Several monitors and Ethernet cable

Similar Questions

• Problems connecting an Officejet 7310, wireless and ethernet cable

  My printer (Officejet 7310) is connected to two PCs with an ethernet cable and the router. Now I want to install a laptop as well.

  I know that the lap top is communicating with the wireless router, but I can't get the laptop to recognize that there is a printer is installed.

  I tried to connect the printer directly (via Ethernet cable) to the laptop and it works fine. I downloaded the latest version of the software for the 7310 and used two options (without wire and cable).

  Any help would be most appreciated.

  Cutting the anti-virus made no difference.

  I HEALED NOW THE PROBLEM!

  Installed a new router 2wire.

  Thanks a lot for your help.

• Re: NB200 - automatic plug-and-play for Ethernet cable

  Do you know why I don't have automatic plug-and-play, when I connect to internet ethernet cable on my NB200?

  Hey mate,

  Automatic configuration tell you exactly?

  Normally, nothing is plug-and-play. If you want an Internet connection via Ethernet cable, you must configure this port. This means you need to set a static IP or DHCP.

• I am trying to connect a Macbook Pro with Retina display for a new monitor Dell Ultrasharp 3014. I tried to connect via HDMI and DVI cable supplied with the monitor but the monitor says "no cable dvi - d".

  How to connect a Macbook Pro with the (just bought) Retina display for a Dell Ultrasharp U3014's new? I tried to connect with HDMI and DVI cable supplied with the monitor but the monitor says "no dvi - d" cable. I never tried to do that before so I'm lost.

  Use a mini-displayport cable. Connect to one of the ports Thunderbolt the MacBook Pro to ultra-compact monitor entry.

• I just bought an Airport Extreme and try to put in place.  I have Fios cable with a router.  I can not get anything except a blinking orange light.  After reading the instructions, it seems that the problem with the ethernet cable but I

  Must not exceed the flashing orange light.  have tried three ethernet cables to the Fios router.  All thoughts

  What extreme version do you have?

  Test the cables connecting the airport to your Mac with them and see if the ethernet works on Mac. Green connectivity light should go... If it fails, then the AE died.

  Please do a factory reset, then try again.

  Sometimes Mac airport utility works well... If you have the preference or iphone ipad, download and use iOS version airport utility and try it for configuration... It is much less awkward.

• Can I connect a VGA cable simultaneously with a DVI cable to a monitor and use the source switch?

  I found a similar, but not exact question and I was wondering if I could use the VGA cable AND cable DVI simultaneously on a HP 2159 m monitor and switch back and forth from analog and digital using the source switch on the screen? I noticed that some casual games such as found at BigFish and other gaming sites works best on VGA on DVI but I like to watch movies and other DVI instead of VGA?

  I did two HP 2159 m monitor but it could in fact be wise space more convenient to just use the right now and switch from the analog to the digital format.

  Thanks for any response.

  Hello

  You will need to edit the video in the monitor source selection when you want to switch.  Don't put it on AUTO.

  For a test, connect two monitors and then configure your PC for two monitors. Then, remove the monitor as the secondary (VGA) and now connect the cable to the main monitor VGA port.  Now try the video source selection in the menu of the monitor.  I never tried it on my 2159 m but it can work.

  Some monitors do not react to two active flows.

• How to connect a portable laptop Windows 8 with Windows 7 computer via Ethernet cable and transfer the data directly?

  I have a laptop Windows 8 . I want to connect to a new round of windows 7 and transfer the data at least 8 MB/s.

  Please send me the procedure to follow. I don't want to share Internet, but want to transfer data.

  You can do this, but you need a special type of Ethernet cable called a crossover cable.  This means the son in the swap position cables so that "send" and "receive" the computer two plugs can communicate.

  Learn more here: http://windows.microsoft.com/en-us/windows/connect-two-computers-crossover-cable#1TC=windows-7

• I can stream movies on my PC using the desktop PC monitor. But when I unplug the monitor and use a PC to TV HDMI cable I get the video but the audio now

  . Video streaming

  I can stream movies on my PC using the desktop PC monitor. But when I unplug the monitor and use a PC to TV HDMI cable I get the video but the audio now... Suggestions?

  Thanks for the file INF. I ck'ed for driver updates and I have the latest drivers installed.  I got the sound working on the TV by hanging the audio output of the PC to the entrance of the TV with the HDMI cable in place for video. It's the simplest solution to this problem, so I took it.

  By the way, I have a Dell 620 with windows 7.

• my laptop has completed the automatic update of vista and after that I can't access wireless router with an ethernet cable only

  My sony vaio laptop running windows vista has completed an automatic update and after that, I can't connect to my wireless network, I can access the internet with an ethernet cable.

  It worked perfectly fine before the update, I know that there is a problem with what I had the same problem in the past. The way it's been solved previously was to restore the laptop to an earlier point before the end of the update. Unfortunately I can't do that and the laptop has been completed, wiped and there is no backup where I can go to restore.

  I know I can remove some updates but don't know what 1, me it is another way to solve the problem.

  Your help would be much appreciated.

  Thank you

  Hi Nadzarif,

  You can try the following steps and check if it helps:

  Method 1:

  Because the wireless stopped working after windows update, you can check the Sony support link and try to install the latest version of the drivers for the wireless card and check if it helps:

  Sony support

  For more information, see the article:

  Update drivers: recommended links

  Method 2:

  Updated version has a problem in the history of the update.

  Step 1:

  You can check in the history of the update for the updates that are installed recently or before the show.

  a. open Windows Update by clicking the Start button. In the search box, type Update, and then in the list of results, click Windows Update.

  (b) in the left pane, click view update history.

  c. to display more information about an update, double-click it.

  See the Windows updates are installed

  Step 2:

  Uninstall recently installed updates and install the updates one at a time to understand what update is the cause of the problem.

  For more information, see the articles:

  Remove an update

  Install Windows updates

• I can't connect to internet unless I'm using an ethernet cable. I am on a computer laptop lenovo and cannot connect to my home internet group. When I troubleshoot, my device is not found. What should I do?

  My computer now has internet but my laptop cannot get any internet without ethernet cable. When I troubleshoot, my device is also unrecognisable.

  Hello

  1. who troubleshoot steps did you try?

  2 did you change on your computer?

  Method 1:

  I suggest you to see link and check.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  I also suggest you to see link and check.

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Troubleshoot low wireless signal quality

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-low-wireless-signal-quality-problems

• How to enter a wireless signal and convert Ethernet cable?

  I'm totally bafled by the nomenclature of wireless gadgets and would appreciate help. I already have a wireless router that allows my laptop work anywhere in my house. My need is to recover the wireless signal and somehow get this signal into an Ethernet cable.

  The reason is that my DVR (Replay TV) connects to Internet via Ethernet (not USB) cable and I want to move to a place where it would be impractical to try the new wiring through the walls.

  Thank you!

  You need a "wireless ethernet bridge", like the WET54G, WET200 or WET610N.  Once you set up the device, just wire your DVR to it.

• computer goes to sleep as soon as the ethernet cable is plugged in and don't wake up

  When the ethernet cable is plugged into my pc, it immediately goes to sleep and don't wake up without a difficult start. As long as the cable is connected, the computer will not load windows, immediately go to sleep before my desktop appears. My laptop is connected wirelessly without any problems at all and when connected with a cable, no problem either. ISP says it's a pc no matter not a modem problem, there is a conflict, but they don't know where.

  I am running windows Vista Home Basic, a cisco modem, do not know what model.

  Any help would be appreciated.

  Hello

  1. don't you make changes to the computer until the problem occurred?

  I suggest you to check the parameters of the power management of the device on the network adapter.

  To correct the settings please follow these steps.

  (a) click Start, type device in the box start the search and then click on Device Manager in the programs list.

  (b) in the user account control dialog box, click continue.

  (c) in Device Manager, expand network adapters.

  (d) right click on the network driver and then click Properties.

  (e) click the power management tab.

  (f) click to uncheck the checkbox allow the computer to turn off this device to save power , and then click OK. If the option is checked, then uncheck the option and apply the settings.

  Once you have performed the steps, restart the computer so that the changes take effect, and then check the result.

  Hope this information is useful.

• network discovery, file sharing and public folder sharing won't turn on if the ethernet cable is removed and plugged

  Public folder of Windows Vista sharing problem.

  Whenever my pc is disconnected from the internet sharing files turns back on. Options: network discovery, file sharing and public folder sharing will turn on if the ethernet cable is removed and plugged. How can I prevent this from happening.

  Hello

  1. Since when are you facing this problem?

  2. don't you make recent changes?

  I suggest you try to perform the clean boot and check if it helps:

  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that restore you the computer mode normal startup such as suggested in step 7 of the above article.

  For more information, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/file-sharing-essentials

  It will be useful.

• MB Pro restarts randomly with the ethernet cable is plugged

  I recently bought a thunderbolt reduction - Ethernet [1] and it works very well. The problem is that when it is plugged in, my MacBook Pro (13', 2015, i5, 8 GB) gets very hot. This isn't a problem, but the next thing is really annoying.

  Whenever I'm not load, but the ethernet cable is connected, and MacBook goes into sleep mode, the system turns off instead. Thus, for example, when I don't have the power cable and if go for 5 minutes, the system automatically sets the mode 'sleep'. When I come back, it is turned off, and when I hit the power button, a black screen with the Apple logo and a text in several languages, saying that the system restarted because of a problem. After that, MacBook starts normally.

  The same phenomenon occurs:

  • When the power cable is not connected and I close the screen
  • When the power cable is not connected and I SLEEP manually the MacBook
  • When the screen is closed and I plug the power or the ethernet cable

  I use OS X 10.11.

  [1]: shot of lightning-Ethernet reduction ter http://www.apple.com/shop/product/MD463LL/A/thunderbolt-to-gigabit-ethernet-adap

  The SMC reset may help:

  https://support.Apple.com/en-us/HT201295

  Ciao.

• Can not connect Equium M70 to the Internet via an Ethernet cable

  I have recently install wide telewest broadband via the installation disc. I used the provided ethernet cable. During installation, I received an error message stating that it could not connect due to various problems.
  After a long discussion with the customer service and try several solutions over the phone we wouldn't always get connection using the ethernet cable.
  Telewest has also provided a USB cable so I was told to remove the ethernet connection and plug in the USB. The connection has been made instantly.

  Has been informed by the technical support of Telewest, that I had a problem ethernet on the laptop. This could be correct, or maybe it was an ethernet cable from the spleen.
  Any suggestions? My laptop is only four months.

  Hello

  It is not easy to believe that the network adapter does not work on your laptop. What is the status of LAN in Device Manager? When the cable is connected is the assets of orange or green led or not? Try also to start ConfigFree tool. Under the physician connectivity tab, you can see their actual situation and if there is a problem of communication it will be shown here.

  If there is any attempt of trying to test it on another network (perhaps in your company).
  You can also contact your dealer and allow it to check the device. It can be done in the store and may not take a lot of time.