Unable to start after installing SP3

Similar Questions

• Windows does not start after installing sp3

  I had windows xp with sp2 and sp3, I downloaded. Once the download is complete it asked me to restart the computer. Windows will not go up. No error message, but it will work when the system is in safe mode. In addition, windows update does not load. Any ideas?

  You are a candidate for this patch before installing SP3...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=UK&LC=en&DLC=en&softwareitem=PV-60484-2

  .. you are if your PC is a HP Pavilion and Presario, Media Center and has an AMD processor

  To find out if you have an AMD processor...

  • Hold down the Windows (between Ctrl and Alt) key and press Pause break
  • Your processor type is shown in the computer: section (see below)

  You can do a restore of the system in safe mode to get rid of the SP3...

  http://support.Microsoft.com/kb/306084/en-GB

  Tricky

• I have problems of continuous loop trying to start after installing SP3

  I tried to boot into safe mode and other options, but it does not start and it won't start either my drive (says there is a damaged my disk file).

  Any ideas on how to get started so that I can remove SP3?

  PS - very disappointing that there is a lack of support from Microsoft on this subject - unless you pay £46 - it was caused by their update and I think they should fix it for free!

  Hello

  Please follow the steps below: good luck

  Thank you

  Thomas

  http://support.Microsoft.com/kb/950249

  Method 4: Use the Recovery Console

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows

  If you cannot remove Windows XP SP3 by using one of the previous methods, follow these steps:

  1. Insert the Windows XP CD in the CD drive or in the DVD drive and restart your computer. When you receive the following message appears, press a key to start your computer from the Windows XP CD:
     Press any key to boot from CD

     Note The computer must be configured to boot from the CD or the DVD player drive. For more information on how to configure your computer to start from the CD or the DVD player drive, refer to the documentation that came with your computer or contact the computer manufacturer. Alternatively, you can use a Windows XP boot disk. For more information, see the following article in the Microsoft Knowledge Base:

  305595 (http://support.microsoft.com/kb/305595/) how to create a boot disk for an NTFS or FAT partition in Windows XP
• When you receive the Welcome to Setup message, press R to start the Recovery Console.

  Note Several options will be displayed on the screen.

• Select the correct installation of Windows XP.

  Note You must select a number before you press ENTER, or the computer will restart. Generally speaking, only the 1: C:\Windows is available.

• If you are prompted to type a password to admin, do. If you do not know the administrator password, press ENTER. (As a general rule, the password is empty.)

  Note Do not continue if you do not have the administrator password.

• At the command prompt, type cd $ntservicepackuninstall$ \spuninst, and then press ENTER.
• At the command prompt, type batch spuninst.txt, and then press ENTER.

  Note The Spuninstal.txt file appears. As the file scrolls down, you will see errors and files that are copied. It is a normal behavior.

• After Windows XP SP3 is removed, type exit and press ENTER.
• Restart the computer in safe mode. To do this, press F8 when the computer restarts.

  Note After you restart the computer, the computer may stop responding, and you will see a black screen. The mouse works. In this case, restart the computer by turning off the computer, and then turn it back on. The second reboot allows you to open a session.

• When the computer restarts, Windows Explorer (Explorer.exe) does not run and the icons of Windows and the Start button are unavailable. To resolve this issue, follow these steps:
  1. Press CTRL + ALT + DELETE and then click Task Manager in the Windows security screen.
  2. Click file, and then click new task (run).
  3. In the Open box, type regedit, and then click OK.
  4. Locate and then click the following registry subkey:
     HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\RpcSs
  5. In the Details pane, right-click ObjectName, click modify, type LocalSystem in the data value box and then click OK.
  6. Restart the computer
• Use one of the previous methods to remove Windows XP SP3 from your computer.

For more information about how to install and use the Recovery Console, click the number below to view the article in the Microsoft Knowledge Base:

307654 (http://support.microsoft.com/kb/307654/) how to install and use the Recovery Console in Windows XP

If you need assistance on how to install, reinstall, or uninstall Windows, visit the Microsoft Web site at the following address:

http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall (http://windows.microsoft.com/en-us/windows/help/install-reinstall-uninstall)

• computer does not start after installing sp3

  I did a clean install and my computer went to when I bought it, it's a compaq windows xp media center edition 2005, it is now under service pack 2 when I try to download sp3everything how ever seems to go ok but when I restart a black screen appears with start in normal mode it waits 30 seconds, try to start and guard that goes back to the same screen , I finally go in safe mode and restore back to sp2 can anyone help pls

  See aid to Steveg100 here...

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/getting-blue-screen-reinstalled-by-use-of-recovery/e7791a6c-88bb-400C-bed4-0f612d099114

  Tricky

• HP PAVILION HPE h8-1192d: could not start after installing new graphics card

  I recently bought a Gigabyte GTX 750 Ti Black Edition to replace my old. But it will not start after installing on my h8-1192d, and stuck on the screen flash hp. Help, please!

  Hello

  NVIDIA GTX 7xx or 9xx series graphics cards will not work in your PC.  The BIOS in "chicago" mothererboard is not compatible with the video BIOS in the graphics card.  You will need to get an older card chart such as the one of the below listed OEM HP graphics cards. Depending on the graphics card, you may need to replace the power suplly.

  

• iPhone 4S.  Stuck on request to post a link to iTunes.  Has started after installing the recent software update.  Tried to turn but the iTunes link keeps coming.

  iPhone 4S.

  Stuck on request to post a link to iTunes.

  Has started after installing the recent software update.

  Tried to turn but the iTunes link keeps coming.

  You can not connect the phone to iTunes as requested?

• DVD player doesn't work after installing SP3 for Windows XP.

  DVD player doesn't work after installing SP3 for Windows XP. That it disappeared from "MY COMPUTER". Device Manager sees it, but there's a yellow exclamation mark over it. See the BIOS of the motherboard and it still works in the BACK. I know SP3 is a collection of updates, but I'm not sure that is my problem. I suspect it's one of the more recent cause I have Windows automatic updates is turned on. Thank you.

  Hello Superhornet142,

  Thank you for your message.  Click HERE and run the FixIt!  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• No start after the sp3 of Windows install

  After the installation of sp3 for windows xp home, in normal mode and safe mode, windows starts in safe mode and show the installed sp3 but does not start in normal mode.

  1. how to remove Windows XP Service Pack 3 from your computer
  http://support.Microsoft.com/kb/950249

  2. the measures to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717 TaurArian [MVP] 2005-2010 - Update Services

• Unable to start after you run the product recovery disc

  Hello

  My laptop was a dual boot with windows XP SP3 and ubuntu

  1. He was infected by the virus and when I tried to clean it I removed the wrong file "services.exe", whereas windows does not work good there

  2. when I tried to uninstall the windows update, I get the error following error: 1068: the dependency service or group could not start

  3. so today, I found the toshiba recovery disks, I run and it commpleted, but now am not able to start my laptop.

  4. when I try to re - install windiws xp I got the error below "couln can't find NTLDR.

  Guys, your help will be much appreciated

  Hello

  > I run and it filled, but now am unable to start my laptop

  Are you sure that installation completed successfully? Looks like the damaged MBR or cannot be attributed

• After installing SP3 on XP can not get computer to boot...

  I installed SP3 on XP. When I turn on the computer, it takes me to the screen to select a start upward. I does not start in safe mode, when I choose the other options of the Windows XP screen comes up but it does not start...

  Hello

  Try to uninstall Sp3 via the recovery console.

  Here are the steps that you must follow

  Thank you

  Thomas

  Link: http://support.microsoft.com/kb/950249

  Method 4: Use the Recovery Console

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows

  If you cannot remove Windows XP SP3 by using one of the previous methods, follow these steps:

  1. Insert the Windows XP CD in the CD drive or in the DVD drive and restart your computer. When you receive the following message appears, press a key to start your computer from the Windows XP CD:
     Press any key to boot from CD

     Note The computer must be configured to boot from the CD or the DVD player drive. For more information on how to configure your computer to start from the CD or the DVD player drive, refer to the documentation that came with your computer or contact the computer manufacturer. Alternatively, you can use a Windows XP boot disk. For more information, see the following article in the Microsoft Knowledge Base:

  305595 (http://support.microsoft.com/kb/305595/) how to create a boot disk for an NTFS or FAT partition in Windows XP
• When you receive the Welcome to Setup message, press R to start the Recovery Console.

  Note Several options will be displayed on the screen.

• Select the correct installation of Windows XP.

  Note You must select a number before you press ENTER, or the computer will restart. Generally speaking, only the1: C:\Windows is available.

• If you are prompted to type a password to admin, do. If you do not know the administrator password, press ENTER. (As a general rule, the password is empty.)

  Note Do not continue if you do not have the administrator password.

• At the command prompt, type cd $ntservicepackuninstall$ \spuninst, and then press ENTER.
• At the command prompt, type batch spuninst.txt, and then press ENTER.

  Note The Spuninstal.txt file appears. As the file scrolls down, you will see errors and files that are copied. It is a normal behavior.

• After Windows XP SP3 is removed, type exit and press ENTER.
• Restart the computer in safe mode. To do this, press F8 when the computer restarts.

  Note After you restart the computer, the computer may stop responding, and you will see a black screen. The mouse works. In this case, restart the computer by turning off the computer, and then turn it back on. The second reboot allows you to open a session.

• When the computer restarts, Windows Explorer (Explorer.exe) does not run and the icons of Windows and the Start button are unavailable. To resolve this issue, follow these steps:
  1. Press CTRL + ALT + DELETE and then click Task Manager in the Windows security screen.
  2. Click file, and then click new task (run).
  3. In the Open box, type regedit, and then click OK.
  4. Locate and then click the following registry subkey:
     HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\RpcSs
  5. In the Details pane, right-click ObjectName, click modify, typeLocalSystem in the data value box and then clickOK.
  6. Restart the computer
• Use one of the previous methods to remove Windows XP SP3 from your computer.

For more information about how to install and use the Recovery Console, click the number below to view the article in the Microsoft Knowledge Base:

307654 (http://support.microsoft.com/kb/307654/) how to install and use the Recovery Console in Windows XP

If you need assistance on how to install, reinstall, or uninstall Windows, visit the Microsoft Web site at the following address:

http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall (http://windows.microsoft.com/en-us/windows/help/install-reinstall-uninstall)

• Black screen with mouse pointer count on reboot after installing SP3

  I tried to install Service Pack 3 on a PC running XP Home Edition (new installation).

  Although Microsoft Update has finished installing SP3 and the computer reboots, I get the XP installation screen base with the message "Please wait...". ", which disappears after a few seconds, leaving me with a black screen with only the mouse pointer.

  The mouse pointer moves then the PC broke down, well that no matter how long I leave nothing happens.

  I tried to uninstall SP3 and do it again (when I Uninstall SP3, Windows starts very well) and also uninstall SP3 as well as my Antivirus and try the installation again. But whenever I'm just left whit black screen.

  Try to update with the custom option.  I had problems like this before.  Usually you are missing a driver or something of this kind that makes you hang.  To update while the custom option, with the exception of SP3.  Reboot several times the installation of updates with the "Custom" option  Once all updates have been installed except SP3, you can try SP3 and see what happens.  This usually takes care of it when I have the same problem. Serving the community one computer at a time www.therushvillecomputerguy.com please post a reply to let us know whether or not our response helped.

• Unable to sync after installing iOS 10.0.2

  After installing iOS 10.0.2 this morning, I was not able to sync my iPhone 6 s + with my MacBook Pro running Sierra. Y at - it something I need to do. I turned off the phone and computers and they started separately, but not luck. I tried to sync wireless and with 2 different cables of lightning, but not luck.

  Suggestions?

  Thank you

  Jim

  A little more information:

  Our two iPads works sync iOS10.0.1 perfectly.

  This is the message I get when I try to sync my iPhone.

  «The iPhone "iPhone 6 s +" cannot be synced because there is not enough free space to hold all the items in iTunes (Go 56.14 additional required) library.»

  I have not changed that is to be synchronized. I'm sure that something is wrong with the 10.0.2 update.

  Jim

• Computer OS used to start after installing windows 10

  Hello im having problem starting my system after installing windows 10. I did the install and it worked fine since the upgrade to 8.1. But then I tried to format the drive and in the menu format, he's stuck at 2%, and then I restarted the computer. Now it will hang at the hp logo and go back to the same logo. Do I have to replace my hard drive?

  What I understand, if you have completed the 10 Windows Installer and everything has happened until the end, then you are supposed to be able to do a clean install with the download of Windows 10 DVD or USB.  With a working computer, GO to THIS PAGEand scroll down to the button "download tool" selection the 64-bit version.  Once clicked, it will ask you if you want a DVD or USB for the iso.

  Once it's done and you have the DVD or the USB version, see if you can install Windows 10.  If this fails, you may need to replace the hard drive.

• Does not start after installing new video card

  Hello, I have a desktop H8-1284, and the video card went a few days ago. So I bought a video card Geforce GTX 650, and after installing the card and the computer starts, it hangs just at the start of the HP logo screen. So I put an old geforce 8800, and she starts without a problem. When I try the new card Geforce GTX 650, the same thing, just hangs at the splash screen.  I checked the bios and it doent seem to be something there that can help wouild. My diet is 460 w, and the new map needs of 400 w, any help will be greatly appreciated

  Hello

  Most of the cards PCI-E 3.0 are retro-compatible with the PCI-E 2.0 slots.  However, in order to get the PCI-E version 3, you must use a processor Ivy Bridge.  Look at these specificationsfor a typical NVIDIA GTX 650.

• Windows 7 takes 15 min to start after installing Labview 2012

  Hello

  I need help on this, is this a bug?

  The problem is that on my laptop after installing Labview 2012, it takes about 15 minutes to start, this happens every time a restart or start my laptop.

  At first I thought something with my laptop, but then my colleague also installed Labview 2012 on his laptop and has exactly the same problem, the difference is that his new laptop and is running windows 7 Professional 64-bit, mine is older and is currently running windows 7 32-bit professional.

  I tried to disable the services NOR, but has not solved the problem, but when I disable all windows services that start at startup, the startup is fast.

  Also note that I had Labview 2011 installed before and I didn't have this problem before.

  Tried also to find something in the registry, but nothing.

  Any who have this problem, or a solution to this?

  Thanks in advance

  This problem seems to be resolved, but then he come back again a few days later

  I did many tests in my laptop and found it to be in the "Service of Network Store Interface" service (INS). Disabling this service, you have your problem solved, but there is another problem, you lose the network.
  This happens because the "DHCP Client" service depends on the national statistical institutes.

  Also, this issue seems to occur only when the PC is in a domain and I'm in a windows server (Windows SBS2008) domain.

  Then I found that if you set manual this services which depend on national institutes of statistics (DHCP Client, DNS Client, IP Helper, network connections, local awareness network) and also put INS manual
  You must also disable the "Workstation" service that also depends on national institutes of statistics (why turn off? Because there are 3 services that depend on the workstation service, they will require to start, and then it will force NSIS to start, then long boot, if you really need of the dependent services on workstation, do the same as for them)
  Not also need uncheck this services in msconfig window if they are checked, and then the PC will boot normally without a network.

  When you start, you should go to services and start the DHCP Client for the network (and the other if you really need)
  This will force also NSIS to start and other services that depend on the national statistical institutes.
  The first time the PC restarts, you may need to reset these services to manual in the services window, I had to do, and then in sebsequent boots, they have been already set to manual
  If you leave right on the dependent services in automatic or automatic (delayed start) it will force NSIS to run and start time will go to + - 15 min

  Because you must manually start "DHCP Client" for the network, here's a solution to do it automatically after have connected you:
  1 - Go to control panel, and then open administrative tools
  Task 2-open Scheduller
  3. on the right click "Creat fundamental task.
  4. in the first window give a name ("DHCP" for example) and press next
  5 - Click on "When I Logon" and press next
  6 - click on "Start a program", and then press next
  7. in the "program/script" insert: net
  8. in the "Arguments" insert: start "DHCP Client".
  9 - Press 'Finish' and you're done