Stop 0x0000007e on an XP

Similar Questions

• 6910p: STOP: 0x0000007e error

  I'm trying to install XP on an old portable 6910p.  Immediately after loading drivers, I get the dreaded BSOD:

  STOP: 0X0000007E (0XC0000005, 0XF74BE0BF, 0XF78DA208, 0XF78D9F08)

  PCI.sys - address F748E0BF base at F7487000, DateStamp 3b75d1ac

  Here are all the steps I took:

  different memory

  different (standard and SSD) HARD drive

  reset the bios

  bios update

  disabled the additional devices in the bios (bluetooth, wlan, etc.)

  charge sata drivers

  replace windows media

  Started from the external cd drive

  I don't see anything else to try... I'm out of ideas

  HP Compaq 6910p

  s/n: CND74525Z5

  It not.

  He had.

• "A problem has been detected and Windows has shut down to prevent damage to your computer"... * STOP: 0x0000007e (0x805c49b8, 0xf7a172b4, 0 x 80000003, 0xf7a16fb0)... blue screen

  Hello!

  For the life of me I can't figure out how to get my machine to boot successfully. Nothing changes when I choose Safe Mode, last known good Configuration, enable VGA Mode, booting, Directory Services Restore Mode or Debug Mode logging.

  It's very stressful, because I'm right smack dab in the Middle a semester at the College. I have most of what I currently need access to supported illuminates... but not quite all :( It is also very reassuring to be able to take care of the school of work away from the library of the University. Yesterday, my computer was working fine... I think that Windows has completed an update, if I can't remember now. As I woke up this morning, I was not able to boot all the way to Windows only once.

  My laptop is a HP Pavilion dv6000 running XP Media Center, and I have not installed new hardware since I bought the machine about 3 years ago.

  Here are more details, where they can help in the diagnosis of my problem:

  • ID of the system board: 30BB
  • Type of processor: Genuine Intel(r) CPU T2250
  • Processor speed: 1730 MHz
  • Total memory: 1024 MB
  • Video memory up to: 128 MB
  • BIOS version: F.06

  Here's the entire message to the blue screen:
  - - - - - - - - - - - - - - - - - - - -
  A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0X805C49B8, 0XF7A172B4, 0 X 80000003, 0XF7A16FB0)
  - - - - - - - - - - - - - - - - - - - -

  I also learned to a blue screen that says something about "PAGE_FAULT_IN_NONPAGED_AREA". I think that this happens when I try to start safe mode.

  Also, I never did much with computer problems beyond what could be repaired with the restoration of the system... so not being is not able to boot at all me has to stop. Please, I beg you! Help me?!

  With great appreciation for your time,.
  Damaya

  Quick suggestion

  Some HP partition the hard drive. have you tried to type F11 or F12 during startup (before that he go to the option mode start screen)? It might take you for a HP recovery program in that partition (because windows don't be loading not to use that recovery)
  Good luck

• Stop: 0x0000007e (0xc000001d, 0 x 80537008, 0xba4c33b8, 0xba4c30b4)

  I received the following during startup error message:

  A problem has been detected and windows has been closed seeded to avoid damage to your computer

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again, follow these steps:

  Make sure you have enough disk space...

  Check with the hardware vendor for updates to the BIOS...

  Technical information:

  STOP: 0X0000007E (0XC000001D, 0 X 80537008, 0XBA4C33B8, 0XBA4C30B4)

  Help, please!

  Uninstall KB977165

  I deleted KB977165 as follows.

  Started by using BartsPECD or use your recovery CD

  Change directory to c:\windows\$ntuninstallkb977165$\spuninst

  Copy the file spuninst.txt spuninst.cmd

  Run the file spuninst.cmd

  He will be back on the change.

  I've been very successful with that.

• Im trying to install windows XP on a hard disk nine and im getting a blue screen Stop: 0x0000007E

  Stop: 0x0000007E (0xC0000005, 0xF748E0bF, 0Fx78DAZ08, 0xF78D9F08)
  PCI.sys - address f748E0BF base at F7487000, Datestamp 3b7d855c

  Hi martydh,

  Thanks for posting. This message is often caused by incompatible hardware. Please remove and unnecessary for PCI cards, cards AGP/PCI-E, external devices and use only the minimum amount of RAM you can. After doing this please try reinstalling the operating system. Also check with the manufacturer of your motherboard OEM or PC to see if it's updated controller drivers, that you can use.

  I hope this helps! Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  How to fix blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced

• Stop: 0x0000007e (0xf77a52b2, 0xf7c84490, 0xc0000065, 0xf7c84190) fltmgr.sys - address f77a52b2 base at f778dooo, datestamp 480251da

  This error on a blue screen when I boot Windows xp pro. Welcome suggestions please.

  Hi John,.

  You can check the following thread link and advice given by Matthew_Ha, moderator of the Forum.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/fltmgrsys-BSOD-when-repairing-Windows-XP/012f5f78-ABA7-4e4e-B41D-c877d343f15f

  You can read the following article and check.

  How to solve an error "Stop 0x0000007E (SYSTEM_THREAD_EXCEPTION_NOT_HANDLED) code error" in Windows XP

• Impossible to reinstall Windows XP error: BSOD STOP: 0X0000007E (0XC0000005, 0XF78DA208, OXF78D9F08)

  Original title: BSOD

  tried to reinstall windows xp bsod STOP: 0X0000007E, (0XC0000005, 0XF78DA208, OXF78D9F08 * pci.sys_address more numbers to several numbers and a date stamp.)

  Hello

  1. How are you trying to install?

  2 do you use a full version Windows Setup disc or the recovery disk?

  3. at what stage of installation you get the error message?

  I suggest you try the steps from the link below and check if it helps.

  http://support.Microsoft.com/kb/330182

  Additional information:

  How to fix a computer that does not start: http://windows.microsoft.com/en-US/windows-xp/help/setup/how-to-fix-computer-that-will-not-start

  Hope this information is useful.

• blue screen STOP: 0x0000007E

  I use XP and this morning I received the following error message

  STOP: 0X0000007E (0XC0000005, 0X89B8E988, 0XF78DABE8, 0XF78DA8E4)

  I can't restart in safe mode and the research revealed no information about this error. It started when I tried to deactivate restore system., how to fix this?

  Hello

  1 did you changes to the computer before the show?

  You can try the troubleshooting provided in the links below steps to fix the problem.

  How to troubleshoot a Stop error 0x0000007E in Windows XP

  http://support.Microsoft.com/kb/330182

  Error after you upgrade a computer that uses one processor other than a processor of Intel for Windows XP Service Pack 2 or Service Pack 3 for Windows XP: "STOP: 0x0000007E"

  http://support.Microsoft.com/kb/953356

• Blue screen - Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)

  Original title: need help with Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)

  Can someone telll me how fix an error that says "Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)"?

  If the message under your STOP error message indicates this (probably not):

  WUSB54GCx86.sys - address 92 D 89498 base at 92D7c000, Datestamp 45c04cc9

  So the response from Microsoft support technician can help you.

  If the message under your STOP error message indicates this (most likely):

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

  So the response from Microsoft support technician is not worth reading.

  If this is the case and you have an AMD processor, you must look at this article:

  http://support.Microsoft.com/kb/953356

  If we knew what was your system brand and model and a few other details when you made your initial post or someone have asked a few questions, you would have probably solved this problem in one or two cycles of message, but now 6 days.

  It is the shame that the MS Answers forum does not ask for any kind of information system when a new question is asked and we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Thank you MS Answers, allowing the resolution of simple problems as frustrating and a lot of time as possible.

• Message Stop 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0) when to stop or restart the computer.

  Original title: message of stop 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0).

  Hello. I am running windows xp sp3 (sp2 initially update) when I try to stop or restart my computer I get a blue screen that says stop: 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0)

  Kbdclass.sys-
  address F880E9AC
  F880E000 base
  datestamp 48025372
  Help, please.

  Hi monicashannon,

  1. are you experiencing this problem after installing Service Pack 3 or you have made other changes to your computer?

  2. what processor you have on your computer?

  You can follow this link & check if the problem persists:

  Error after you upgrade a computer that uses one processor other than a processor of Intel for Windows XP Service Pack 2 or Service Pack 3 for Windows XP: "STOP: 0x0000007E"

  Reference: How to troubleshoot a Stop error 0x0000007E in Windows XP?

  Hope the helps of information.

• Error while installing windows Xp on my E Aspire 13 ES1-311-C4VK. Error is STOP: 0x0000007E.urgent pls help

  I tried so many times to install windows xp on my Aspire E 13 ES1 boot cd - 311 - C4VK.Xp first, then load something. After that, it shows the error:

  STOP: 0X0000007E (0XC0000005, 0XF73B9D66, 0XF78D9EA0, 0XF78D9BC)

  ACPI.sys - address F73B9D66 base at F73AE000, DateStamp 480252 b 1.

  I need urgent help.

  And another thing, I want that it is not possible to change the sata ACHI to ide mode. Isn't it possible to change?

  Why windows XP?

  It is not longer supported by Microsoft and other SOFTWARE, and it is the best OS to have viruses, rootkits and other infections.

  you will be also problems of drivers/hardware as acpi.sys

  If you need windows XP for some old software, try to use a virtual machine or buy a second hand laptop.

• Why do I get a blue screen with the error STOP: 0x0000007E every time I turn on my computer?

  Error message: STOP: 0x0000007E (0xc0000005, 0xB42E09AC, 0xBA4E39B4, 0xBA4E36B0)

  Here is the text of the BSOD:

  STOP: 0x0000007E (0xC0000005, 0xB0B9B9AC, 0xBA4DF8AC, 0xBA4DFSA8)

  Kbdclass.sys - address BOB9B9AC base at B0B9B000, DateStamp 48025372

  Some of the Stop line numbers change but their pretty much the same content. There is no C:\Windows\Memory.Dmp file on this computer.  Sorry it takes so long

  The Kbdclass.sys driver that is referenced is the keyboard class driver that is a component of Windows.

  It is possible that the accident might actually be due to a third-party keyboard driver.

  If you have installed a third party (for example. Keyboard Logitech driver) can update you or, if necessary, uninstall the third-party keyboard driver and see if the error resolves?

  Article on Microsoft:

  http://support.Microsoft.com/kb/313050

  In accordance with article Logitech Mouseware software can also cause the error.

• Blue screen error STOP: 0x0000007E (0xC0000005, 0x8Ac18874, 0xF792A468, 0xF792A164)

  Original title: blue, impossible to restart screen

  System: Dell Dimension 3000, Windows XP Home - SP3.

  Problem: I recently installed the new memory (now has 2G), check that the memory has been recognized and work.  Computer worked fine for several hours, with a noticiable improvement.  Then received warning from McAfee "A Trojan had been identified" and the computer had to be stopped to fix.  Not sure if this was related to the new memory, but the moment was just a few hours apart.  When I tried to restart the computer - I got a blue screen of death with the following technical information: * STOP: 0x0000007E (0xC0000005, 0x8Ac18874, 0xF792A468, 0xF792A164).  I can't start the computer in safe, except the Mode modes safe mode with command prompt and to my level of skills making me much good.  Please notify.  Thank you.

  Hi mysticskier,.

  Follow these methods.

  Method 1: Disconnect all external devices such as printer, scanner, etc.

  Method 2: Follow the steps in the article.

  You may receive a Stop error on a blue screen when you start a Microsoft Windows Server 2003-based computer or a Microsoft Windows XP-based computer

  http://support.Microsoft.com/kb/893239

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

• Stop: 0x0000007e (0xc0000005, 0f748e0bf, 0xf78da208, 0xf78d9f08)

  Original title: pci.sys - address f748e0bf

  Reloading windows xp and iam getting a blue screen. Technical information: * stop: 0x0000007e (0xc0000005, 0f748e0bf, 0xf78da208, 0xf78d9f08)

  PCI.sys - address f748e0bf base at f7487000, datestamp 3b7d855c

  I have a HDD 1terabyte.

  Hi matllamas,

  -Did you change on your computer before this problem?

  -What version of service pack of Windows XP you are using?

  Here are a few article which will help you to solve the problem:

  You receive a stop error 0x7E in Pci.sys

  How to troubleshoot a Stop error 0x0000007E in Windows XP

• Get the following blue screen on startup error: STOP: 0x0000007E, BAD_POOL_HEADER STOP: 0 x 00000019, IRQL_NOT_LESS_OR_EQUAL STOP 0x0000000A

  Original title: XP questions

  I am running WIndows XP Pro SP3 on a Dell Optiplex gx270s and get several error messages stop "Blue screen" intermittent and different at startup (for protect my computer). Prompt notification Windows found problems with the file system and run CHKDSK/F. I am unable to do so as I can not find my administrator password (also necessary if you plan to run from my XP installation disc). Windows Fix - It Center, running 'Folder & troubleshooting' reports icons randomly change the icons but no resolves not. I didn't notice the icons change and do not if this is related to Stop what error messages at startup, I've been doing. Running a disk check during start-up and Diagnostics IDE are not problems. It lasts for quite awhile and I've delayed just deal with it because it is not always the case. A lot of program installs / uninstalls and Microsoft Updates since its start if the system restore wouldn't do me any good. Before reinstalling the operating system, what are my options? Is there a way to reset my ' Administor password ", or better yet does not require one, (it is a personal computer for personal use only and I don't remember why a password has been assigned)?

  Here are some of the error messages:

  STOP: 0x0000007E (OxC0000005, 0x89AD8000, 0xA579CCB4, 0xA579C9BO)

  BAD_POOL_HEADER

  Technical information:

  STOP: 0 X 00000019 (0X00000020, 0X89D5FDA0, 0X89D5DC8, 0X0A050002)

  IRQL_NOT_LESS_OR_EQUAL

  STOP 0X0000000A

  (0x6750300C, 0 x 0, 00000002 00000000, 0x804FFDB6)

  Hello

  You did changes to the computer before this problem?

  The administrator password cannot be reset.

  See the following article for more information: Microsoft's strategy concerning lost or forgotten passwords

  In the following troubleshooting steps may help you resolve this problem.

  How to troubleshoot a Stop error 0x0000007E in Windows XP
  http://support.Microsoft.com/kb/330182

  FIX: Error Message When you connect a scanner or a digital camera to a computer that is running Windows Vista or Windows XP Service Pack 2: "BAD_POOL_HEADER STOP"
  http://support.Microsoft.com/kb/934177

  You receive an error message "Stop 0x0000000A" in Windows XP
  http://support.Microsoft.com/kb/314063