SPA3102 Configuration Simple

Similar Questions

• Tecra R10 - 10W PCI configuration simple controller-Wireless manager

  I have a Toshiba Tecra R10 - 10W. I installed win7 and in Device Manager, it cannot find the driver for "PCI configuration simple controller.

  Also when I try to use the Wireless Manager Toshiba for 3 g it is said that the radio is off, but in reality the trigger and the WiFi works.

  Perhaps these two errors are connected.

  Thank you

  Hello

  I think you need the driver Intel AMT controller (Intel Active Management Technology).

  As far as I know, you can download this driver Toshiba driver European page or the page of the Intel driver.
  In this case, you will need to search for Intel Management Engine Interface driver

  > Also when I try to use the Wireless Manager Toshiba for 3 g it is said that the radio is off, but in reality the trigger and the WiFi works.

  WLan is not 3G use Fn + F8 to toggle the WiFi, Bluetooth and 3G.
  I think you have to press this combination of button several times to get the right setting

  Welcome them

• SPA3102 as simple FXO/SIP, no router gateway?

  Hello

  Anyone who sets up a SPA3102 as a simple gateway between the PSTN FXO line and a PBX SIP internal (asterisk or similar)?  I don't want the thing trying to act as a router; It will be on the same network segment local & subnet as the computer of PBX and just needs a trunk SIP 2-way which is actually the PSTN line.

  Would this work with just the WAN port, or maybe with two ports on the same segment & subnet connected, or who could be confused?

  Thank you!

  The f

  Hi Jeff,

  You can deploy it in Bridge mode if you do not want it acts as a router:

  Router tab > Lan Setup > Networking Service > bridge

  Kind regards

  Patrick-

• How to access SPA3102 configure page if the gateway IP address is not visible?

  Hi, in the middle of my adapter troubleshooting, we lost the address to the configuration page (empty by default gateway shows).

  Here's what I see on my online status:

  Address type: automatic private address

  IP address: 169.254.150.92

  Subnet: 255.255.0.0

  Default gateway:

  any ideas how I can access the map settings to address this problem?

  Hello

  the automatic IP address is auto-assignée IP who thought the Windows o/s.

  So you must first of ALL try to 'fix' the adapter under windows while the SPA is connected, your computer is wired for plug LAN and SPA is started... If the adapter will get the IP address of the DHCP server, you have won.

  Second, if this does not help, you can use IVR of SPA to read the addrresses WAN and LAN IP and then you must configure your card of lan of computer to "similar" IP manually - for example if the LAN IP of the SPA must read 192.168.1.1, you should set your computer 192.168.1.2, netmask 255.255.255.0 IP and access the 192.168.1.1.

  Third, if even that are not present, you can IRV SPA - 3102 allows to perform the default adapter factory reset and then follow the manual on IP addresses and connections.

• Configuring simple doesn´t work! (Wi - Fi)

  (My Palm TX is in Portuguese, I don't know about the translation)

  Prefs / adding / SSID / security (none)
  Details / connection to-Access Point (infrastructure)

  Advanced automatic DNS server IP automatic

  Connect doesn´t work.

  My Linksys WRT54G works because that I ve already connected 2 laptops!

  Maybe my PALM TX isn´t works well.

  A tip?
  TKS in advance

  Message relates to: Palm TX

  Tip number 2 above solved my problem.  I had the same situation were I could access the net on my new TX everywhere, but at home on my linksys router G band.  After trying each option and the password/key combinations without success, then I changed the mode of 'G' only 'mixed' and everything hooked up right. Thank you!

  Message relates to: Palm TX

• Problems of simple pass with Windows 8.1

  I just bought a HP ENVY TouchSmart m7-j010dx Notebook PC running Windows 8.0 about 5 days ago. I was able to configure Simple Pass, scan and add numbers and associated passwords. Then I upgraded to Windows 8.1. Now, I am unable to open SimplePass, add extra finger scans, or change the settings since the last update to Windows 8.1.

  I tried to re - install the program as a function of repair. It works by welcoming and accepting a fingerprint at the opening. When I click on the program in my Start menu as it begins to open, load databases, then disappears.

  I then uninstalled Pass Simple and re-installed after you download it again from HP at this link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-122818-1 & CC = US & DLC = in & LC = in...

  During the installation, there was a message needed me true API (x 64), which found the program installation and re-installed and then installed http://ftp.hp.com/pub/softpaq/sp63001-63500/sp63224.exe

  After you have reinstalled successfully Simple version 6.0.100.276, I rebooted my computer. However, the program is still not fully functional. I still can't open SimplePass, add extra finger scans, or change the settings. I am able to connect to Windows with a fingerprint, but he didn't ask me for analyses when I connect to different web sites.

  I'd appreciate the help. Thank you.

  See you soon,.

  Ectophile

  This message is for everyone who has problems SimplePass with Windows 8.1.

  Christopher of Jeff, executive relationship at the Head Office of Hewlett - Packard Company contacted me personally after I had tried for 5 five months get HP to fix this. I submitted to a team climbs HP Case Manager, who offered me the following options:

  # 01 Fix my computer free of charge. This shipment of the machine to them and the possability that I could lose data if they need to restore the operating system. I would be also without the computer.

  # 02 Give me a free 3 year warranty extension on my current computer which includes a home service on some components, but not the motherboard and cover against accidental damage.

  # 03 Give me an equivalent model new HP laptop computer with extended warranty of 3 years including in-home services and coverage against accidental damage. For this, restoring them my old computer AFTER transfer of programs and data to the new machine files. It was suggested that I go to the HP online store and browse the available templates. They also indicated that they would be willing to make minor improvements if my exact specifications are no longer available.

  I am sure that these same choices could and should be available to ANYONE who also had these same problems very frustrating and annoying. After all, we all paid an additional amount for software and SimplePass fingerprint scanning equipment and are entitled to expect that it works with all versions of Windows 8.

  If, as I have, you have also made several attempts to get this problem resolved by HP, Best Buy, Microsoft, or any other third party, without success, try to contact Jeff Christopher directly at [email protected].

  I hope that this could finally solve this problem, and everyone gets the same fair and equal treatment that was offered to me.

  I must also congratulate HP to finally take a step upward, appropriating and goes the extra mile to resolve this problem. Accordingly, my view of HP and my loyalty to them, increased considerably.

  See you soon,.

  Joel

• L8X51AV: My HP Envy 17 t-n100 will support ssd sata 3 m2?

  The product manual has this to say on HDD and ssd support for a multitude of different models of envy:

  The manual - http://h10032.www1.hp.com/ctg/Manual/c04696907

  Supports 6.35 cm (2.5 in) hard drives SATA 9.5 mm (.37 inches) and 7.0 mm (.28 in.) thick

  Accelerometer / HDD protection support

  Support for the 2nd HARD drive

  Support for disk HARD SATA (Port1)

  Support for SSD m.2 (support the storage function, assuming that the SSD > = 128 G, Port0)

  HARD drive configurations simple

  Support for the conƭgurations of following hard drive & #29;

  • 2 TB 5400 RPM, 9.5 mm
  • 1 TB 5400 RPM, 9.5 mm
  • 750 GB, 5400 RPM, 9.5 mm conƭgurations SSHD
  • 1 TB 5400 RPM 9.5 - mm w/8 GB NAND SSHD

  Conƭgurations of double storage & #29;

  • 1 TO + 256 GB SSD SATA M2 (TLC)
  • 4 TB: 2 to (5400 RPM) x 2

  Conƭgurations SSD & #29; (available for i7 + GTX PCA)

  • 512 GB M2 (TLC) SATA SSD
  • M2 OF 128 GB SATA-3 (TLC)
  • Value of SATA - 3 GB for the M2 (TLC) 128

  Assistant HP support said that I have the laptop next:

  Product no.: M9X68AV

  Model No.: n000 CTO

  While the my note compartment I have this model:

  Product no.: L8X51AV

  Model No.: 17 t-n100

  The record is not clear what storage configuration applies to which model.  Here is the configuration of my laptop:

  10 64 Windows Home
  6th generation Intel Core i7-6700HQ CPU Quad Core + NVIDIA GeForce GTX 950 M 4 GB discrete graphics
  16 GB MEMORY DDR3 - DIMM 2
  17.3 inch diagonal touch-screen (1920 x 1080) Full HD WLED backlight IPS
  5400 RPM 1 TB hard drive
  Test of office software
  Security software testing
  Battery Lithium-ion 6 cells 62WHr
  DVD SuperMulti burner
  Backlit keyboard
  Webcam HP TrueVision HD with dual digital Microphone, fingerprint reader
  Intel 802.11ac WLAN and Bluetooth (r) [2 x 2]

  I recently ordered this ssd sata m2 of amazon, but I'm not sure its compatible with my system - http://www.amazon.com/gp/product/B00TGIW1XG?psc=1 & redirect = true & ref_ = oh_aui_detailpage_o00_s00.

  Its a Samsung 850 500 GB M.2 3.5 inch SSD Form Factor 80nm.  Can I use in a configuration to double for my laptop with the current 5400 RPM 1 TB HARD drive already in the system?  Or do I have to use one or the other?  Or can I select a smaller SSD storage for a double configuration?  I have to talk to a technician and he said my system does not support a 128 GB ssd and it did not indicate if it is a double or a single disk configuration.  In my view, it is difficult to imaging a new desire to 2015 with an i7 Quad Core skylake 6700HQ processor supports only a meagre 128 GB SSD.  Any ideas on what my system can support?

  I can verify that it works very well. I had HP technology insist that I could use only one hard disk and a maximum capacity of 128 GB. The technicians don't know squat. I use now a configuration double with the operating system and my programs on my 850 m2 sata evo III 500 GB SSD and my data (videos, music and photos) files on the preinstalled 5400 RPM 1 TB HARD drive.

• Installation of Fios extreme airport

  I have Verizon Fios now.  I saw that the use of the AirPort Extreme with the Fios router, it must be set in Bridge mode.  But then I read do not put it in Bridge mode.  Does anyone know the correct configuration? Thank you

  To each question, there is a range of opinions...

  I think that fill the AE is fine... You will find that some features are lost... and much earned.

  It is always a... balancing act for a configuration simple and intuitive... bridge of EI.

  FIOS may be impossible to bridge, and the best you can achieve puts EI in DMZ... which isn't easy to do and leaves the FIOS still works as a router without the public IP address... order to you will lose lose in this configuration.

• Blue screen of death during recovery

  Apparently, the latest updates from MS caused problems and I had the blue screen of death during the start several times on my Pavilion p6610f desktop computer. I try a system recovery and got the screen died shortly after the recovery began. Now it does not start or even turn on a screen.  Any help would be appreciated.

  Well, this is my fourth attempt at this announcement, I hope it will work this time.  Below are my answers to your questions.

  Hello jp-3,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post about how you are not able to boot your Windows computer after attempting a recovery, and I'd be happy to help you! To start, I have to ask you a few questions:

  Mech Hi and thanks for your help.

  • What is product and model number from your desktop?

  It is a Pavilion p6610f desktop PC

  • What version of Windows you have installed on your computer?

  I was running 7 Home Pro

  • Has your computer finished all his important updates from Windows?

  The updates had been installed, which was when I started to have problems

  • Have you updated your drivers from HP the HP SupportWizard?

  I didn't have a chance to update anything after you restart MS. updates He immediately started crashing. I restarted three times and got a truncated blue screen every time, that's why I tried the recovery.

  • What is a current or recent problem?

  He started just after the latest version of Windows update.

  • You are able to get an image from another monitor?

  In general, I run two monitors (bothHP) via USB converter j5create JUA310, which I unplugged in case of conflict. It crashed with two configuration simple and double monitor. When I was running food, I had only the primary monitor upward.

  In the meantime, I recommend that you follow this document on screen is blank after you start the computer. This should help with the display on your screen when you start first to the top of your computer.

  I unplugged everything - HP Color laser printer duplicator Kensington USB port and USB mouse Logitech wireless (wired mice HATE!). Had previously removed just in case USB Sandisk flash drive. The computer started, monitor went up, and I received a message "windows recovered from an unexpected shutdown - check online solutions. Did respond to the message again. Did not try a BIOS update.

   

  Thanks for your help!

  Please re-post with the results of your troubleshooting, as well as the information requested above. I look forward to your reply!

  Concerning

  MechPilot
  I work on behalf of HP

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• E1700 - no internet needed. Config tips please?

  Hi all

  I just took an E1700, but I do not wish to use it to access or provide internet.

  I want to use it for DJing. I have 2 x controllers, music (Denon SC2900) I want to connect through the router, while creating a wifi network that will allow me to connect the controller via an app on my iPad.

  Please could someone advise me on the basic configuration, simple? I have nothing else to connectivity between the two controllers of music and the iPad - and I repeat, there is no external internet access. It's basically just going to be a switch with wifi.

  Any help would be greatly appreciated.

  See you soon

  Chris

  Nothing special to do.

  I recommend defining "Wireless-N-Only", automatic channel width and wireless "WPA2 Personal" for best performance wireless security wireless.

• Help Setup WPA2-Enterprise on WRT-160Nv2

  I am trying to configure an Access Point configuration simple (without function of linksys router), but need WPA2-Enterprise.

  I connected a single ethernet cable to a LAN port and configured RIP, DHCP and WI - FI.

  Everything works perfectly if I use WPA2, but if I set to WPA2-Enterprise, I can not connect.  Not even an IP address, I get a zero conf (169.254.x.x) in my test client.

  My radius server receives any packet of the WRT160N at specified port (1812).  Is this a known bug or I do something wrong?

  I've already upgraded to version 2.0.02 Firmware 15 no result in this case.

  Thanks for your help...

  I can't explain what happened here, but all of a sudden my system started working...

  While accidentally navigating at night, my iPhone connected to the WRT160N, instead of my old AP and finally their has requested a user/password and after the entry, I received the new certificate of AP.

  Maybe the problem was indeed with the iPhone.  He might have somehow cached the previous connection test configuration (WPA2. no company), for example.  I'm not sure, but happy that she now works...

  Thanks for all help...

• W2000 PPTP in the path through the PIX PIX

  Inside of a configured simple PIX I have a w2000 customer VPN with PPTP. The client cannot talk to one another otside PIX configured with VPDN.

  Everything works as expected if I put in a nat-Firewall NETGEAR801 instead of PIX siple.

  See PIX config and syslog. Waths evil?

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate 2KFQnbNIdI.2KYOU encrypted password

  FAXRuw8pF2Tl7oBe encrypted passwd

  HMS host name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  access-list acl_outside allow icmp a whole

  access-list acl_outside allow accord a

  Allow Access-list acl_outside esp a whole

  pager lines 24

  opening of session

  recording of debug console

  recording of debug trap

  host of logging inside the 194.132.183.10

  interface ethernet0 10baset

  interface ethernet1 10baset

  Outside 1500 MTU

  Within 1500 MTU

  external IP 217.215.220.221 255.255.255.0

  IP address inside 194.132.183.2 255.255.255.192

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group acl_outside in interface outside

  Route outside 0.0.0.0 0.0.0.0 217.215.220.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  NSM #.

  Syslog sed:

  % 305011-6-PIX: built a dynamic TCP conversion of ide:194.132.183.10/1366 to outside:217.215.220.221/1124

  % 302013-6-PIX: built 212 for outbound TCP connection: 194.71.189.109/1723 (194.71.189.109/1723) to inside:194.132.183.10/1366 217.215.220.221/1124)

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 3 PIX-305006: failure of the regular creation of translation for the internal protocol 47 src: 194.132.183.10 outside dst: 194.71.189.109

  % 302014-6-PIX: disassembly of the TCP connection 212 for side:194.71.189.109/1723 to inside:194.132.183.10/1366 duration 0:00:10 TCP fins 788 bytes

  First off I would say don't not cut and paste your config PIX here, or at the x.x.x.x at least on your external IP address.

  The PIX does not support PPTP thru PAT (nat/global). PPTP uses the Protocol IP 47 (GRE), and the PIX cannot PAT these cause there is no TCP/UDP port number to use.

  PIX 6.3 code it will however support, but it won't be available until the beginning of next year. At the moment the only way to circumvent your situation is to define a one-to-one NAT translation for this internal host. Something like:

  > static (inside, outside) 217.215.220.222 194.132.183.10 netmask 255.255.255.255 0 0

  will do for you, providing you 217.215.220.222 routed and available. I would also change

  > acl_outside of access list allow accord a

  TO

  > acl_outside gre 194.71.189.109 allowed access list host 217.215.220.222

  It's a little safer.

• Redo log shipping after a stop pending physical

  Hallo,

  I just have a question for redo log shipping

  in a configuration simple primary/secondary 11g.

  In a shutted down an instance physical standby, redoshipping is active? Primary redo file transfer is still ongoing?

  Thanks in advance

  Hello;

  I'm not going to say no. I still SEE on the primary side before I shutdown, maintains false alarms from happening.

  Test

  Using this query

  http://www.mseberg.NET/data_guard/monitor_data_guard_transport.html

  DB_NAME HOSTNAME LOG_ARCHIVED LOG_APPLIED APPLIED_TIME LOG_GAP

  ---------- -------------- ------------ ----------- -------------- -------

  TDBGIS01B PRIMARY 5558 5557 21-OCT/12:51 1

  Stop waiting

  SQL > alter database recover managed standby database cancel;

  Database altered.

  SQL > shutdown

  ORA-01109: database is not open

  The database is dismounted.

  Journal of strength comes on primary side

  SQL > alter system switch logfile;

  Modified system.

  (3)

  Journal of before was 5558 check so make sure 5559 or higher

  Last log is

  o1_mf_1_5558_c2hn5vdf_.arc

  Wait a few minutes, no change

  Best regards

  mseberg

• Installation of Enterprise Manager 12 c - error Java?

  Installation file Actions

  Subkey = SOFTWARE\ORACLE\KEY_OUIHome1

  NLS_LANG = value
  INFO: Query return: false
  INFO: Definition of variable 'b_setNLSLANG', 'true '. The value from a block of code.
  INFO: Call the query NLSQueries11.2.0.2.0 GetOSNlsLang
  SEVERE: Abnormal program termination. An internal error has occurred. Please provide me with the following files to the Support of Oracle:

  "C:\Program Files\Oracle\Inventory\logs\installActions2013-12-25_07-36-42PM.log".
  "C:\Program Files\Oracle\Inventory\logs\oraInstall2013-12-25_07-36-42PM.err".
  "C:\Program Files\Oracle\Inventory\logs\oraInstall2013-12-25_07-36-42PM.out".

  The output file.

  DLL to load is C:\Users\Jeff\AppData\Local\Temp\OraInstall2013-12-25_07-36-42PM\Win64RunProcesses.dll

  C:\Users\Jeff\AppData\Local\Temp\OraInstall2013-12-25_07-36-42PM\psapi.dll load PSAPI.dll

  ERR file.

  Exception java.lang.NoClassDefFoundError: oracle/i18n/util/OraLocaleInfo took place...

  java.lang.NoClassDefFoundError: oracle/i18n/util/OraLocaleInfo

  at GetOSNlsLang.performQuery (GetOSNlsLang.java:20)

  at oracle.sysman.oii.oiis.OiisCompContext.doQuery(OiisCompContext.java:2535)

  at Components.oracle.nlsrtl.rsf.ic.v11_1_0_7_0.CompInstallPhase1.doCodeP1Block1 (unknown Source)

  at Components.oracle.nlsrtl.rsf.ic.v11_1_0_7_0.CompInstallPhase1.stateChangeActions (unknown Source)

  at Components.oracle.nlsrtl.rsf.ic.v11_1_0_7_0.CompActions.stateChangeActions (unknown Source)

  to oracle.sysman.oii.oiif.oiifw.OiifwInstallPhaseWCCE$ OiifwComponentIP1WCCE.performStateChangeActions (OiifwInstallPhaseWCCE.java:2505)

  to oracle.sysman.oii.oiif.oiifw.OiifwInstallPhaseWCCE$ OiifwComponentInstallPhaseWCCE.doOperation (OiifwInstallPhaseWCCE.java:1375)

  to oracle.sysman.oii.oiif.oiifw.OiifwInstallPhaseWCCE$ OiifwComponentIP1WCCE.doOperation (OiifwInstallPhaseWCCE.java:1949)

  at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:171)

  at oracle.sysman.oii.oiif.oiifw.OiifwInstallPhaseWCCE.doOperation(OiifwInstallPhaseWCCE.java:874)

  at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:171)

  at oracle.sysman.oii.oiif.oiifw.OiifwActionsPhaseWCDE.doOperation(OiifwActionsPhaseWCDE.java:619)

  at oracle.sysman.oii.oiif.oiifb.OiifbLinearIterator.iterate(OiifbLinearIterator.java:147)

  to oracle.sysman.oii.oiic.OiicInstallSession$ OiicSelCompsInstall.doOperation (OiicInstallSession.java:4289)

  at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:171)

  at oracle.sysman.oii.oiic.OiicPullSession.doOperation(OiicPullSession.java:1356)

  at oracle.sysman.oii.oiic.OiicSessionWrapper.doOperation(OiicSessionWrapper.java:292)

  at oracle.sysman.oii.oiic.OiicInstaller.run(OiicInstaller.java:578)

  at oracle.sysman.oii.oiic.OiicInstaller.runInstaller(OiicInstaller.java:968)

  at oracle.sysman.oii.oiic.OiicInstaller.main(OiicInstaller.java:905)

  Caused by: java.lang.ClassNotFoundException: oracle.i18n.util.OraLocaleInfo

  at oracle.sysman.oii.oiix.OiixJarClassLoader.loadClass(OiixJarClassLoader.java:674)

  at oracle.sysman.oii.oiix.OiixJarClassLoader.loadClass(OiixJarClassLoader.java:731)

  ... more than 20

  Please see section 8.4.1 Installationavecuneracine Configuration Simple (step 12 enter installation details) in the following doc:

  Installation of a system of Enterprise Manager

  Kind regards

  -Loc