The transition from ReadyNAS Duo ReadyNAS 104 v1

Similar Questions

• Pass the disk from ReadyNAS 104 again ReadyNAS 104 #26210568

  I just got a replacement from the ReadyNAS 104 factory. I swapped the drives ensuring that I kept the disc # correct. However, when I start the new NAS he don't know the discs. I need to "turn up the volume. However, I fear that will erase the data. Any suggestions on what to do?

  Hello ckovel,

  When you insert the disc on another chassis that is with the same model, you must insert them all to their respective bays before initializing the NAS. NAS should display disks and volume load.

  If this is not the case, one possible reason is the chassis and the disks do not have the same version of firmware.

  You should still be able to get support for it since it is to install the replacement. It is best that you contact the helpdesk to guide you through it. Use the previous case, it can be reopened and increase if necessary.

  Kind regards

• The transition from the bridge of one payment to another

  Hello

  We have a customer who currently treat offline credit card transactions that that they have their payment gateway set to 'process (process manually via the existing installation) offline '.

  Now, they want to put in place a bridge of the National Australia Bank (NAB).

  Could someone provide suggestions as to how it would approach the transition from the bridge of one payment to another whereas BC only allows gateway to a payment to be selected at a time?  In other words:

  1. Is it possible that the existing offline payment gateway and the new NAB gateway can coexist so that we could go through a test phase without interrupting the continuity of the customer with the treatment of existing credit offline transactions?
  2. Or do we have to "cut" their existing sales process until the new payment gateway is fully configured and tested?

  Any comments would be much appreciated.

  Gavin

  It is not that much work to spend from OFFLINE to NAB TRANSACT

  I'm not sure, that you need to worry too much on the implementation and testing before to cut more (unless you have a really high turnover store and you want to be careful)

  Perhaps you could watch you log in to your partner portal and reproducing the SITE you want to configure on (if you have an exact dupe). Then you can go about your tests on THIS site and get all tested and functional then cut on the settings when you are happy

  Good luck

  [email protected]

• Why the transition from the server causes error?

  I reported the error to the it Department, they respond as indicated below:

  "These errors are the result of a transition from server we are currently experiencing. As soon as the server transition is complete errors should stop. »

  «The transition of the server error has to do with displacement of the IP4 to IP6.» All pages work technically, but if you happen be routed through IP6 instead of the IP4, some of our pages will not appear due to firewall issues. »

  Does anyone have suggestions on what causes the error of IP4 to IP6?

  Thanks in advance for your suggestions

  -----------------------------------------------------------------------------------------------------------------

  Detailed description on the report of mail as shown below:

  Referring to the following link, some images cannot be display on 29 October.

  http://I1093.Photobucket.com/albums/i438/junk000/Error2.jpg 
   
   
  The other day, when I try to click on the following link and open it using IE8, the response is slow and getting the error on
  "Web Page error: 502 Bad Gateway!" with frontispiece USGS URL resolution error
  Please see the link for more information.

  http://I1093.Photobucket.com/albums/i438/junk000/error-6.jpg

  Do server not able to response to the loading of the web?  Is there anything to improve his performance on the server?

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Effect of movement not executed on the transition from State

  I have the following problem using view States, of transitions and the effect of movement

  I have a component panel and States state1 and state2.

  Panel is included in state1 but not in state2.

  When view state is changed from state1 to state2 I want to animate the front panel is removed.

  However, if I put a motion effect in my state of transition that it never runs because the Panel is removed before the effect plays.

  The only solution I found was to add a fade transition effect. This prevents the Panel to detach and the effect of movement is plays correctly.

  What continues? Is there a documentation explaining this? This could be a bug?

  Here is a sample application to demonstrate the problem. Panel1 has the problem and workaround Panel2.

  <? XML version = "1.0" encoding = "utf-8"? >

  " < = xmlns:fx s:Application ' http://ns.Adobe.com/MXML/2009 "xmlns:s ="library://ns.adobe.com/flex/spark" "

  xmlns:MX = "library://ns.adobe.com/flex/halo" >

  < s: states >

  < name s: State = "state1" / >

  < name s: State = 'state2' / >

  < / s: states >

  < s:Group >

  < s:Panel id = "panel1" y = "0" y.state2 = "100" title = "Group 1" includeIn = "state1" / > "

  < s:Panel id = "panel2" x = "150" y = "0" y.state2 = "100" title = "Group 2" includeIn = "state1" / > "

  < s:Button left = "300" label = "toggleState" click = "currentState = currentState == 'state1'? 'state2':"state1"" / > "

  < / s:Group >

  < s:transitions >

  < s:Transition fromState = toState 'state1' = 'state2' >

  < s:Parallel >

  <!-strange! 1 Panel is removed before the effect of movement time->

  < s:Move target = yTo "{panel1}" = "100" / >

  <!-the workarount. With a mannequin fade effect panel2 stays visible and move effect is executed->

  < s:Move target = yTo "{panel2}" = "100" / >

  < s: bland target = alphaTo "{panel2}" = "1" / >

  < / s:Parallel >

  < / s:Transition >

  < / s:transitions >

  < / s:Application >

  What is happening here is the Panel is removed from the DisplayList at the beginning of the transition before the passage has a chance to occur.  This happens by default unless someone tells the transition to remove the item at another time.

  There is a special logic built into bland who knows when an element is removed from the DisplayList so that he knows to say the transition to weaken the element before removing it.  This is why the workaround you mentioned works for your case.

  You will notice that if you use:

  
  

  The target fades out as long as his movement before retiring from the DisplayList.

  Normally, in this situation the transition must know when to remove the item from the DisplayList and you can tell him that using the RemoveAction tag, for example:

  http://ns.Adobe.com/MXML/2009"xmlns:s ="library://ns.adobe.com/flex/spark">
     
         
         
     
     
     

  
         
     
     
     
     
     
         
             
                 
                 
             
         
     
  

  Note that in this transition, I use a sequence and put the RemoveAction after the move, so the transition knows to move the item before removing it.

  By the way, thanks for the great code example!  When posting code on here is compile concise, complete, and I can quickly copy and paste into Flash Builder, I'm much more likely to focus on the issue.

• You cannot change the length of the transition from photo album

  Does anyone know why I can't change the length of one of the album transitions four other than 16 frames photo?  The transition moves way to fast to a half second really give me the effect I was hoping.  Working with fcpx 10.2.3.  Running on an iMac, El Capitan, 10.11.3.  Any thoughts?

  The duration of the transition is controlled by the amount of available handles extra beyond the edit point. To increase the duration, you may have the trim, the shots to put at the disposal of the media more. Hand and waving of the Edit with the tab at the top of the transition point.

  

• Lost the video when the transition from XP to Windows 7

  After the Upgrade from Windows XP to Windows 7, I lost the video.  Upgrade is not completely finished, but I can't do anything to fix the problem I have no display.  I need to go back to XP or difficulty somehow the video from the command prompt.  What can I do?

  How to uninstall Windows 7:
  http://support.Microsoft.com/kb/971762

  How to uninstall Windows 7 by using the Windows.old folder:
  http://support.Microsoft.com/kb/971760

• No sound after the transition from XP to Windows 7

  Original title: Audio becomes mute after upgrading Windows XP to Windows 7

  I upgraded from window xp family to an operating system of Windows 7 and my audio becomes mute,

  Please, how can I solve the problem?
  Thank you

  Hello

   

  (1) do you see any yellow exclamation or the symbol of the Red Cross for audio driver in Device Manager?

  (2) you download and install the latest drivers for the computer on the manufacturer's Web site?

  Here is the link: http://h20000.www2.hp.com/bizsupport/TechSupport/ProductList.jsp?lang=en&cc=us&taskId=135&prodTypeId=321957&prodSeriesId=499881

  (3) execute you troubleshooting methods referred to by zigzag3143x on July 19, 2012 in your previous post?

  Here is the article from the previous post: http://answers.microsoft.com/en-us/windows/forum/windows_7-sound/no-audio-device-installed/e80fae0f-f822-4392-a977-4ca65469d09b

  If you did not have the means of action, I suggest you perform the above troubleshooting methods and response with the result of the measures.

  I also suggest you use the below link to access the Device Manager and collect details.

  To open Device Manager, click Start, and then click Control Panel. Click performance and Maintenanceand then click System. In the hardware tab, click device, Manager

  Reference:--

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_dev_mgr.mspx?mfr=true

• CTRL-D to the transition from the one side?

  Used to be able to Ctrl-D to each side of an item on the CTI was at this side (beginning or end) now it always adds a double transition in the face of both ends of the clamp. I rarely do this, how I add the transition to one side using Ctrl-D or a Variant?

  Thank you!

  Make sure that the clip is not selected.

• Bug in the transition from the groups of tabs when the mouse is over a tab

  I use two groups of tabs, each around 3-10 tabs open. I press Ctrl +' to switch between groups of two tabs. Everything works fine except when I have the chance to have the mouse cursor positioned on a tab when I press Ctrl +'. In this case, Firefox seems to get confused and I get an unpredictable mixture of the two groups of tabs tabs. I have to then move mouse tab and then press Ctrl +' twice to the tab group good I tried to move on. It's boring.

  I think it started in FF29, but I'm not sure.

  First of all, I would like to confirm that it is a bug. Secondly, I would like to see it attaches. I tried to find info on this several times without success. Anyone know anything about this?

  Thank you.

  OK nevermind, I did some more research and found a bug in Bugzilla for it. The bug has been fixed and I've confirmed with a night generation. Looking forward from the set in a regular release.

• during the transition from Outlook Express to Windows Live Mail, is the address book data stored and also the info in files

  I'm afraid that if I upgrade the form Outlook Express to Windows Live Mail, I will lose all e-mail addresses in my address book current as well as the information contained in the files - models etc.

  If you install WLMail on your XP machine, it has to import messages and addresses automatically and nothing will be lost of OE.
   
  If you like WLMail better than OE, you are a person better than I am.
   
  For specific questions from WLMail, ask here.
   
  Windows Live Mail Forum
  http://windowslivehelp.com/forums.aspx?ProductID=15
   
  PS It has nothing to do with Hotmail. I don't know where Christophe that came out of your post.

• can I use easy transfer or transfer Assistant during the transition from XP to Vista / 7?

  XP - XP Easy Transfer

  What I can or I do not use Easy Transfer XP to Vista (or XP to Windows 7?) to transfer files, settings, etc. from a XP Pro (SP3) to another XP Pro PC, or what I need to use the files & Settings Transfer Wizard?  I can't find a definitive answer of 100% with it in correspondence of forum.  What if I transfer via an external hard drive or a shared network folder?

  [I guess there is no XP easy transfer dedicated to XP tool]

  Use the easy transfer program and send data on a cd or external hard drive.

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=2B6F1631-973A-45C7-A4EC-4928FA173266&displaylang=en

  The foregoing is for xp, but both vista and win7 already.

• Windows Update feature connects to the Windows Update server after the transition from XP to Windows 7 Pro.

  Updated XP PC to Windows 7 Pro 64 bit.  First upgrade failed due to the bad version of Win 7.  (Distorted version of seller).  Correct version relocation has left two versions installed so I started reinstalling the correct version and reformat selected before continuing.  (21/04/16)  Installation proceeds correctly, validated and activated license, but the update function didn't work.  One version on the disc after the previous action.  Then I downloaded and installed IE 11 manually the version 11.0.9600 of Microsoft (same date) and then downloaded and installed MSE from Microsoft 4.9.218.0 version (same date).   MSE updates have not downloaded initially until I ran Win update problems solving.

  I have since run program sfc/scannow (without problems of integrity or repaired files), update Windows utility for troubleshooting and Fixit programs.  I also stopped the update service, delete the appropriate configuration of software and restarted the service records.  Still not connection with update server.

  Download and install the following update manually. This greatly speeds up the update of Windows on new installations of Windows 7.

  Installation and research updates is slow and high utilization of the processor occurs in Windows 7 and Windows Server 2008 R2
  https://support.Microsoft.com/en-us/KB/3102810

• \b in the transition from text to text elements. How to get just the plain text?

  I use C++ FDK and get TextItems with FTI_String from the active document. But the text in the text elements contains characters that do not appear in the text. For example, \b. What is this character and how can I get only the plain text without any character of metadata of FrameMaker.

  Ch,

  I think you could see tabs. Presented as an escape sequence, \b translates the BACKSPACE (0x08) ASCII character. For some reason, that's how the tabs are represented when you get the text of a document with the API. You expect to show that \t or ASCII 0 x 09, but they did not.

  There is no way to avoid retrieving a character entered by the user when you F_ApiGetText(). You must simply do a search and replace once you have the string in your code.

  I hope I understand what you're asking here.

  Russ

• Management of the transition from the page = reverse do not work.

  Hello

  I used the same code in the discussion Re: Mobile Application and direction = "reverse" Transition effect . :

  apex.jQuery.mobile.changePage ('f? p = & APP_ID.:1: & SESSION.', {transition: "flip", direction: "inversion"});

  But the result isn't the reverse version of transition. It also what type button data direction = "reverse" attribute

  What do I do?

  Apex version is 4.2.5.

  a sample application: https://apex.oracle.com/pls/apex/f?p=67666:1:9314128408408

  Ok. Here is the original http://demos.jquerymobile.com/1.2.0/docs/api/methods.htmlsolution:

  //transition to the "confirm" page with a "pop" transition without tracking it in history  
  $.mobile.changePage( "../alerts/confirm.html", { transition: "pop", 
  reverse: false, 
  changeHash: false }
  ); 
  

  the inverse attribute is true or false. :

  Use on apex: apex.jQuery.mobile.changePage (...)

  then its works fine :-)