Small business router for Skype QoS

Similar Questions

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• One-to-one NAT and small business routers

  Hello all, can anyone tell me if there is any router for small businesses that offer a NAT?

  Here's what I do: I have several IP addresses public Qwest has given me. I have two servers that provide e-mail and web hosting for two different areas. I want to put the client machines on a LAN VIRTUAL (VLAN Z) and assign a public IP address (to separate traffic from the server). I want to put every server on its own LAN VIRTUAL (VLAN & XY) and assign to each its own public IP address server. I need the router to be able to provide a firewall and port forwarding for each VLAN. I also need to be able to carry traffic between VLANs for VLAN Z customers may access their e-mail and websites on VLANs X and Y. I have also need to be able to send DNS traffic between the VLANS so each server can provide resolution of names for their respective areas.

  So, is this possible with a small business router or I have to watch something different? I am pretty sure that this configuration is not possible with my current Cisco RVS4000. What it boils down to is that I need a router that is able to have multiple public IP addresses on the same interface and pass the public addresses to subnets private VLAN. It would be a NAT, as I understand it... right?

  Any help is greatly appreciated!

  Hi Taylor, please use our forum, my name is Johnnatan and I'm part of the community of support to small businesses. I ve seen your post and I was looking for some devices that could help you, these small business router supports the functionality you were missing, the one-to-one nat, also the routing features, you see the list of routers Rv here

  http://www.Cisco.com/en/us/products/ps9923/products_data_sheets_list.html

  I chose two models that may be useful for you:

  Rv180

  http://www.Cisco.com/en/us/prod/collateral/routers/ps10907/ps9923/ps11995/C78-697397_data_sheet.html

  Rv220

  http://www.Cisco.com/en/us/prod/collateral/routers/ps9923/ps11025/data_sheet_c78-630461.html

  I hope you find this answer useful,

  * Please answer question mark or note the fact other users can benefit from the TI *.

  Greetings,

  Johnnatan Rodriguez Miranda.

  Support of Cisco network engineer.

• Small Business Investment program Question

  I have a question about the small business investment program. I just bought a Cisco Small Business router and additional Small Business 8 Port Switch. Later on the road, we might need a 16, Port or more, but we don't need to exchange any now. We wonder what it takes just to enroll in the program. What is the link you need to register?

  http://ciscoinvestmentprotection.com/register.html

  Thank you!

  Hi Nathan,

  I just noticed that you also tweeted on the subject.  Anyway, here's the URL that you should go and look for information about this program:

  http://ciscoinvestmentprotection.com/brochure.html#

  Kind regards

  Cindy Toy

  Cisco Small Business Community Manager

  for Cisco Small Business products

  www.Cisco.com/go/smallbizsupport

• Windows Small Business Server Remote Desktop connection

  Original title: Remote Desktop connection

  I am using a remote connection, but I get this error message. What it means and how to fix it?

  

  Hello KidateLirame,

  Based on the provided screenshot and online information, I searched this problem seems to be related to Windows Small Business Server, for better assistance on this issue, I would recommend that you post the question in the Windows Server Small forums.

  Here is the link for the same thing.

  http://social.technet.Microsoft.com/forums/en-us/home?category=SBSServer

  Thank you.

• My small business SF 302-08 Switch will not let me apply the command "Routing".

  Hi everyone, my switch cisco small business SF 302-08 has the latest firmware and I want to activate the command routing, but it doesn't let me do that.

  I've read the reference guide for orders, do all this procedure: IP Routing Protocol independent commands starting at page 629, but nothing happens. I need this because I want a routing between VLANs

  Kind regards.

  Hi Felipe

  Look forward to hearing how you go.

  If you reset the factory default switch and the switch is NOT connected to a server, the switch restarts with a default IP 192.168.1.245 address according to the Quick start guide .  If your PC has a static address 192.168.1.2, you should be able to access the graphical interface of the switch.

  http://www.Cisco.com/en/us/docs/switches/LAN/CSBMs/sf30x_sg30x/Quick_Start/78-19252-01.PDF

  If the switch is connected to a DHCP server, the switch Gets an IP via DHCP.

  I've had problems using hyperterminal on my Windows 7 box, that I have overcome by restarting my PC in order to free the COM port.  Settings of the console are;

  • 115200 bits per second
  • 8 data bits
  • no parity
  • 1 stop bit
  • no flow control

  If you really have problems, and you think that the switch is faulty, you have the possibility to use the services of small business Support Center (HWC) in order to identify if the switch is good or bad.

  The URL that watch phone numbers are lower;

  www.Cisco.com/go/SBSC

  Best regards, Dave

• Router Cisco Small business with the functionality of the link aggregation

  Hi all!

  can someone tell me if there is a router from Cisco Small business with the functionality of the link aggregation? (I want to connect two 4 Mbps SDSL for flow)  The RV082 can do?

  Best regards

  You would need a RV016, who takes in charge up to 7 WAN ports. RV082 has only two WAN ports.

• R8500: QOS is terrible on this router for $400

  So before you get this router I was using a $20 off of eBay refurbished Linksys router E6500 running DD WRT (Yes, you can run it on this router if you know where to find the firmware for this). In any case, the flow was not the greatest, but I never had problems.

  I have a ReadyNAS RN516 to my office and the backup on my Mac using the time machine office nas. I also have the Charter which gives single 4mbps upload (it's slow, but once he finished the initial and subsequent backup backups are fine). In real life, it's more like 4.75mbps. I have QOS value 3.75 to ensure that my modem is not bufferbloat and kill my connection.

  My problem is however that often my devices slow to a crawl (if more than 5 Ghz wireless or wired) whenever I am downloading. On my other router I just put 4 Mbps as the download limit and all devices than 4mbps equally, and I never had no problem with slowdowns or high pings and lag. No matter what I put the download speed at... He accuses just out for no apparent reason on this router.

  If someone can tell me why free DD WRT software works better than the software on a router for $400? Just curious?

  The new firmware seems to have helped. I changed a few things as well, and it seems to work very well.

  Regarding the comment of routers figure 3 and 4 routers in figure, there must be an improvement on the 2 figure routers and routers multi-3, otherwise what's the point?

  I'm trying the test of the future a little, that's why I chose this router. It doesn't matter if I take it right back and stick with my $ 20 DDWRT router. I do not have the latest and greatest tech (2012 macbook air and several iPhone 6 more ' and a room above the router and I can not even through any speedtests 60mbps (run through the gigabit mac that is wired and I move 65mbps each time.)

  I don't have a fast enough home nas box, but I'd be curious to see wireless local area network speeds. I wonder if I can break even 100 Mbps with this thing...

• best configuration for Small Business Server

  I'm looking for advice on HW and SW recommendations for a small business.  We have 15 users, 20 computers and 3 printers.  I currently have a single Windows Server 2008.  I want to run a domain controller main for all users, file sharing, print server, possibly Windows Update Center and eventually MS Exchange.  I am trying to decide the best configuration of HW with a fairly cheap budget.   I currently have 1 I7 based server with 4 GB of Ram, several IBM servers, P4 306 m (I have 4 +), and a lot of hard drives (all in a half rack).  I also need a decent backup system.

  Can anyone recommend the best configuration of HW player and hard?  Should I analyze server roles?  With respect to the SW, I'm a non-profit and use Windows Server 2008 (at a discount)

  Thank you

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you.

• We stil run an extensive system of Small Business Accounting. I wonder what others have opted for now his party and support.

  We stil run an extensive system of Small Business Accounting.  I wonder what others have opted for now his party and support.  We have to find a new solution.  Recommend something?

  Shane

  original title: Small Business Accounting

  Try: QuickBooks

• How to change the record to a local drive on network drive for all users (Small Business Server)?

  I need to implement a change on the backup to a local drive to save to the network drive/folder to 15 users in a Small Business Server, can someone help?

  Thank you

  Hi Frydom,

  Your question of Windows Server is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Server forums.

  http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

• Query for windows small business server 2008 SP1

  Hello

  I have windows small business Server 2008 SP1, I am installing the additional DC for windows small business server 2008 on another server, I gave the DC ip addr as 192.168.1.2 subnet 255.255.255.0 Gateway 192.168.1.1 and 192.168.1.2 dns. On another server where I am trying to install AD DC 192.168.1.3 ip subnet 255.255.255.0 Gateway 192.168.1.1 192.168.1.2 dns... By running the dcpromo and the replication active directory, the installation is in error during replication... the error is

  Active directory could not install,

  Replication failed to allocate memory.

  cmd prompt nslookup also displays the server ip and domain name. Then any body tell me, if we can install AD DC for small business server 2008, and how is this replication error could not allocate memory. How to solve this error.

  Your comments will be appreciated

  Hello

  I have windows small business Server 2008 SP1, I am installing the additional DC for windows small business server 2008 on another server, I gave the DC ip addr as 192.168.1.2 subnet 255.255.255.0 Gateway 192.168.1.1 and 192.168.1.2 dns. On another server where I am trying to install AD DC 192.168.1.3 ip subnet 255.255.255.0 Gateway 192.168.1.1 192.168.1.2 dns... By running the dcpromo and the replication active directory, the installation is in error during replication... the error is

  Active directory could not install,

  Replication failed to allocate memory.

  cmd prompt nslookup also displays the server ip and domain name. Then any body tell me, if we can install AD DC for small business server 2008, and how is this replication error could not allocate memory. How to solve this error.

  Your comments will be appreciated

  Hey AAAAAAAAAAAAtif

  It's an instance of vista installation

  Try the link below sbs forum

  This forum is for General Discussions on Small Business Server 2008, R2, 2003, 2003 SP1, 2003 and earlier versions. Gateway available NNTP Client if you wish to participate via a Newsgroup Reader. Read the sticky at the top of the forum Post.

  http://social.technet.Microsoft.com/forums/en/smallbusinessserver/threads

  Walter, the time zone traveller

• Small Business Accounting 2006 for Vista download

  I am trying to download my 2006 version of MS small business accounting on my NEW computer which has Windows Vista as operating system. I downloaded all updates and it still not open. I click on the software, and it shows that it is opening. Then he said that a problem caused the SMBA to stop working and MS will give you a solution for the program and it will stop runnng but then I don't get any information.
  I checked all of the patches that I can find and that are related to this issue. Help! Thank you!

  Hello Miranda,

  Thanks for posting on the Microsoft answers Community Forum.

  Your version of Microsoft Small Business accounting 2006 is not compatible with Windows Vista.  You can view the compatibility of the software with Vista on the compatibility of Microsoft site. http://www.Microsoft.com/Windows/compatibility/search.aspx?type=software&s=small%20Business%20accounting%2023006&page=6

  However, you are eligible for a free update to Office Accounting 2009 if you have a licensed copy of your software in 2006.  Existing customers who have a license for 2006, 2007 or Microsoft Office Accounting 2008 are entitled to a free upgrade of 2009 Accounting Office. Please refer to the URL below to determine your upgrade path.

  http://www.ideawins.com/upgrade.aspx

  I have also included the link on how to upgrade to Office Accounting 2009. It is recommended that you back up your current data in Small Business Accounting 2006 before the upgrade. If your SBA 2006 should not be SP2, you may need to upgrade the service pack before the backup.

  http://www.ideawins.com/UpgradingFromSBA2006.aspx

  Once you have upgraded and loading your data, you might want to consider uninstalling Microsoft Office Small Business Accounting 2006 (SBA). SBA uses an older version of SQL Server called MSDE (Microsoft SQL Server Desktop Engine), and that your computer will run faster if you uninstall SBA and MSDE.

  Please post again if you have any questions or concerns.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Fundamental issues of SFP for Small Business Switches

  Hi all

  Just for fun, I would switch to fiber, running the trunk ports between my two Cisco SG300 lab switches but I'm new to the media.

  In looking at the options, I thought that MM (MGBSX1) is the way to go, but the cost of the 'Official' FPS an arm and a leg. (don't forget, he is my laboratory, not a production environment).

  I have a few newbie questions and forgive if this has been answered a hundred times, but I was not able to find in the search.

  1. What I really need to use Cisco brand trancievers? I've seen other than Cisco 1000BASE-SX SFP on ebay for a tenth of the cost. Given that, Yes, the quality may or may not be the same.
  2. Is MGBSX1 way to go? Switches are in different rooms, so distance is not a problem, my choice was based on cost trancievers and media.
  3. SFP ports are valued only Gigabit, but I saw a higher number variety quoted. Is this a limitation of the switch itself, the protocol used, or the transmission media?

  Again sorry if these are questions of newb and thanks in advance!

  Lee

  1. should I really use Cisco brand trancievers? I've seen other than Cisco 1000BASE-SX SFP on ebay for a tenth of the cost. Given that, Yes, the quality may or may not be the same.

  According to the Quick Start Guide SG300 ' SFP ports are compatible with Cisco modules MGBT1, MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFELX1, and MFEBX1, in addition to the modules from other brands. "

  2. is MGBSX1 way to go? Switches are in different rooms, so distance is not a problem, my choice was based on cost trancievers and media.

  Choose a type of SFP based on the length of the links and the type of available fiber.  Small Business card SFP provides the information you need.  The MGBSX1 is probably a good choice, low-cost, up to length of 550 meters over multimode fiber link.

  3 ports SFP are valued only Gigabit, but I saw a higher number variety quoted. Is this a limitation of the switch itself, the protocol used, or the transmission media?

  Each switch is designed to support specific port speeds, based on the application of switches designed into the network.  Optical transceiver modules do not support different speeds (like many electric ports).  Instead, the switch port is compatible, the transmitter/receiver module can be swapped to change speeds.  Style SFP modules are available at 100 Mbps and 1Gpbs; Modules of SFP + for 10 Gbit/s; higher speeds have new form factors.  You can see a lot of styles of optical Modules on the page Web Cisco transceiver.

  Good luck!

• Plug-and-Play for Cisco Small Business 300 Series managed switch

  Nice day

  What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?

  It seems there are not, the operating system is not the standard IOS I used to.

  I would use with ability to bridge the Infrastructure first Cisco PnP.

  Concerning

  Stone

  First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.

  Seal a document shows how this is done.

  Hope that the information would be useful.