The host CPU is not able to run 64-bit virtual machines

Similar Questions

• Mac Pro Dual Quad 3.0 GHz (8 cores - April 2007) not able to run 64 bit comments

  Help, I should be able to do.

  See this thread, because it is a similar issue that only my machine does not all 64-bit indicating my machine does not support hardware virtualization

  http://communities.VMware.com/thread/143298?start=0 & tstart = 0

  Here is what I get:

  * "VT operation is not supported by this VM configuration. " *

  You have configured the virtual machine to use an operating system 64-bit client.  However, this host is not able to run 64-bit virtual machines or virtual computer has 64-bit support disabled.

  + For more information, see http://vmware.com/info?id=152""+ "

  Running on the latest version, but this problem has always been there in previous versions (2.0.5)

  10.5.7 (failed in earlier versions either)

  8 GB ram

  2 TB of storage

  Tried the switch recommended on the config file but nothing.

  Thank you

  You have only one physical processor that implements revision VT VMCS a 7 and another that implements revision VMCS VT 11.  These processors are not compatible for execution of VT.  One processor is family 6 model 15 stepping 7 and the other family 6 model 15 stepping 11.  Intel has released a firmware fix that resolves this problem for the processors that differ only by deepening.  You should check to see if there is an update of the firmware from Apple that contains this fix firmware.

• Cannot use 'lab1' host because the host CPU is not compatible with the judgment of the virtual machine suspend state.

  I see that this error was mailed here, but can't seem to find a position with a resolution.

  We use Lab Manager 4.0.4 and just upgraded the hosts in our laboratory.  Before updating to ESXi 4.1 ESX 4.0 u1, we cancelled all VMs in all configurations.  There is none who were suspended, they were all turned off.  We have improved vcenter 4.0 to 4.1 as well.  We moved from a dell poweredge 1950 with two quad core intel L5410 to a r610 with two quad core intel processor E5506.

  When I try to turn on some of the lab configurations (our VM models all work fine), I get this error:

  • Cannot use 'lab1' host because the host CPU is not compatible with the judgment of the virtual machine suspend state.

  I threw the State for the lab configuration (even if it was turned off and cancelled) and still get this message.  I guess the processor architecture of these chips is quite similar, and both are Intel.

  If I go into this directory of Manager of laboratory inside the data store for one of these virtual machines that does not light and add to the inventory, he turned and starts fine on my server esxi 4.1.  So how do Lab Manager to get account it's well deploy and start it?

  Hey billk.

  Although not supported completely, you can solve it by going to the SQL of Lab Manager database.  Make sure that you back up your database before you do anything like that.

  Open the table "fsdir" and corresponds to the dir_id with the id Lab Manager VM.  Once you find the relevant line, change suspend_proctype_id to null (Zero-Ctrl).  You can do this while Lab Manager is still running.

  The results can be unstable (i.e. Windows can crash if it was a drastic change of CPU), but at least you look at a hard reset.  The bat reset certainly not being able to return to the previous state.

  Also note that while Lab Manager does not include CVS, if you activated, your virtual machines still work in CVS mode.  If you have a mixture of heterogenious of hosts in a cluster for Lab Manager, you can see this question pop up a lot.  There is absolutely nothing wrong with take back the virtual machine because of the VCA, but Lab Manager thinks otherwise and prevents it.

• the sysadmin user is not able to run diagnostics through OAM?

  Hello
  When I try to run diagnostics via the OAM navigation > Site map > Diagnostics & Repair > Diagnostics > run diagnostics, the system throws an error as > > year error has occurred! Please note: you don't have sufficient privileges to perform this function. > >. Is sysadmin should have any role (RBAC) using User Management?
  
  Use of "diagnostics application" it works very well.
  
  Concerning

  PL see the first yellow box in MOS Doc 235307.1. From 12.0.6, you can only run diagnostics from the Menu of the EBS with the responsibility of "diagnoses of the Application.

  HTH
  Srini

• system is not able to run the Apple Application Support service

  I can't install itunes on windows 7 32 bit. Any suggestions on Apple Support do not work. The system is not able to run the Apple Application Support service. Any suggestiones?

  Can you post the error message you get when you try to install or launch iTunes?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Not able to run RealPlayer on the Windows XP machine, the file msvcp90.dll is missing

  Dear Sir / Madam,.

  Pls help advise the question of 'not able to run RealPlayer on Windows XP machine, file msvcp90.dll is missing'?

  Thank you!

  Hi EddieFang,

  Try to download and install real player http://www.real.com.au/.

  I hope this helps.

• not able to run micro security essentials says need to reinstall the client security micro

  not able to run the bases of microsoft security said that I need to install the microsoft security customer no idear was to conclude this

  Additional posts appear in the MSE Forum:

  http://answers.Microsoft.com/en-us/protect/Forum/protect_scanning/i-have-error-code-ox-80070715/578e0e44-99c9-4293-b75e-79e2ff1dc2b6

  http://answers.Microsoft.com/en-us/protect/Forum/protect_updating/not-able-to-uninstalll-micrisoft-security/f3bb8423-3671-453F-BB30-8b7f3e53daad

  Recommended as previously you could try to uninstall your MSE, then download and install a new copy of: File of Installation of MSE

  If it does not contact the MSE Support as previously suggested.

• MAF: Not able to run the sample project or a simple project with only one page

  Hi all

  I am trying to run examples of applications of the MAF delivered with Jdeveloper 12.1.3. I am not able to run these applications on the device in the emulator. They gets deployed successfully. However, when I try to open these applications, it hangs on the initial screen of the Oracle.

  I even tried to create a new MAF application with only a device with a page of the AMX. Tried to deploy, but still get the same result.

  No idea what could be the problem?

  Thank you

  Ajay

  Hello

  Problem has been resolved, after the re-installation of the Jdev and MAF extension.

  Understood that somehome, maf - application.xml couldn't refer to the features of the maf - feature.xml. When I created a new feature in the MAF - feature.xml, it was the adfmf - feature.xml and maf-application creation could refer to the functionality of this file.

  This seems to me an installation problem. I have therefore re-installed, now its works very well.

  Thank you

  AJ

• Error number: 0x800CCC0D, the host 'POP3' could not be found. Please make sure you entered the server name correctly in Outlook Express 6.

  Original title: "POP3" server could not be found...

  I get the following error message every time I try to use Outlook Express 6 as my default email: 'the host 'POP3' could not be found.  Please check that you have entered the server name correctly.  "Account: 'POP3', server: 'POP3', Protocol: 'POP3', Port: 110, secure (SSL): no, Socket error: 11001, error number: 0x800CCC0D".  I have a Dell Optiplex GX110 desktop computer with a processor Intel Pentium III (996 MHz, 256 MB RAM).  I already know that I have to increase the amount of RAM, but I don't think this is part of my problem.    I am connected to a local network, Verizon (Internet, cable TV and phone package). I run Microsoft Windows XP Professional (5.1.2600) 2002 with service pack 3 version.  I check frequently that my system is configured to automatically receive all updates for Windows XP more updates from Microsoft.  QUESTION: Is there a version of Microsoft in September 2011 that had something to do with POP3 servers?  Obviously it did not automatically installed in my computer.  I even checked my system twice to make sure that Microsoft was on my list of safe sites.  Please help me.  I really want to use Outlook Express 6 as my default email.

  Thank you!
  George Raynes

  Hi GeorgeRaynes,

  1. were you able to use Outlook Express 6 correctly previously?

  2 have you made any hardware changes or software on the computer before this problem?

  You can follow this link & check if the problem persists:

  Troubleshooting error messages that you receive when you try to send and receive e-mail in Outlook and Outlook Express

  Hope the helps of information.
  Please post back and we do know.

• When you run a single virtual machine on the host computer, is it ok to assign all the processors for comments

  I have a single guest Windows 7 Pro running on the host ESXi 5 U1.   It will always be in a 1-1 configuration (we needed server hardware, but with BONES desktop for purposes of licensing).  The host CPU is an E5603 (Quad - core 1.6 GHz).  I want the guest to have the maximum amount of possible processor cores, because a true multi-threaded application runs.  Because Windows 7 is limited to 4 cores, I disabled hyperthreading on the processor so that when I assigned 4 cores the VM, I get all 4, not the half because of hyperthreading.

  I am setting for claim processor between the host and the guest?  Should I only assign 3 carrots to the guest while it is still available for the host?

  With the requirement, it's guessing more than knowing what to configure. I think that with 2 Dual-Core configuration, I suggested above, you're on the save side.

  André

• The performance of the host CPU / use

  I noticed a strange behavior that one of the esx host processor cores work 100% all the time, see attached file shows running HOST - CPU 1 - 0 at 100% all the time, CPU - 1, 2 and 3

  are not, if I take a quick glance at other hosts, the use of the CPU are also almost evenly divided into 4 cores of the processor... is this normal behavior for the HOST-1?

  (cluster DRS/HA 6-host running on 3.5u2 and 2.5u3)

  Connect to the ESX host and high performance and type 'P', to sort by CPU usage.  See that heavy trucks are at the top.

  Remember that the service console runs only on CPU - 0, then it would follow that something running on the service console of that eats the host CPU, or there is a problem on this machine.

  -KjB

• I'm not able to run a Windows Azure application

  I have a very strange problem.

  I'm not able to run an application in windows azure has a WCF service and mschart inside. Here are the steps to reproduce the error:

  (1) create a new windowsazureapplication with an empty asp.net webrole
  (2) now to add a new WCfService
  (3) run to make sure it works ok

  http://i.stack.imgur.com/1g6gW.PNG

  (4) now in one pages include mschart and open page design to ensure that the webconfig is changed to use the mschart.
  (5) now try to run the project.
  I get the error message like this one:
  Enter a description of the image here

  Is this a problem with blue windows or I do something wrong?
  FYI: This isn't my first project on windows azure.

  RuchitRami

  As far as I know Toshiba doesn't support this Microsoft stuff, so I think that Microsoft is the right address for these issues.

  Have you already checked that Microsoft saying about it?

• I'm not able to run windows update. [Error number: 0 x 80244019]

  I'm not able to run windows update. I get an error: [error number: 0 x 80244019] I took and I tried all the suggestions on the support for windows Xp article because that's what I'm running [error number: 0x8DDD0010] "When you click on a link, you see the error HTTP 500 - internal server, error 0x8ddd0010 error" but none of these solutions work.  I tried the ' Fix It program this car works but askes me to install Windows XP Service pack 3 or later and .NET Framework 2.0 or later version of windows update but as you can see I can't get windows update to work if it does not really help. "  Any ideas... Help, please!

  What XP SP level are you at?

  For your error: http://support.microsoft.com/kb/883820

  But that will not help you if you are not at the level of SP3.

  You must be at Service Pack 3 level before you can use Windows updates.

  To determine which service pack is currently installed on your computer, follow these steps:

  1. Click Startand then click run.
  2. Copy and paste, or type the following command, and then click OK:

  winver

  A dialog box displays the version of Windows and the service pack that is currently installed on your computer.

  See also: http://support.microsoft.com/kb/2497281
  You may be unable to access the site Web Windows Update in Windows XP, Windows 2000 or Windows Server 2003

  If you haven't already done so, you will need to install the SP2 and SP3 (SP1 note no longer exists).

  How to obtain the latest Windows XP service pack
  http://support.Microsoft.com/kb/322389

  SP2 - http://www.microsoft.com/en-us/download/details.aspx?id=28
  (for single PCs too)

  For Windows XP Service Pack 2 installation procedure
  http://support.Microsoft.com/kb/875364

  Steps to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717

  It is stated in "How to obtain the latest service pack XP" is.

  If you have problems obtaining the service pack from Windows Update, you can download the package of standalone update from the Download Center. This page will say that this installation package is intended for it professionals and developers. However, you can download this file safely. The following file is available for download from the Microsoft Download Center:

  Download the Windows XP Service Pack 3 package now

• Whenever I open my Windows Mail, get an error 'the host 'Pop3' is not found.

  Everytime I open my Windows Mail I get the following message will appear.

  The host 'Pop3' could not be found, check that you have entered the server name correctly.
  Account: 'Pop3' (1) Pop3 Protocol Pop3 110, secure (SSL) server no socket error 1101, wrong number Ox800cccod,
  I am able to use windows Mail without problems apart from this guard popping up which is very annoying
  
  I have no idea how to do to stop what is happening
  
  I'll be very grateful if someone can help me with this problem
  
  Thank you
  
  Tony
  * original title - how to stop can't find the waiter to come to the top *.

  Go to tools | Options and uncheck the option to send and receive at startup.  See if that takes care of the problem.  He might try to receive before its ready.  Also check your settings under Tools | Accounts and checking accounts are configured correctly.  You can also try compacting and repairing the database to clear up all the weird questions (see www.oehelp.com/WMUtil/) and look out for interference of program part 3 (see www.oehelp.com/OETips.aspx#3).

  Steve

• Wi - Fi connection error: the hosted network could not be started.

  Original title: need help Urgent

  I get this error message. I'm not able to start the wifi sharing in my lenovo ideacentre desktop. I'm not able to see the microsoft wifi adapater everywhere in my office, even in the Device Manager and the adapter option Add.

  C:\Windows\System32>netsh wlan start hostednetwork
  The hosted network could not be started.
  The group or resource is not in the correct state to perform the requested operation.

  Hi Siddha,

  The question you posted would be better suited in the TechNet Forums; We recommend that you post your question in the TechNet Forums to get help:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro