Vertical lines shows that when using document feeder / have given help and discussions, no luck
I have two printer hp models 1536. Two of them have a vertical line when using the loader to scan or copy documents.
When you place the point on the glass, scanning or copying is clear.
Reading the discussions... tried to plug directly into the wall, cleaned feeder and glass, etc.
I still have this problem
Any ideas?
Driver or firmware problem?
The question is probably not a driver or firmware issue - it is probably a task on the thin glass used for playback through the ADF. Try to clean the glass broadband of 1 "to the left of the main scanner glass. A tiny spec can cause the problem you are experiencing. It can help to hold a flashlight almost parallel to the scanner glass to highlight all the stains on the glass.
Tags: HP Printers
Similar Questions
-
HP photosmart 6510: error on hp photosmart 6510 showing-95 when using scan to email
My photosmart hp 6510 displays error - 95 when using scan to email. Help!
Hello @twinec, greetings!
Thank you for joining the Forums of HP Support! I came across the question you posted, and I want to help you with the best of my knowledge.
You can try a manual DNS address assignment to fix most of the analysis of the questions by e-mail. Try the steps mentioned below and check:
- Get the IP address of the printer, you can touch the 'Wireless' icon on the Control Panel printer to get the IP address.
- Type the IP address in your web browser to get the EWS page on your computer printer.
- Go to the 'Network' tab - click on "wireless (802.11), and then click «network address (IPv4)»»
- Click on the radio button that says 'Manual of the DNS server' and under manual type favorite 8.8.8.8 and manual replacement enter 8.8.4.4 (it is Google's DNS server address)
- Save the settings. Restart your modem, router and printer.
Let me know how it goes! Good luck
See you soon
Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!
-
Can I use your Apple TV when I do not have a modem, and I use the Wifi in the hotel room?
Thank you!
Probably not, but depends on the hotels wifi access. most of the hotels that I stay in you will have to "login" via web browser and the ATV doesn't have access to any browser...
your best bet would be to broadcast directly from a mobile device connected to the tv in your hotel via a HDMI adapter...
-
Hi, my problem is that when I download from Premiere Pro CS6 and creative cloud
Hi, my problem is that when I download from Premiere Pro CS6 and Cloud Creative aperece me updated, but it can't find the file anywhere, as if had not been cleared.
32-bit Windows
Please if you can help me with this problemPremiere Pro CS 6 is only compatible on the 64-bit computer. Therefore, it is not available for the launch.
Please check the link for more details below:
-
Hello
I tried several days create a workflow to automatically remove the E1000 adapters on a virtual machine and its replacement by Vmxnet3 while maintaining the configuration of the network adapters.
Everything works fine with Linux VM (as the configuration is automatically preserved) but I have an error on the virtual Windows computer where I have to run a Powershell script (tried with batch also script) with guestScriptManager package.
Every script I try to run on a Windows 2008R2 VM does not reach the same step: create a temporary file in the comments. Error: "guest authentication that is used doesn't have sufficient permissions to perform this operation (workflow: create a temporary file in the task (item1) invited / Scriptable #8)"
Strangely, I am able to run a script, one or two times to just after a VM deployment and then I'm stuck with this error.
I tried with the local and domain administrator with no luck. I have no other description or log on to the error...
Any help would be appreciated
Thank you
For those who are wondering, I just updated my 5.1 ESXi Update 2 and the problem is solved.
Thanks to this thread: https://communities.vmware.com/thread/403326
-
Windows XP Professional SP3 32-bit - my help and support center is missing. When I click, it says start the service named 'help and Support '. How do I do that?
* original title - lack of help and Support Center *.
Thanks for the help :) Also, when I open my computer or any other program like the trash, the bar on the left side of the screen with the options (i.e., in the trash, which allows me to empty the tray) isn't here... Is there anyway that I can get it? I thought it was something to do with the help and support center, but even after that I got help and assistance, that sidebar is not there...
For this bar, open desktop (or any other folder). Go to tools-> Folder Options and in the general tab, check the show common tasks in the option box of records under the tasks column. The bar appears.
I hope that helps!
-
I want to get Acrobat for home use, but I have 2 desktops and 2 laptops. Y at - it an alternative to stand-alone purchase of 4 copies of the software?
Hi JStavolaND78,
I would like to inform you that there is only a single license for subscription an acrobat.
If you need a single license for several systems, you can opt for the volume license.
You can read this article for more information on volume licenses: find information about Adobe Volume licensing plans
Let us know if you need additional assistance.
Concerning
Sarojini -
I bought the new 6 s iPhone with 64 GB of storage in December. A few days ago I updated to iOS 9.2.1 and I got a notification the next day saying that my storage was almost full. I was shocked because I have not yet used half of the 64 GB and before I upgraded to the latest updated everything worked well. Also, on a side note, game Center does not work and when I try to open the app it's just a blank screen and when I go into settings, click on the play icon, it does not even open.
Back to the problem of storage, I don't not even use a lot of my storage upward. Look at the photo for reference. This photo was taken after I updated.
So I am very confused right now with my phone and I have only had it a month ago and it's already the case. It does not make sense to me to have only 4.84 GB free. I used 6,76 Go on applications, and I have 20 apps and I understand that, but whence this other 44 gb?
Why do we say I used 44,59 GB of data and documents when I don't? Could be a problem due to the update to iOS 9.2.1?
BradCalifornia15 wrote:
So I am very confused right now with my phone and I have only had it a month ago and it's already the case. It does not make sense to me to have only 4.84 GB free. I used 6,76 Go on applications, and I have 20 apps and I understand that, but whence this other 44 gb?
Why do we say I used 44,59 GB of data and documents when I don't? Could be a problem due to the update to iOS 9.2.1?
Connect your phone to iTunes on your computer and see what the ability the bottom bar shows for storage. You can have one large amount of 'other' data which may indicate a corrupted sync or corrupted update. If you have backed up with iTunes before you update, try to restore the backup.
Take a look at the Board to the alarm user.
-
I tried to do a right click on bookmarks, list on the left, but no menu appears. I do not need or want of two lists of favorites, and I prefer to use one on the right that shows only when I click it. The news is empty (no registered bookmarks), but this empty column takes place, I don't want not wasted!
{Ctrl + B} opens and closes the bookmarks bar.
-
OfficeJet pro 8600 black vertical lines of print when copying
I got a new of OfficeJet Pro 8600 a couple of weeks, and it worked fine until today, when I tried to copy something. I can always print from my pc and scan without problem, but when I try to copy a document (if I load it into the tray or put it on the scanner) the page comes out covered with black vertical lines of different sizes. It seems that this isn't the ink or the scanner since I can print from my pc and analysis very well.
Help, please!
This unit is plugged into a wall outlet directly? If this isn't the case, then try to connect the unit to a wall outlet directly.
The 8600 Officejet Pro has built in the surge protector and double this feature may cause some problems.
Also, try to reset the printer hard:
* Unplug the unit while the printer is on
Disconnect the other end of the power cable from the wall socket direct
* Wait 30 seconds
* Plug the unit to the topLet me know if it helps.
-
I've updated my Ram in my 5532 Acer Aspire from 3 GB to 4 GB and
When I run a check on my computer using my Norton 360 it shows
I have 2 GB and I have an empty slot for the ram, but I have a 2 GB
in it. What can I do about it? How should I do?Make sure that the RAM module is installed correctly.
If you are running Windows 7 32 bit, you can recognize 3.2 GB of RAM.
My PC running the 32-bit version or 64-bit Windows?
http://Windows.Microsoft.com/en-us/Windows7/find-out-32-or-64-bit
-
Vertical lines on the Photos using HP Photosmart Plus
I just bought the HP Photosmart Plus last week. The 1st photos I printed, using the paper supplied with the printer (HP Advanced), went well. My wife bought "Printworks' 4 x 6 sheets of brand. First of all, I had a paper jam. I don't know if it's relevant. The photos I printed had 12 visible vertical lines. He seemed separate from 12 vertical strips sewn together. So, I went out and my HP Premium Plus paper. It still looks like 12 vertical strips. There are noticeable verical about 1/2 in. lines. I also think it seems grainy. The photo was taken with a Nikon 10Mpixel, so resolution is not a problem. I printed out as some other pictures and they had the same problem. I was careful about settings, choose the premium more paper and choosing the best quality. I also cleaned the print heads. Any ideas?
Joe S.
All the:
I finally had time to shoot the print head and cleaning it. This seems to have solved the problem.
-
Unwanted horizontal line shows that in Firefox
A horizontal line appears below the chart labeled '' this is unaffordable '. It shows that in Firefox. Any suggestions?
www.ourhealthcarecrisis.com
(many thanks to those who helped me to get this site to work)
Move your tag to before the word "Healthcare" as shown below - it is currently at the beginning of the
http://this is unaffordable"/ >
Health care insurance companies
-
Only the blue background shows only when using the Oracle cards
Hello world
I am new to oracle spatial. I just tried demos of oracle cards. Now, I want to display my own data source and view the files of my own form in the maps of the oracle, but he just gives blue background. I checked with the srid... his right.
I am not able to rectify my mistake... where I'm wrong. Help, please.
Need urgent help
Aid must be assessed.
Thank you
REMAHello
I've seen generally that when there is no data to display, maybe no spatial index?
You should review the mapviewer log file and look for errors generated. What happens if you return your theme in mapbuilder, it works there?
You say exactly what you are doing, what your data etc.
Jon -
I have a little Acer One connected to my bigger screen. I use the free version of AVG, I've read can cause problems and I have also read that I needed to update my version of Java and this could lead to freezing and no response in IE8. Come to find out that I didn't even have Java so you download the version for my computer but nothing changed. I need an answer to help my computer. He arrived at the point where I can't even get anything without IE8 freezing and when I try to wait just outside, it will specify that it does not.
Someone has fixes out there for this? I ran the Microsoft Fix It tool - nothing. I have disabled all addons just to see if it can help, but - nothing. I am at a loss here. Help, please.
Thank you, joy
could be malicious or ie8 is corrupt.
There are several options,
1. clear your temporary internet files, go to tools, internet options, under browsing history, click on remove in the next box, just check and uncheck the box given to preserve your favorite Web sites.
2. Remove avg using the removal tool:
http://www.Avg.com/ww-en/utilities
3. install Microsoft security essentials:
http://www.Microsoft.com/en-US/Download/details.aspx?ID=5201
Download MSE
http://experts.Windows.com/w/experts_wiki/89.aspx
MSE installation checklist
READ the checklist
4. make sure that your system is clean:
Download, install, update and scan with these full free malware detection programs:
Malwarebytes (MMFA): http://www.malwarebytes.org/products/malwarebytes_free
SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
Remove all found, restart, and run again until analyses race clean, these can be removed later if you wish. Perform analyses to one at a time, please.
5. go in Microsoft updates and ensure you are fully patched and updated analysis of the express, install, then do a custom scan and install Rootkit updates.
6 uninstall ie8 then reinstall ie8, if you installed SP3 after ie8, read this:
http://support.Microsoft.com/kb/950719
After back with the results.
Maybe you are looking for
-
Firefox dekstop is missing, because the toolbar button
I don't know why, my Firefox can not be at the top, click under the toolbar... When I click, appear to ' Add/edit button, change toolbars, refresh the toolbar.What should I do now?
-
Pavilion dv4 2123 TX: TX HP Pavilion dv4 2123 wireless network connection problems
Machine will connect to the wireless network, but not connect to internet. Have restarted, hard-rebooted and uninstalled/reinstalled all the drivers for network card. Any help is welcome! Thanks in advance.
-
losing el capitan after switching to windows
I am Andrew of France, my problem is 1 macmini installed with yosemite boot camp windows 7 works perfectly well 2 I upgraded to el capitan yosemite I better not bootcamp 3 I'm having boot disc for windows 4 now Windows can't start the mac even drive
-
Pavilion 15 e056sr: I forgot the administrator password
HelloI forgot that my administrator password and can't start my laptop. After 3 unsuccessful attempts, there is a message: deactivation of the system 59823511.Could you please help me.
-
Is no longer able to access the drives specified on my system
I have a hard drive connected to my computer in auxiliary. It consists of four partitions. The volumes for these are Fat32 or NTFS. However, now my computer says the volume one of the partitions is now RAW (what is?). Anyway, I'm unable to access one