VMware ESXi scale up vs. scale out

Similar Questions

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• How to check for hardware vmware esxi 5 is installed on

  Hello

  I took a vmware esxi Server 5.

  I need to evaluate on what hardware esxi 5 server is installed on. Is it possible to do - apart from opening the case?

  Thanks a lot for any help

  MIchael

  Hmmm... There are the available IMS and supervision of Adaptec in ESX server. Check out these threads just to feed the part of the brain

  http://communities.VMware.com/thread/158690?start=75&TSTART=0

  http://www.Thomas-Krenn.com/en/wiki/Adaptec_RAID_Controller_Monitoring_in_VMware

  Glad that you got your query using rvtools...

  Cheerios...

• License of VMware ESXi

  Hi all

  I want to know if the VMware ESXi can be used situation?

  Hi William - Welcome in the community.

  The answer is Yes.

  The free version of ESX, I can be uised in production - although you won't get any agreement with her support - so you don't have to rely on VMware etc. communities for support (not ideal for production)

  There are a series of oif types of licenses that can be puyrchased - according to your needs.

  I think VMWare are happy with thismodel, because once most companies see the benefits of VMware virtualization and save on hardware, etc., most go to buy licenses that include additional features such as vCenter, support, vMotion and so on.

  ESXi (free version) has not built DR (like HA), or the distribution of resources (DRS) - If you are quite limited.

  In short, although that - Yes is the answer to your question.

  PS - Your first install ESXi will give you access to all the functions for a limited time - but once this period runs out, you will be limited to a limited ESXi installation. ESXi is the complete functionility of normal ESX, when it is fully licensed.

• VMWare ESXi is not responding

  Hello
  
  I have a server at home with a Q6600 Quad Core and 8 GB RAM running with VMWare ESXi 3.5 for about 8 months now. I have 2 warehouses of data, with 1 TB (SATA HDs), each with 150 GB free and the other with 240 GB free. I have 9 virtual machines running 24 x 7 on it. Everything has been done, until yesterday.
  
  Out of the blues, I stopped to get the answers from the MV in the ESXi. Initially, I was able to connect using the Client Infrastructure but, when if I tried to get information from any virtual computer, I receive a message that the virtual machine could not be reached. Looking at the info from the host, he would show me info network, cpu, memory, but when I tried to reach the data store, it would normally stop responding. I couldn't open the located data store where ESXi is installed once, and all virtual machines were there. Now, I can not connect more, and I don't really know what to do.
  
  What is the best course of action to diagnose the problem? I can access the ESXi screen without problem, but I don't know what to do. I thought to reinstall, maybe with version 4.0, but I'm not sure I should do it. Where (and how) can I access what anyone who could help me figure what's wrong?
  

  TKS

  Try these options in the following order:

  1 reset the Management Agents: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net.html

  2. restart Management Network: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net2.html

  3. restore the vSwitch standard: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restore_stnd_switch.html

  4. full reset: you loose all the configurations you made on the ESXi server, but the guests are kept.

  http://pubs.VMware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=Setup/t_reset_the_configuration_defaults.html

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0

  Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.

  On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?

  Hello

  You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter

• VMware ESXi monitoring

  Hi all

  does anyone have experience with followed Bigbrother to host VMware ESXi?

  In particular, I am interested monitor consumption of resources (CPU, memory, data warehouses) ESXi hosts.

  I am happy to receive any information about this topic:

  -experience in general

  -scripts

  -Links to the already existing scripts or documentation

  - ....

  Best regards

  Stefan

  Hello Stefan,

  There is an existing extension that accomplishes what you want and it can be found at http://communities.quest.com/docs/DOC-5658 - I have not implemented this myself, but I've heard other users that it works very well. Let us know if this is consistent with what you are looking for, and we would be happy to help you with questions of integration.

  Best,

  John McNelly

  Big Brother Team

• R710/R720 - Dell customized Image of VMware ESXi 5.5 Update 2 - megaraid_sas version specific?

  That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:

  www.dell.com/.../DriversDetails

  The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:

  www.Dell.com/.../manuals

  indicates that a specific version of the megaraid_sas driver must be installed.

  Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?

  I just ran the upgrade on a R710 and it's the megaraid_sas version installed:

  ~ # vmkload_mod s megaraid_sas | grep Version
  Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014

  Thank you.

  Hello

  It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02

  megaraid_sas - 06.803.73.00

  Page 5 ftp://ftp.dell.com/Manuals/all-products/esuprt_software/esuprt_virt_solutions/vmware-esxi-5_Reference%20Guide6_en-us.pdf

  This is the same version that he shows for your installation on the R710 so that seems correct.

• Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

  Hi all

  Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.

  Thanks in advance!

  Lee

  Hi Lee,.

  The long wait has its result.

  Seems that it's a typo. Engineering has responded that it is supported.

  Let me know if you encounter other problems.

• Driver RAID for Vmware ESXi 5.1 on Dell R420.

  My project is to install Vmware ESXi 5.1 on a Dell R420 with Raid1 configuration. The question I have after configuring raid1 in raid utility is created using the, I launch the installation of Vmware ESXi 5.1. What is ESXi 5.1 sees not the raid1 partition but rather see two disks as are they worn can't in raid1 configurations.

  I need to have this in raid1 config, can any who share an idea about my problem please or point me in the right direction.

  I did some research but nothing seems to help resolve this issue.

  Thank you

  Sheriff.

  Sorry for my previous response:

  DELL-Daniel My - when I boot in the BIOS of the controller, I see the raid in a raid1 configuration.

  Mgr dev you are right, I did research more when you all answered. I see the PERC S110 pilot was a software raid controller and thus the vmware esxi wouldn't work in a raid configuration 1 (software raid).

  Thank you guys for you answer and who helped me

• VMware ESXi 5.5 - System Board SEL_FULLNESS 0... 100 unknown

  Hello community,

  I'm going to have that kind of alarm on VMware ESXi 5.5 - SEL_FULLNESS system board 0...

  How to solve this problem?

  vmware_logs.PNG

  

  Greetings.

  You want to connect to your MMIC and clear log SALT.

  Fullness SALT refers to full journal SALT is.

  The journal SALT allows only a certain number of entries before becoming full.

  Thank you

  Kirk...

• BB10 Simulator on Vmware ESXi

  I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:

  1. Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
  2. Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.

  At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.

  The next step is to connect the Momentics IDE to this virtual machine.

  The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.

  If I try to connect to the virtual machine by IP address, I need a device password, I did not.

  Someone at - it suggestions on what do I do now?

  In response to my own question because I found the answer:

  Now that I have the IP address, I just follow the steps described in

  http://supportforums.BlackBerry.com/T5/native-development/BB10-native-Cascades-SDK-not-connecting-to...

  Because I had never set up a password for the Simulator, I left the empty password field.

  Copy-paste the details:

  Of your IDE

  -Right click on your project in the Project Explorer

  -Go to Blackberry tools and click on configure target...

  -Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish

  To run your application on the Simulator:

  -In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.

  -Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.

  -In the Project Explorer view, right-click the project and select build project.

  -Right click on the project again, and then select run as > BlackBerry Application C/C++.

• To install Vmware Esxi 4 on PowerEdge 2800

  Hello. I have a PowerEdge 2800. I wanted to install Esxi 4.

  I download the OM_6.5.0_SMTD_A0.iso and the server starts on the DVD. When I choose install Vmware Esxi 4.0, it asks me to insert the CD / DVD with. But when I insert the DVD the Vmware I download refuses to recognize. Please help me solve the problem. I even tried to install windows server 2008, he refuses.

  Tank you.

  I saw the solution.

  I was supposed to download "VMware-VMvisor-install". Dell_Customized.ISO' to 'http://ftp.dell.com/esg%20solutions/ '.

  Tank you.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.