Slower speeds when using the router from Linksys e2500

Similar Questions

• Why is my slower than wifi ethernet download speed when using the airport extreme?

  Hi all

  This is my first post here, so please bear with me. I currently own stunted 2011 Macbook Pro 13 inch and an extreme A1521 from the airport. My ISP has promised 50Mbps downloading and sending 10 Mbps. When I connect my MPro via ethernet/wi-fi to my modem I get as promised. When I connect my MPro via wi - fi to the extreme I get 48Mbps download download 9Mbps and it's ok. However, when I connect my MPro via ethernet to extreme I get 8-9Mbps download and 9Mbps. Anyone know how to fix this?

  If you check the 'fine print', your ISP has promised "up to" 50 Mbit/s and 'up to' 10Mbps.  The ISP might provide more than that during periods of slow activity, like the days of the week during the day, but much less during evenings when there are many more users on the Internet.

  When I connect my MPro via ethernet/wi-fi to my modem I get as promised

  I assume that you meant to check the Ethernet connection, you disable WiFi on Mac when you do this. And unplug the Ethernet cable when you check the speed of the WiFi, correct?

  If so, this tells you that the Ethernet port to both the modem and the Mac work properly, and WiFi work correctly as well.

  When I connect my MPro via wi - fi to the extreme I get 48Mbps download download 9Mbps and it's ok.

  If this tells you that the Ethernet connection between the modem and the AirPort Extreme works correctly, and wireless works fine on the AirPort Extreme.

  However, when I connect my MPro via ethernet to extreme I get 8-9Mbps download and 9Mbps.

  Well, you know that the Ethernet connection between the modem and AirPort Extreme works because you can register 48 Mbps Wireless.

  Thus, the possibilities are narrowed to two elements at this stage:

  (1) the Ethernet cable is defective or making intermittent contact. Try another Ethernet cable, to ensure.

  (2) If you have turned off AirPort Extreme and rebooted several times, and you know that the cable between the Mac and AirPort Extreme works properly, then you have reduced the question down to the Ethernet on the AirPort Extreme, which is probably defective switch.

  If you have not already done so, try other ports Ethernet on the AirPort Extreme.

  As a last resort, perform a reset material on AirPort Extreme and put up again. To perform the Hard Reset... power on AirPort Extreme for a few minutes, then hold it pushed in the reset button on the back of the unit (near the AC power plug) for 7-8 seconds and release. Allow a minute for the AirPort Extreme restart orange light flashing slow.

  I once went through two consecutive airport extremes with the same question about 8 months ago, so it can happen.

  If you're still having problems, then it is time to take the AirPort Extreme of Apple Store... If you have one near you... or contact the Apple Support directly by clicking on 'Contact the Support' in the upper right area of this web page.

  Good luck!

• Ask the slow operation when using the subwoofer inside when

  Hi all
  
  I am creating a query according to the following conditions:
  
  Select count (*) in A Alpha, Beta B
  where
  (case
  When
  A.col1 = 'Pete' and substr (A.col2, 1, 12) = substr(B.col2,1,12)
  then 1
  on the other
  -for all other cases, when A.col1 is not equal to 'Pete', substr 1-15 must be checked on A and B
  When A.col1! = 'Pete' and substr (A.col2, 1, 15) = substr(B.col2,1,15)
  then 1
  0 otherwise
  end) = 1
  
  When I run the whole application together, he continues to run forever and I finally have to kill him. However, when I run the 2 WHEN clauses separately, it runs within a second and get me the correct data. What's not all by merging these two inside 2 WHEN clauses that it causes the query to drag?
  
  
  Please notify.
  
  Thanks in advance.

  Not sure

  Do you mean that you need much counts separately? or a combined County?

  How you unite their alpha and beta tables? What is the join condition?

  you need to do something like that,

  SELECT COUNT(CASE WHEN
                      (A.col1 = 'Pete' AND SUBSTR(A.col2,,1,12)=SUBSTR(B.col2,,1,13))
                   OR ( A.col1 != 'Pete' AND SUBSTR(A.col2,,1,15)=SUBSTR(B.col2,,1,15))
                  THEN 1 ELSE 0
               END)
  FROM alpha A, beta b
  WHERE alpha.join_cloumn= beta.join_column
  

  G.

• I a s 6 more and when using the phone, if my face touches the screen it clicks on the logout button and the phone hangs up the call. Is it possible to prevent this without holding the phone away from my face when calling?

  I a s 6 more and when using the phone, if my face touches the screen it clicks on the logout button and the phone hangs up the call. Is it possible to prevent this without holding the phone away from my face when calling?

  iPhones have a proximity sensor which is supposed to automatically turn off the screen when you hold it in your face. If this is not the case you can take the phone and have it checked.

• How link to or use the CDN from Adobe After you publish your project?

  So maybe I'm stupid, but I can't really find any useful info on actually works this edition of CAN...

  It's White edge animated API adobe books (also just below him in the section on the HTML pages, I think they are missing from the header of a word in the first sentence... kinda funny - API JavaScript Adobe Edge animate CC)

  Accommodation CDN

  With the help of Adobe Content Distribution Network (CDN) is a great way to speed up the delivery of composition Animate. Compositions using the CDN from Adobe all share a unique URL for jQuery and the Runtime of edge. The cache of the browser execution, so that the user downloads only the library once no matter how can animate compositions they discovered, even the compositions are on different sites and produced by different authors. Does not use the CDN if your composition should work without an Internet connection or if you want to use your own hosting exclusively.

  The Runtime CDN animate using the following URL:

  <script type="text/javascript" charset="utf-8"    src="http://animate.adobe.com/runtime/4.0.0/edge.4.0.0.min.js"></script>

  I mean this all sounds good! So, how to use it? I don't see a place prominently in this URL to replace it with what would be the link to my project? Also, I have not all the numbers I could put in a URL to get the appropriate content unique identification. Shouldn't I have an ID unique? Measure out how what is mine? Maybe I don't really understand how it works...

  My goal is to have this nice little animation I did in the game of edge when someone visits the Web site and then blend in the homepage. Is this possible? It would be great if I could just put some script links in the header and let the adobe CA take care of all aspects of delivery and to keep my load on the server down rather than upload the files myself and have to use extra bandwidth.

  Thank you very much!

  Hey there,

  The CDN from Adobe hosts only animate them DURATION and jQuery Javascript files required (mentioned below), which means you do not have to include in your HTML directory on your server. You will still need to accommodate code HTML and other .js files that creates Animate on your server. Those that are specific to your project.

  When you publish to the web, by default you will be connect Adobe CDN, which hosts two files only:

  Edge.4.0.0.min.js

  jQuery - 2.0.3.min.js

  These files are not unique to your project - each publication Animate uses these files, and each contains the same exact data: they help make HTML files animate to "do what they do" with the movement and interactivity.

  If for any reason any you would bind to the runtimes files on Adobe CDN, you can uncheck "Host runtime files on Adobe CDN" and publish for the new website. A "edge_includes" folder will be created at the root of your web site publish the folder that contains the two files above.

  HTH,

  Joe

• Single line vertical when using the ADF to Scan or copy on HP Officejet Pro 8600

  Printer HP Officejet Pro 8600 Premium (CN577A)

  OS: MS 7 64-bit

  When you use the ADF for my printer HP CN577A Officejet Pro 8600 Premium, I get a single vertical line on the document which is produced. This occurs when copying or scanning, both black and white and in color. If I scan or copy using the glass, I do not get the vertical line.

  I already tried troubleshooting.  I unplugged the printer, left without electricity for several minutes; that didn't fix the problem.  Then, I cleaned the rollers and glass; I always get the vertical line, but only when using the ADF.

  My firmware version is up to date (CLP1CN1150CR).

  What should I check next?

  The only difference between the ADF and scanning flat, from a point of view of the scanner is there on the glass, it happens.  I suggest you get a bright flashlight and examine the corresponsing area hence is the line, it's almost certainly a spot on the strip of thin glass which is being just in the right place.

  I've seen some people suggest that put a flashlight almost parallel to the Strip, it shines from the bottom can highlight the area problem.

• I can map a public IP address on a pc using the router tplink?

  I can map a public IP address on a pc using the router tplink?

  Moved from the community involvement Center

  Original title: Port forwading

  Check with the support of tplink.

• How could I give priority to my network connections, (without turning off the strap attached, as it took), so that it uses the internet from my main network connection?

  Prioritize network connections

  OK, here's the situation.
  I have a regular ethernet connection that provides me with a network and the internet.
  I have also a tablet PC which I attach to my PC so I can use it as a controller. (Not that it is important, but it's for a DAW/Midi controller)

  My problem is that whenever I place my tablet, PC starts by ignoring my normal connection and taking the internet from my Tablet (even when it is not connected to the internet). As a result, my internet is de-energized once I tie it, if I'm not as under the wifi on my tablet.

  My question is, how could I give priority to my network connections, (without turning off the strap attached, as it took), so that it uses the internet from my main network connection?

  Hello

  As well as the troubleshooting provided by Boumediene steps, you can also try the steps in this link. Some screenshots are also available on the link for a better understanding.

  http://www.howtogeek.com/HOWTO/27994/how-to-change-the-priority-of-wiredwireless-network-cards-in-Windows/

  Hope you will find this is useful.

• How to find the IP address of the router from my computer in Windows 7?

  What is the best way to find the IP address of the router from my computer in Windows 7? I know not how to make using the start > cmd > ipconfig, but is there a way to do it with just the mouse?

  Right click on the WiFi icon or-> LAN in the system tray click on open network and sharing Center-> click on "Wireless network connection"--> details click-> see item highlighted on the screenshot:

  

• What type of layer should be used when using the effects lighitng filters "I can't using the way I expect to work -

  What type of layer should be used when using the effects lighitng filters "I can't using the way I expect to work -

  I want to add lights to he image - and to inform the parties of the image - I duplicated the layer add the lights in the filters, but it does not act as a process additive-

  Check out this tutorial from Phlearn on YouTube. It is a bit more flexible, but, of course, requires a bit of elbow grease more Photoshop-wise.

  Create beams of light in Photoshop - YouTube

  Using this technique, you can adjust the 'lights' as you want by manipulating setting masks. See screenshot below. (Still once again, excuse the butchering.)

  

• How to use the adapter from the wall with my Mac Pro laptop?

  How to use the adapter from the wall with my Mac Pro laptop?

  The AC wall connector is not compatible with the outlet on the MBP?  As the MBP charger will work from 100v to 240v, a transformer is necessary.  You need a converter that connects to the power outlet home and is compatible with your MBP.  You can buy the Apple travel kit:

  http://www.Apple.com/shop/product/MD837AM/A/Apple-world-travel-adapter-Kit

  Or you can use a single specific converter for the geographical area:

  http://www.Amazon.com/orei-grounded-universal-adapter-Singapore/DP/B004SCSV2U/re f = sr_1_4? ie = UTF8 & qid = 1460735377 & sr = 8-4 & keywords = us + in + uk + power + adapter

  (it is a UK USA example)

  Or you can get the converter that adapts the charger directly:

  http://www.Amazon.com/HIOTECH%C2%AE-extension-charger-connecting-specification/d p/B00MA48JZW/ref = sr_1_3? ie = UTF8 & qid = 1460735486 & sr = 8-3 & keywords = us + in + uk + power + ad aptor + apple + charger + cord

  (again, this is for a UK plug.)

  Ciao.

• Satellite A100-549: BSOD after I used the recovery from another PC

  Hello.

  Had a few probs with my laptop and decided to recover it using another pc recovery disc.
  I get the laptop is a Toshiba a100-549. Unfortunately for some reason I can't disks that were originally with her.

  The opertaing system is Windows xp. The disks I got with a Vista.
  It loads OK but goes to a blue screen after 30 seconds and restarts. Is there a reason for this and can I do.

  I think I may need to get your hands on a good drive and load it on again.
  Someone at - it copies of drives for this laptop and able to send me their. I'll gladly pay for them...

  Colin

  Hello

  Don t user recovery drive to another PC, because it won't work.
  You can use a clean Windows OS disk or the Toshiba recovery disc.

  Why? Because the recovery disk contains an image. The image is a package containing a Windows OS, drivers and other software.
  If you want to use the recovery from another PC disk then all the drivers, tools and software distributed for this PC will be loaded on your Toshiba laptop.
  This can cause the BSOD!

  So if you n t have the Toshiba recovery disc then you should use MS Windows CD!
  Toshiba drivers can be downloaded from the Toshiba page!

• I6 fire babysit device when using the internet? any solution?

  I6 fire babysit device when using the internet? any solution?

  Let's define "overheating". If the temperature of the phone reached a dangerous level the phone turns off it to cool down. This phenomenon occur? If this is not the case it is not overheated.

  What is your cell signal? If the signal is low, the phone must increase its power to maintain a connection. This may require as much as 10 times the energy as a strong signal, and the phone gets hot under these conditions. If will also drain the battery very quickly.

• Satellite A200 - IE7 windows 'restore down' when using the Tracker pad

  Hi, I recently bought a Satellite A200 - 1VO and when using the laptop without a windows mouse explore 'restore down' at random.

  I found a thread on the site of the Internet USER who said that if his past not with a mouse, it may need tracker drivers up-to-date.
  You can also consider its under warranty.
  Any ideas anyone?

  Hello

  It s a bit confused what you´ve writes down. What do you mean exactly, where´s the problem and what you want to tell us when writing:

  > and when using the laptop without a windows mouse explore 'restore down' at random.
  >
  > I found a thread on the site of the Internet USER who said that if his past not with a mouse, it may need tracker drivers up-to-date.

  Whereas it should be, where´s now the problem?

  Please give clear and understandable feedback, then I and other users you could point to the solution.

  THX

• OfficeJet Pro 8600: Officejet Pro 8600 leaves black lines on docs scanned when using the document feeder

  This is the second HP Officejet Pro 8600 I had - one was replaced by HP, after that the same issue arose.  I tried to clean the entire unit, but we still get a thin black line running vertically down the page.  This line is divided into sections of 1 "and 2.5" in length.  Sometimes I get the fine line and then almost a shadow line that is parallel.

  Any suggestions would be very appreciated I have scan documents to PDF format and it's hassle to put everyone on the flat for scanning.  I use the charger of the doc on a daily basis and wonder if this could have something to do with the lines.

  Thanks for any help.

  The question is a spec on thin (~ 1 "wide) glass to the left of the main bed scanner.  Clean this area as described in this document.  It can be difficult to see the affected area, a bright flashlight which is held at an angle to the glass can help find the place.  Even a very small spec on the glass can cause a black line when using the ADF.