Solaris 10 VM loses the network after upgrade tools

Similar Questions

• Unable to connect to the network after upgrade to 9.3.1

  I upgraded my iPod Touch 5th gen 9.3.1 and he "lost" the network password.  After many attempts to re - enter, I said the iPod 'forget' the network and tried again and again... Same result: "Incorrect password" - which it is not, as I checked directly with the modem.  Any suggestions?

  Take a look at this Apple Support article:

  https://support.Apple.com/en-us/HT204051

  Reset your network settings.

  Settings - general - reset - reset the network settings

  Reset your device. This will not erase your data stored on the phone.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

• LasetJet Pro M475dn: Impossible to scan over the network after upgrade to El Capitan

  After that I upgraded to El Capitan I no longer use HP Scan or HP Easy Scan to scan the network more. I can print to the printer, but analysis always results in the page being pulled by the document feeder, but applications just to lock-up without the document showing. Everything worked fine on Yosemite.

  I found a workaround solution that once worked before after a update of Mac OS X (but had to change the name of file, much like the original file has disappeared). Just download the next file on HP (no matter that it is not for your printer; it's not mine either (OfficeJet Pro L7680) but it works).
  
  FTP://FTP.HP.com/pub//softlib/software12/COL51752/OJ-125213-3/HP-inkjet-SW-OSX-Mavericks_v12.34.37.dmg
  
  Disable SIP for this installation and when you run the installation program (do not know if you need to do, but I did anyway). To do this, the instructions are here:
  
  https://forums.developer.Apple.com/thread/3981
  
  When you run the Setup program, make sure you hold the CTRL key when you right-click on it, then click Open in the menu.
  
  Run the Setup program. Be sure to select the HP scanning software and install it. When you get to the configuration of the printer, just skip this step (unless you are using the printer in question). The parser components are what you really want from the printer drivers are already in El Capitan, if you have a HP supported printer. The scanning software will have already installed to the moment you arrive at this screen.
  
  Install the HP Easy Scan on the App Store app (if you get the latest version of the software your front-end). You should be able to run the scanner and scans without restart. I don't know if it will work for everyone, but certainly, it worked for me and keep me until they find what went wrong in El Capitan to disable scanning and scanning capabilities.
  
  SIP turn on again so that your Mac is better protected. We should all work after that. After doing the above, I found that I was able to not only use the HP software, I was able to use Image Capture, preview, etc, to get images from the scanner. Your mileage may vary, but if all goes well it will work again for you all.

• Problem with the mouse and the network after the upgrade VMware Tools and hardware to virtual machine

  Hello world...

  I just upgrade my ESX 3.5 servers to vSphere 4.1. All this work is very well with the upgrade right now.

  After that, I tried to mise a niveau of VMware Tools and hardware of VM for my virtual machine and the problems started.

  I tried with two different VM (the two Windows 2003) and the problem appears for the two VM.

  I don't want to test another VM of the different operating system now, I'm afraid to go too far with update of Pentecost the problem I have now.

  I tried two VM to be sure that the problem is not only on a virtual machine.

  First of all, the mouse.

  My mouse has jerky movement. The button works, but sometimes I have to click several times to select what I want.

  I tried to uninstall the mouse in Device Manager and reinstall, but not really Pentecost improvement which (buttons works better, but... not so sure).

  Second problem.

  After you restart the server after VMmware tools and hardware virtual machine, the network link not working anymore.

  When I go to my network card configuration, IP settings are reset in DHCP mode.

  If I go again all my IP settings, Windows says:

  The IP address is hidden from the network and Dial-up connections

  folder because it is not physically in the computer or is a riser

  It does not work. If the same address is assigned to both adapters and

  they become active, only one of them will use this address. This may result

  in the incorrect system configuration. You want to enter a different IP address

  address of this adapter in the list of IP addresses for this card in the list

  Advanced IP address in the dialog box

  If I answer Yes to this, I have to enter a new IP address, and of course, this is not what I want to do.

  If I don't answer, the network working again.

  I think it is a strange message but the work of the vSphere maybe network now.

  Anyone have any idea why my work network and mouse as this upgrade after.

  All other VM that is not upgraded so far works great.

  Thanks in advance...

  (1) make sure that your hardware acceleration is safe enough. I got the upgrade down my hardware acceleration several times already.

  (2) sounds like the new drivers for your NIC cards took over and VMware is basically a new card NETWORK for you. Follow these steps to disable it:

  (a) open a command prompt

  (b) type (without quotes): 'set devmgr_show_nonpresent_devices = 1' and press ENTER.

  (c) type (without the quotes): "start devmgmt.msc"

• HP LaserJet M1522nf begins to lose the network connection

  Hello! I have HP LaserJet M1522nf and I use it for about 1 year maybe, but since last week, he begins to lose the network connection (ping failed, web interface does not work too). To be correct, the printer is connected directly to the network through an ethernet cable, and the cable is perfectly fine. His work when you turn it on and for the next 5 to 15 minutes, but after that it lost connection (tasks start fails).

  I really like using little aid, some perhaps of advice. Any suggestions?

  Hard reset the router to factory settings and reconfigure your settings.  Pass the cable to a different port on the router.  You said that the cable was good... change anyway.  Try now.

• What happened to the flashlight after upgrade to ios10

  What happened to the flashlight after upgrading to IOS 10

  Flashlight is the control center? I swear that I saw on one of these demo phones in an Apple store.

• Cannot use the network after using McAfee antivirus with removal tool

  Original title: Mc McAfee antivirus more removal tool damage my network cards after that I use it, what do I do? McAfee tech say that they are not responsible.

  MC McAfee antivirus more removal tool damage my network cards after that I use it, what do I do? McAfee tech say that they are not responsible. After removing the software and restarted, computer cannot connect to the net (device manager shows problems with NIC miniport McAfee mc?).

  Hello

  Please join Microsoft Community where you can find the necessary information on Microsoft products!

  You can't connect to the network after McAfee antivirus using more the removal tool to remove McAfee software.

  The network drivers is maybe damaged.

  1. What is brand and model computer?

  2. What is error right messagee you receive in Device Manager?

  To confirm that the problem is with the driver, do us reinstall the driver:

  a. click Start, click Run and type devmgmt.msc and press enter

  b. now right click on the network card and uninstall it and restart the computer.

  You can also get the latest version of the driver from the manufacturer.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• HP 200 MFP M276nw not seen in the network after changing router

  Printer: LaserJet Pro 200 color MFP M276nw

  LAN: both PC (Windows 7) and the printer connected to the router.  Other devices connect wirelessly.  Internet service is cable.

  I installed this printer when a router Linksys E2500 was in use.  The configuration of the network after the installation of the printer:

  IPv4 address: 192.168.1.120

  Subnet mask: 255.255.255.0

  Default gateway: 192.168.1.1

  Configured by IP: DHCP

  I replaced the router Linksys with a Netgear WNDR4500 router (N900) a month ago.  Everything worked fine for about two weeks.  All of a sudden, jobs sent to the printer began to take a long time to start to print until they stopped printing altogether.  The printer does not appear as a device plugged (cable) in the interface of the router on the Web.  Not even the HP Print or HP Print software and the Scan doctor could find a printer is connected.

  I have unisntalled and reinstall the printer, but did not succeed until I changed the Ethernet cable connecting the printer to the router.  The difference is that the old cable Cat5e and replacement a Cat6?  It's printing and scanning now but the printer is still absent as a wired device, and I fear that it will stop working once more.

  I noticed that the network configuration of the printer after reinstalling is:

  IPv4 address: 169.254.230.140

  Subnet mask: 255.255.0.0

  Default gateway: 169.254.230.140

  Configured by IP: AUTOIP

  Research on the Web, I found an article saying that AUTOIP could be a sign of problems of router or a cable.  My suspicion is that the IP address of the printer is constantly changing and this is the reason for the delay of printing.

  My questions to the experts are: I could assign an IP address to the printer manually so I can add it in the router - it provides to this effect- and how this is done?   In the Toolbox of device HP under the IPv4 Configuration, there is a dropdown menu with different options - DHCP, BOOTP, AUTOIP, and manual, but I don't know if the changes are made here or if it's a more complex undertaking.

  Thank you very much.

  Kind regards

  Miguel remainder

  I solved the problem, the same day I posted the request for help.

  I've closed everything down - including the cable modem and router - but left the printer.  Go to the printer control panel and changed is manual configuration IPv4 of AutoIP toe.  I had already selected an IP starting with 192, since I read that starting with 169 IP addresses are associated parameters AutoIP.  From there on, the printer has presented a valid subnet mask addresses, I took one, and a default gateway address.  Then I stopped the printer.

  I turned on the modem, router, pc and printer.  The router then showed the printer as a device connected with his newly assigned IP address.

  I figured that the cable was not a problem here, so I put the Ethernet Cat5e cable.  What baffles me, is why the printer changed to AutoIP because it was not made by any user.  Check the reports printed during the first installation of the printer, I see that the method of IP in DHCP address.  After putting in the new router, changes were to name SSID and password in wireless devices and found the firmware of the router.

  It was learning by trial as I'm not a computer expert, but so far, we print and scan documents.

  Thanks to all who took the time to read the post and offered help.

• HP 8600 printer range is found on the network after you have installed the Dymo printer for processing of credit cards

  HP 8600 printer range is found on the network after you have installed the Dymo 450 Turbo printer for processing of credit cards

  Hello Christina,

  1. What is the IP (Internet Protocol) address, the subnet and default gateway of the printer?

  2 have you tried to Ping to the IP address of the printer?

  Reset the printer can help get the problem solved.

  Perform the steps mentioned below to get the address of IP(Internet Protocol), subnet address, and default gateway.

  a: Type CMD in the search box start and press ENTER.

  b: now, type Ipconfig/all and press ENTER.

  Proceed as for Ping to the IP address of the printer.

  a: Type CMD in the search box start and press ENTER.

  b: type PING (IP address of the printer) , and then press ENTER.

  Reset the printing system:
  a: Go to System Preferences > Print & Fax
  b: Right (or control), click inside the box that lists your printers and select Reset Printing System.

  WARNING- This will remove ALL your printers!
  c: Select the sign more to add a printer. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

  Click on the link mentioned below as reference.

  http://Windows.Microsoft.com/en-in/Windows7/install-a-printer-on-a-home-network

  Note: "Check the title that reads" set up a network printer "

  Answer please if you have any questions.

• Microsoft Windows Nokia Lumia640 LTE Denim loses FlashPlayer & IE11 after upgrade to Win10 Mobile overview

  To the right; After upgrading my Microsoft Windows Nokia Lumia 640LTE Denim phone Win10 mobile preview, I have function no. FlashPlayer available onboard, that shows any ad or the option to turn on or off in the settings of parameters / advanced as it should. It also, since the upgrade, omitted the option to block pop ups as well. The Explorer11 of the Internet also failed to appear after upgrading to Win10 Mobile preview, which, like Flash Player, is supposed to be incorporated. I did a hard reset without success, as again after the first upgrade to Win10 Mobile Preview, the second re-installation gave the same results.  Help, please! Thank you!

  Hello

  I have answered your original question: Flash Player only is not supported on mobile devices, including Win10 Mobile, only devices dekstop.  See Adobe Flash Player | Technical for the supported platforms.

  I don't know how and why it may have worked before the upgrade to Win10 Mobile Preview, but Flash Player has never been supported on Windows Phone.  Maybe it was something that Microsoft does. I recommend you contact Microsoft support for assistance.

  --

  Maria

• Problem with the mapping of the keyboard after upgrading to Fusion 7

  Hello

  I noticed that the keyboard layout has changed in the comments after the upgrade to VMware Fusion version 6 to version 7, even if nothing has changed in the settings "Region and language" in comments Windows 7.  Keys that have changed are "------' with ' < ' and ' | ' with ' > ' everything is OK. The keyboard is configured in Italian

  All the world has noticed the same problem?

  Have you solved?

  Thanks in advance.

  The problem has been resolved by the technical support of vmware with a workaround. They know that the question on the keys is interchangeable in the VM after upgrade to Fusion 7.

  Their development team is currently working on this issue on the priority. This will be fixed in the next update.

  However, they have a work around for the problem of keyboard. Following the instructions below to map the key manually in VMware Fusion.

  : Note make a note of the interchangeable keys in Windows before you enable the mapping of the keys.

  1. click on VMware Fusion-> preferences-> keyboard & mouse-> mappings of keys

  2. make sure that 'Enable key mappings' is enabled

  3. click on '+' sign at the bottom

  4. press the key that you want to send from the text box Mac keyboard

  5. press the key you want to receive on the VM in text box

  Note: You can also use the combination of change, control, Option, command if necessary.

• How can I reinstall the CS6 after upgrading Windows Vista to Windows 10?

  How can I reinstall the CS6 after upgrading Windows Vista to Windows 10?

  Hello

  You can download the Photoshop CS 6 from the below mentioned link.

  Download Creative Suite 6 applications

  Thank you

• Problems in connection to the mobile network after upgrading to iOS 9.2.1

  Upgrade to iOS 9.2.1 Thursday last on my iPhone 5. Mobile connectivity random but frequent problems faced since then - just lose network connectivity and the phone displays "No. Service" for long periods. Are gone to lift (Airtel, India) and according to them they also received 100 + complaints of users after they upgraded to iOS 9.2.1

  Amit,

  I am also facing the same issue... its really frustrating... in my case is not at all happened to the network... do not know if everyone from apple to do anything

• Users on the network cannot use the files after upgrade to Windows 10

  When I switch to win 10 people on the network cannot use the files on my computer

  Hello

  Thanks for posting your query on the Microsoft Community.

  With the description, I understand that you have problems with network connectivity and access files on network on your Windows 7 machine. I will certainly help you to the query.

  I would be grateful if you could help me with more information to better understand the problem and a solution:

  1 is this computer connected to a network domain or home?

  2. what exactly happens when users on the network try to use/access files on this computer? Do they get an error message/code?

  In the meantime, I suggest you refer to the below mentioned thread and check if this is useful:

  http://answers.Microsoft.com/en-us/Insider/Forum/insider_wintp-insider_web/Windows-10-network-file-sharing/18fba63e-7b6c-46FE-BA23-575a634fcee8

  Hope this information is useful. Please write us back with the required information for assistance, we will be happy to help you.

• can not detect the iphone after upgrading 12.5.1.21

  Set to update to the latest version of itunes (12.5.1.21) and now itunes does not detect my iphone.  tried to remove the lockdown folder. tried to restart all devices.

  Windows 10 with all updates installed. Someone at - it suggestions?

  If your iOS device does not appear in iTunes, try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  To step 3 above, open the Device Manager. Expand one of the articles that are listed.

  • USB Bus controllers
  • Imaging devices
  • Portable devices
  • Other devices

  Plug in the appliance. You should hear the telltale Windows sound device connection and a Division must acquire a new entry. This should be your device. It cannot be labelled properly at this point. If you do not hear a suspicious noise cable damaged.

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support Apple version of the above opinion.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates. 64-bit users might also try the alternate build Download iTunes for Windows (64-bit-for older video cards) , which is sometimes a useful workaround.

  Or try to go back to the last version of iTunes that has worked for you. See the programs installation of iTunes to download links. If you're back 12.5.1.21 to 12.4.3.1 or 12.4.2.4, for example, then you will also need to restore the database of the library using the method described in the empty/corrupted after upgrade/crash iTunes library. The tip makes suggestions to reintroduce recent purchases, so at worst, you lose a few meters or a newly created playlist.

  TT2