's the same thing. I tried to take it apart and noticed the card two memory was not entirely in its niche. I fixed it, but it does not solve the problem.

  I also tried to plug another screen on it, but this one was also black. So I handed the screen on his computer and tried to boot my laptop and it worked. He was the starter, but the first problem came, the Welcome screen was frooze it. So yes I close it up and then it's the same thing, the screen remained black.

  I don't think the problem is the screen, because as I said some time it goes to the Welcome screen. Also, I hear no welcome sound when the screen remains black as if the computer would simply not starts. And as I said earlier, I see no activity of the computer on the little light in front of the computer. And to the left of it, I see clearly that the computer is ON, because the power light is blue.

  That is my problem, the next time that the computer is able to start I'll try to boot mode SAFE, but until then, I don't know what to do. Please, help me.

  Thanks in advance,
  MrRoy

  EDIT:
  After the computer is turned off for about 30 minutes, I started and booted in safe mode. At this stage, I have locked my computer with the close button instead on the power button. Then I opened my computer and he started and the problem was solved. Now my laptop is open and working.

  So, if this happens to you:
  1. turn off your computer.
  2. wait about 30 minutes.
  3. start in safe mode
  4. close using istead of now off button power button closure.

  It should work.

  Finally, it does not work. I don't know why, but my computer did start after 30 minutes, but now it no longer works. Only, it will not start as I said later, with a black screen.

  The computer worked for about half an hour. I mean, I managed to start but after running a program, it just froze and I had to hold the power button to restart. I made about 3 or 4 times, and then he was simply the black screen again. I think the problem is my processor, maybe that it is damaged or something, would it possible?

  Because I see that the processor does not work when I try start it.

  So let's say that this is the case, would it be the symptoms of my computer?
  And if it's the processor, the only way to resolve this is to send it to a repairman or something, because I don't feel like it, I'd rather do it myself.

  But now, my computer is simply not starting, as I said in my previous post.

  Thanks in advance,
  MrRoy

  -----

  Note: The Edit button was not there so I had to double post :/