The Pix501 to VPN3030 disorders

Similar Questions

• To access the PIX501 via HTTP

  I'm a little confused right now. I'm trying to config PIX501 accessmy & PDM via HTTP, but it's not working. Please see my config below. Thank you!

  6.3 (3) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password >

  passwd >

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  pager lines 24

  debug logging in buffered memory

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 10.29.18.1 255.255.255.248

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 10.29.18.0 255.255.255.248 inside

  PDM 100 debug logging

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group outside-outside interface

  Route inside 10.128.40.0 255.255.255.240 10.29.18.2 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 10.29.18.0 255.255.255.248 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  Terminal width 80

  Hello

  Your PIX config has the following:

  Enable http server

  http 10.29.18.0 255.255.255.248 inside

  If you try to access the market SHARE of 10.128.40.0 255.255.255.240 then you must add this to your config as file:

  http 10.128.40.0 255.255.255.240 inside

  Your routing looks correct on the PIX, its delivery to 10.128.40.0 255.255.255.240 by what seems to be your SOHO router, so you should be able to ping the inside interface of the PIX

  If not add "icmp allow no matter what Interior"

  Rgds

  Paddy

• the pix501 vpn Installer

  I have a pix 501 6.3 (5), with these features of license:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: 10

  My questions are, how VPNs can I, vpn site-to-site and remote user or? Finally, how to create the host remote vpn? Do this through the line of cmd or web-based? Or did someone knows a link or a guide explaining configuring vpn on this model. If more info is needed let me know. Thanks in advance.

  You can use L2TP over IPSEC to a windows client. Attached is a link to a doc to configure L2TP over IPSEC between a pix firewall and a w2k pc. It should apply to XP as well.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800942ad.shtml

  HTH

  Jon

• Hello world!! the rookie again! disorders of "renditions" ipad iphone and some doubts please!

  Hello world!!! several questions please:

  1. I neeed update for the client, an application for dps ipad real and alive, with a new iphone and ipad version update! I made a standard size of 768 x 1024 ipad and match the iphone 5 and 6, but not the iphone 6 more!

  Which is the best size 'generic or standard' to fit the iphone 6 more? possible or I need to build several formats and different sizes to match the iphones 4, 5, 6, and 6 more?

  2. do I need to work the new provisions of alternatives for all items? I mean I now the 768 x 1024 ipad standard layout, and then updated to itunes connect download again once a new .ipa file that includes all the new iphone alternates 6 plus size 1136 x 640 and 1024 x 768 ipad?

  3. the best method recommended is the liquid layout?

  Tank much at all and sorry for my silly questions im just a rookie in this world of dps great app!

  Hi Maurice.

  (1) you don't need to create content for the 6 +. See my next response below.

  (2) you need to create new items for all screen sizes different iOS device you want to target. Other layouts in InDesign can help with this, but you still need to manually adjust everything to get different sizes. It's really not worth it to create a new layout for each different iPhone. It is better to make a set of content 1136 x 640 for the iPhone 5 and later devices and a set of content to 480 x 320 for the iPhone 4 and earlier versions of devices. These numbers are taken from https://helpx.adobe.com/digital-publishing-suite/help/create-folio-renditions.html.

  3) there is a single method, but if it is the best depends on how you want to design your content for phones. In some cases, it is easier to just start with new documents for renderings of phone from the page layout is usually much simpler.

  Neil

• Activating/Deactivating the table of contents disorders...

  Hello, I have a sample project 1 simple slide with a single button.  The next action is attached to the button, but I do not get the result I want.  Why won't it make my OCD go out?

  Thanks for any help!

  

  Problem solved.   Should be decorative, not separate.

  

• PIX501 customer VPN - cannot access inside the network with VPN Session

  What follows is based on the config on the attached link:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

  PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

  We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

  Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

  We have the same problem with the customer 4.0.3(c)

  Thanks in advance for any help!

  =======================================

  AKCPIX00 # sh run

  : Saved

  :

  6.2 (3) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname AKCPIX00

  domain.com domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  fixup protocol sip udp 5060

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  external IP address #. #. #. # 255.255.240.0

  IP address inside 192.168.1.5 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool akcpool 10.0.0.1 - 10.0.0.10

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address akcpool pool akcgroup

  vpngroup dns 192.168.1.10 Server akcgroup

  vpngroup akcgroup by default-domain domain.com

  vpngroup split tunnel 101 akcgroup

  vpngroup idle 1800 akcgroup-time

  vpngroup password akcgroup *.

  vpngroup idle 1800 akc-time

  Telnet timeout 5

  SSH #. #. #. # 255.255.255.255 outside

  SSH timeout 15

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd dns 192.168.1.10

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  AKCPIX00 #.

  Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

  mymap outside crypto map interface

  ISAKMP allows outside

  Enter these two commands should be enough to reset the ipsec and isakmp.

• I have 2 Gmail accounts that I use Thunderbird to work with. Suddenly, one of the accounts has stopped working (password requests).

  For a year I used without problem Thunderbird to work with two of my Gmail accounts without problems.
  I had been on a long trip for the last 2 weeks had not begun to Thunderbird. When I did it for the first time this morning, I couldn't work or another account with it.

  Reset, return all settings solved the problem for ONE of my accounts (the main!), but the other continues to refuse to work.
  Yes, I have IMAP and less secure device permissions enabled in the Gmail settings. I changed my passwords and their update on all ends and again, my main account works, but the other refuses to accept passwords, even though I know they are correct.

  I still get the "cannot connect to server imap.gmail.com ." Message and I am prompted for my password.

  No luck.

  Could someone help me novel?

  Thank you very much,

  Zea

  After digging around a few others, I finally managed to find the google site:

  https://support.Google.com/accounts/answer/6009563

  There is a link on the bottom, saying: "allow access". Click on this one, 'continue' and directly there after prompt to synchronize Thunderbird. That solved the problem.

  Synchronize Thunderbird now until my two accounts again.

  Thanks for all the help and all the world looking in there, I hope this helps the other 3 who clicked on they have the same problem.

  PS: In your web browser, you must be connected to the Google account with disorders!

• Toshiba with vista touchpad mouse stopped working after the long sleep.

  I left my Toshiba laptop with Vista only for a few hours and when I came back I had a lot of difficult to resume. When he did power to the top of the screen is fixed to the external monitor, and touchpad mouse will not work.  I did a system restore to several days ago, but it did not help.  I also installed service pack 1 and 2, hoping that would be useful, but it did not.  What should I do to get the touchpad mouse works again? I have the back of the screen, but not the mouse.

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• Why my computer keep stop inadvertently with this message: address a problem with the NVIDIA Graphics Driver__NVIDIA graphics driver has stopped working properly. ? __

  Recently my computer (laptop) was stopped when I put the command "sleep".  It displays a message about my NVIDIA Graphics Driver does not. I have check the driver to use and it shows like th emost current and NVIDIA hardware works correctly... who is not lying.

  A recent Microsoft update would be the cause of this problem suddenly?

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• When the pc is a sleep he doesn't.

  I have Windows Vista I my pc to go to sleep when I close my lid on my laptop when I will use again the internet doesn't come baqck I have to reboot to get my internet back, can help someonr you please.

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• Computer lock up after the active screen saver. __

  The problem: after the screensaver kicks in if I stop I'm usually back in the log on screen, however, if the computer starts to slow down, sleep, CV, I get a black screen and I can hear the computer still active in the background and I can hot key to open applications, but all I see is a black screen. Sometimes I see the mouse on the black screen. My resolution is to turn it off and turn it back on.

  Any ideas, I played with the Device Manager and deleted a few? the elements and rebooted to see if any device driver was causing the problem. I played around with the screen saver and power management and tried different settings and nothing works.

  See you soon.

  http://help.ISU.edu/index.php?action=FAQ&CATID=79&docid=396

  FAQ - How to remove the Windows Screen Saver password

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• Closing lid on the use of the active battery put into hibernation. Closing lid that plugged while active put into hibernation but the computer wakes up right after hibernation mode ends.

  I put my power settings to have the laptop Hibernate when I close the lid.  On battery it hipernates and the computer turns off.  When it is plugged in it hibernates and turns off, but after a few seconds, it wakes us up.  I want it hibernates and shuts off when I close the lid.  Am I missing a command/selection?

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• Can not keep the computer in mode 'sleep '.

  computer will not sleep

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• Cannot get computer to exit the mode "sleep"...

  Earlier this morning, my computer for 15 hours to exit the mode hibernation; some very useful posters expressed the view that it could be a battery problem, but thatprobably was not the case.

  Now, he's not out of "sleep mode".

  Should I disable one or both of these modes, or do a "hard" reset (I've heard the term, but I don't know how it's done), or try something else.

  This is a laptop HP 3 year with Vista & IE 8.

  Thank you!

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info on sleep disorders in the tutorial above.

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Also read this tutorial; as well as the 'related links' at the bottom of the links above.

  See you soon.

  Mick Murphy - Microsoft partner

• PIX 501, allows external clients only before the next hop to connect.

  Here's the problem:

  I have configured the Pix501 to accept PPTP connections and it works. I tried using a laptop with win98 on the same network segment (of the external interface). However, whenever my customers who are on a different ISP try to connect they may not. I tried with my laptop even home and another location, and all fail.

  I read recently that a router/firewall may block certain types of packets that do not establish PPTP connections. I think this is my problem, but I am unable to find information to pass on to my ISPS support staff.

  This is the router that provides the pix with the external connection is the problem in my view.

  Any thoughts?

  PPTP uses GRE packets. Ask them if they are blocking GRE, also ask if they block ESP and AH (types of IPSec packets, you can switch to IPSec if you determine that ISPS for your end-users block GRE to try to shake down to rates for dsl/cable "class business".)