Slower than other computers on the wireless network

Similar Questions

• Satellite A30 does not see other devices in the wireless network

  I recently bought a Toshiba Wireless LAN Mini PCI Card, I installed and was able to recognize my broadband, but he does not see the other network devices. I have not provided with drivers or software for the operation of the card (I bought a decent retailer). Can you recommend me to downloads that would be this card?

  I have a laptop of Satelite A30 1 GB ram 60 GB HDD.

  Large files sometimes also stop transfer (crashes) when you use my USB connection. The usb controller uses the driver microsoft 5.1.2600.0 dated June 1, 2002.

  Is this a driver problem?

  Hello

  If the wireless network adapter is properly installed if you have not configured you.
  I put t know which devices in broadband services, you want to say but generally if you want to communicate or transfer files between laptops through the WiFi network so all the computers must be in the same domain or workgroup.

  I can't give you a correct answer, but only a suggestion. I have red that sometimes a lower potency could be responsible for this show. Try turning off the safe power option in the properties of the hub USB root in Device Manager.

  Hello

  If the wireless network adapter is properly installed if you have not configured you.
  I put t know which devices in broadband services, you want to say but generally if you want to communicate or transfer files between laptops through the computer WiFi network so all must be in the same domain or workgroup.

  I can't give you a correct answer, but only a suggestion. I have red that sometimes a lower potency could be responsible for this show. Try turning off the safe power option in the properties of the hub USB root in Device Manager.

• CAN´t find other computers on the home network Windows.

  I have a home network windows already defined with two desktop with Windows XP and a laptop with Windows 2000. The computers are connected to a router with ethernet cables and the lap top wireless (WiFi) to the same router. Now, I'm trying to connect a fourth computer (a desk top) with Windows Vista. It works fine to connect to Internet, but I can't reach the other computers on the network. On other computers, I can see a 'new', but I don't see the others of a "new". Can someone help me with the configuration of the computer "Vista"?  Thanks in advance.  / Thomas

  Hello
   
  To home network computers running different versions of Windows, we need to make sure that what follows.
  a. ensure that all computers are in the same workgroup.
  (b) the value of the private network location type.
  c. open ports in your firewall to allow file and printer sharing.
  d. turn on additional file and printer sharing options.
  e. consider using password protected sharing.
  5 using the network card.
   
  The NIC in the network and sharing Center is a graphical view of the computers and devices on your network, showing how they are connected and including problem areas. A computer running Windows XP can be detected and appear on the network map, you may need to install the Protocol Link-Layer Topology Discovery (LLTD) on this computer.
   
  To install LLTD, visit the following link and download: http://support.microsoft.com/kb/922120
   
  For more information on the "networking running different versions of Windows' computers, visit the following link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/Networking-home-computers-running-different-versions-of-Windows
   
  I hope this helps.
   
  Kind regards
  Syed V
  Answers from Microsoft supports the engineer.

• WRT110-cant connect 2 computers to the wireless network at the same time

  I recently got this modem-

  It works very well with a computer, but if you are trying to connect to the network wirelessly with a second computer the connection is lost for both computers.

  A computer is a macbook pro installed osx 10.5.7 is either a computer dell laptop on vista

  First of all, you should get your router updated firmware...

  Download 2.77 MB firmware...

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave the name blank username & password use admin lowercase...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• Premium 8600 Pro Office jet: Officejet pro 8600 not found by computers on the wireless network

  Hi all!

  I had this problem and goes out at least once a year...

  When I go to print on any computer through wireless connections, computers can't find the printer.  The printer is turned on and connected to the network, and network results show that everything is fine.  I did everything, including restarting the printer, by restarting the computer tries to print the form and reinstall the printer, and I get the message "Printer" not logged on computers.  Each moon blue, if I leave it long enough, he will find somehow the printer and printing, but as I said it's extremely rare.

  Logistics-wise, I am using Comcast for cable internet, and are all Apple products.  The modem is a Motorola and the router is a Linksys.  The router is less than 25 feet from the printer, and there is a clear shot-not walls or to block the signal

  Thanks to all of y ' alls for help!

  Hey @jgossc,

  Welcome to the Forum from HP Support.

  I see that you experience the Mac-to-printer communication problems. I want to help you with this. I have some suggestions that might help.

  I recommend you try the following steps:

  • Uninstall your printer - click here for instructions.
  • Fix permissions of the disc on your Mac - click here for instructions.
  • Once you have finished running the utility above, restart your computer.
  • Finally, click here to reinstall your printer using HP Easy Start.

  If you find the connection of the printer is more coherent then fine. If this is not the case, click here for detailed instructions on how to address the issue. In particular, it may be useful to clarify the matter once and for all from affecting a static IP address. Please let me know the result of your troubleshooting by responding to this post.

  If I helped you to solve the problem and that you liked this post, feel free to express your thanks by clicking the "Thumbs Up" icon below by clicking on "accept as Solution" (this will help others find the solution).

  Thank you for being a part of the community of HP.

  Have a great day!

• Printer does not work with computers on the wireless network

  Yesterday I went to the HP site and downloaded the rcommended drivers associated with my Win 7 computer and printer Officejet 7310.  Since then, I can't print at all.  My other laptop connected to the network (Win Vista) will not be printed or the other.  My computer says that my printer is offline.  How can I get these devices to talk to another new

  Two printers working now!  Thanks for the help

• network printer shows off line but printsf by other computers on the network

  my brother mfc-7840w printer displayed offliine when I try to print from a computer on a network, but works fine on other computers on the same network. I remove and reinstalled printer. Works for a short time but when computer turned off and rebooted the printer go offline. a stop printer, etc.

  Hello

  Follow the steps in the link below and check if it solves the problem.
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/network-printer-goes-offline-on-Windows-7/df4321de-EE25-423F-b1c9-d38957d50131

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• problems re-connecting to the wireless network

  Running vista on new hp computer, printer is hp deskjet 3052 was that was connected and working just fine and all of our other computers on the home network wireless could access the printer. Lost connection for some reason after working for almost a year, now try to get it back. Ran test wireless network and wireless is lit, wireless work pass, under network, he said the network name (ssid found)... IN CASE OF FAILURE. So under the current confiruration it says network name (ssid not defined). How to reset it? We recently changed internet providers so I know that we need to define the new network on the rise but don't have the installation disc or the manual. Thanks for any help.

  Hello

  Please see the following document on how to configure the printer on the network.

  http://support.HP.com/us-en/document/c02722113

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• HP Laserjet 200 M276 Color MFP: HP Laserjer 200 color than MFP M276 found on the wireless network

  Printer is connected to the wireless network, but cannot be seen by the computers on this network.

  The printer has been installed on my home network for 6 months and works well.  Now it is found on the network.  Power cycle the printer, and he started to work for one night.

  The day after the printer is found on the network by PC, running Windows or Mac 8.1 on the network (under Leopard through Yosemite.

  Reset printer settings by default, in the wireless network data and verified that it is on the network (wireless diagnostics confirm the network name, config, port and switch Diagnostics).  Still cannot be found on the wireless network.  I know that it is on the network, because it can access internet functions.

  Repeated configuration via USB for settings wireless program.  Receive error message indicating the wireless settings have been communicated successfully to the printer, but the printer is not found on the wireless network.

  Not cool.  Looks like I have yet another broken HP printer.  I don't know the process.  I called the warranty and they are sending me a refurb printer.

  Returned to the HP after 10 years.  Looks like it was a mistake.

  Hello

  Try restarting your router by unpluggin power for a while, let him 3 minutes to start and restart the printer.

  Click the icon on the printer wireless - what is the listed IP address?

  Can happen that the intellectual property of the Explorer of your computer?

  You can see any difference after the reboot of the router?

• I am not able to connect Stor-E for the other computers on my home network

  I just bought a Stor-E but I can't connect to other computers on my home network which I think is a Netgear router which is connected to my BT home hub.

  I can access the stor-e of my laptop and pc, but cannot access the Stor-E when I go to the working groups then on my PC it calls for a Net User ID and password have tried my user id and password for my pc but this doesn t seem to work.

  Someone has an idea what I am doing wrong?

  But in general your Stor-E works correctly when you connect it directly on different computers, right?

• FOJ 8500 909 g will not fully install, not accessible from the computers in home wireless network

  I bought an Officejet Pro 8500 909 g which worked well on our home network for 18 months.  Desktop is 32-bit Windows 7 with a USB cable.  Two wireless devices are 64-bit Windows 7.  Printer suddenly has not recognized the cartridges and frozen with the message "problem with the ink cartridge.  Called HP (unassisted) and tech support of holders of the contract of service - without help.  They sent a refurbished (even) model which I can't install on USB or wireless connection completely.  Yesterday, I was able to print at least one 3 machines on the network (not every machine wireless).  Today, I can not print even the USB device.  5 days lost uninstall then reinstall the printer software, router, etc.  Connected wireless network.  Printer says it is on the wireless network.  HP Solution center is not accessible because the "printer is not completely installed. Help?

  Hi EWQuince,

  The information you have given it seems that the printer is not on the same network as the computer. If the printer was on the same network as the computer, the IP address would be 192.168.1 instead of 192.168.33. You must run the printer Wireless Setup Wizard and make sure that you connect it to a network, the computers are connected. Once you have the printer connected to the same network all your problems should be solved.

  To connect to the wireless network

   

• Cannot see other computers on the network

  Am on XP SP3.
  When I go to network connections,
  Right-click on local area network
  Click Properties under the general tab,
  Click on install and click Service
  .. all I see is a list for a McAfee driver but nothing for Microsoft. I removed my computer some time ago with McAfee & he must have created problems that I can't see other computers on the network. Is there a Microsoft driver, I need to install and which will help to solve the problem of not seeing other computers on the network.

  On the general tab of the properties of your network connection to the LAN card, you should see a box under the heading "this connection uses the following items."  Most Windows XP configurations for home use have 4 entries in this box: Client for Microsoft Networks, QoS Packet Scheduler, file sharing and printers for Microsoft Networks, and Internet (TCP/IP) Protocol.

  If you don't have these, you need to install, even if you really need not the Scheduler of QoS packages.

  You seem to have got almost to the right place, but be aware that when you click on the button 'Install' in the box, you are given 3 choices: customer, Service and Protocol.  The "Client for Microsoft networks" is obviously a "customer." 'Internet (TCP/IP) Protocol' is a 'Protocol' and the other two are "Services".

  What elements you have installed?

• WRT160N - can't see other computers on the network

  I installed a new WRT160N and now I can't see other computers on my local network, but I can access the internet on each of them.

  Y at - it a setting that I need to change or what I need to use static IP instead of DHCP addresses?

  If you cannot ping the other computers on the network, then check your firewall settings or any other security software blocking the connection.

• Windows Vista detects the wireless network but will not connect to it. Two other users in the same office connect without difficulty.

  The title says it all really.

  I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.
  Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.
  Help, please.
  Thank you.
  original title: vista detection network but will not connect

  Hi JulianBeach,

  1. you have made no changes to the computer before the broadcast took place?
  2. What is the exact error message you get?
  3 is connected to the domain of the computer?
  4. what happens when you try to connect to the network?

  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions