VMware ESXi monitoring

Similar Questions

• OpenManage for VMWare ESXi has no possibility of tasks of virtual disk

  OMSA v 7.1 and 7.2 for Windows (and earlier versions) allow the user to perform many tasks on virtual disks, including reconfiguring - expand a RAID array with a new drive.

  This is not true for managing open for VMWare ESXi - although you can monitor the status of the RAID and disks with the browser of the OMSA interface type, you cannot perform tasks - can not even make a high beam Flash.

  It is a huge problem, because the PERC controllers (H700 and H800, for example) don't allow you to develop virtual using hard drives not Dell disks when you try this during startup in the bios.  (These controllers only allows you to create new virtual disks using drives not Dell).

  This test was conducted using the latest firmware (12.10.4 - 0001 A10) and drivers for the H700 and H800 and multi-server r610 ESXi 5.1.

  Other people with VMWare have been affected by the present?  The only solution is to have two player networks connected to the computer, and create a simple Windows with OMSA, boot in Windows Server to expand the table using OMSA for Windows.

  I would be interested in the comments of others, including those of Dell.  We spent hours on the phone with Dell; This seems to be the only solution.  (Yes, Dell released a firmware version last year that has ceased blocking non Dell readers, but it only works for the creation of a new virtual disk, do not expanding one existing).

  Yes.  It came through a discussion in the Dell | Servers | Discussion of the RAID community.

  en.Community.Dell.com/.../20263442.aspx

  There is a CD bootable linux called OMSA Live that you download from PowerEdge (linux OS) systems management.

  This OMSA PERC H700 and H800 control and allows you to do everything.  When you reconfigure the RAID and the PERC card starts the reconstruction, although it seems risky, you can restart under VMware and the reconstruction of the RAID continues on.  And you can analyze with OMSA for VMware.

• LSI MegaRAID Storage Manager on VMware ESXi 4.0

  Hi guys,.

  We tried to install on VMware ESXi 4.0 MegaRAID Storage Manager (IBM x 3550 M2) and it uses Controller RAID MegaRAID SAS 8808E to monitor the hard disk status but could not be able to install and it returned the error as attaché

  We followed the procedure as shown in the following ibm Web site

  1.6 MegaRAID Manager storage system to a VMWare ESX Server

  Follow these steps to install the on a MegaRAID Storage Manager

  VMWare ESX Server:

  1. download the latest MSM to ibm.com

  2 unzip the and copy MSM_linux_installer - 501.01.tar.gz on a USB key.

  3. from the ESX Server, in the console root, type the following command

  to identify the USB device: fdisk-l

  4. type the following command: mount/mnt/dev / {name of the USB device}

  5. type the following command: cd/mnt

  6. type the following command to copy MSM_linux_installer - 501.01.tar.gz in the occupied Palestinian territories

  file: cp MSM_linux_installer - 501.01.tar.gz / opt

  7. type the following command to decompress the package gunzip MSM_linux_installer - 501.01.tar.gz

  8 type the following command to unzip the package tar - vxf MSM_linux_installer - 501.01.tar

  9. replace the directories with the path/opt/disk

  10 tapez./vmware_install.sh to install MSM

  11. Select version of VMware

  a. enter 1 to install Vmware 3.5

  b enter 2 for VMware 4.0 install

  12. Select the storlib option

  a. Enter n If you want to use the Inbox storlib driver

  b. Enter y if you want to install the storlib delivered with MSM

  IBM recommends 'y' is selected for use packed with MSM, storlib by selecting "n" can

  cause some features of MSM does not function properly

  I would like to know if I use the correct version of the Storage Manager Application MegaRAID for VMware ESXi 4.0

  
  

  If not could someone please advise on how to proceed with the installation and troubleshooting

  Please find the file of errors as attaché

  
  

  Greatly appreciate your help

  
  

  Thanks in advance,

  Vignesh
  

  Check if help: vSphere unknown health status ' vSphere ' eMware »»

• CONFIG for VMWARE ESXi 5.1 LABORATORY home

  Hello

  Is below configuration good enough to set up the VMware ESXi 5.1 laboratory at home?

  
  

  CPU - Intel® Core™ i7-4770 processor (8 M Cache, up to 3.90 GHz)

  Motherboard - Intel DQ87PG

  SAS hard drive - SEAGATE BARRACUDor

  SEAGATE BARRACUDA 7200.14 hard drive - 1 TB

  Hard drive SSD - Samsung 840 Evo 120 GB

  Memory (16 GB) - Kingston DDR3 1600 MHz 8 GB * 2

  Monitor - SAMSUNG S19A003N

  Cabinet - battle of Cooler Master HAF 912

  OS - Windows 7 Professional 64 bit

  
  

  I intend to return one of the below links to set up the LAB and I hope the above configuration is in favour.

  
  

  http://boerlowie.WordPress.com/2011/11/30/building-the-ultimate-vSphere-lab-part-1-the-story/

  
  

  or

  http://popravak.WordPress.com/2013/07/26/VMware-vSphere-5-1-lab-on-our-laptops/

  
  

  
  

  Thank you

  
  

  You can find all downloads for VMwre to https://my.vmware.com/web/vmware/downloads. What you might want to look for are the links "Download trial" to "VMware Workstation" and "VMware vSphere. BTW. is there a reason you ask for older versions?

  For Windows Server, see download Windows Server 2008 R2 Evaluation (180 days) from the official Microsoft Download Center

  André

  PS: In the past VMware has provided a free license of VMware Workstation after you have completed the requirements to become a VCP - DCV (i.e. necessary training, more exam). I'm sure they'll continue to do that.

• VMware ESXi 4.0 startup screen Purple: 14 Exception PF world 9154?

  Hello

  I'm a VMware ESXi start purple screen: 14 Exception PF world 9154.

  This server running exchange 2010 on vmware esxi 4.0.0 update 2 on an HP DL180 G6 server.

  I downloaded and installed year HP ESXi Offline Bundle for VMware ESXi 4.0 Update 2 patch to be able to monitor this server from my HP System Insight Manager server (which monitors all servers) (http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 5351 & prodSeriesId = 1121516 & swItem = MTX-7ba9a9031d7e4a41ad65f038e0 & prodNameId = 3288134 & swEnvOID = 4040 & swLang = 8 & taskId = 135 & mode = 4 & idx = 1).

  The hotfix installation completed successfully. However, after that I restarted ESXi, I started getting this error PF Exception 14 with a bunch of numbers and codes.

  At this stage I don't know how I can fix. Any help will be grateful!

  Thank you

  Luis

  In the meantime you can restore the previous version before upgrading. Press
  SHIFT + R when you get the hypervisor loading screen. You will be asked to OK rollback.

• Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0

  Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.

  On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?

  Hello

  You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter

• R710/R720 - Dell customized Image of VMware ESXi 5.5 Update 2 - megaraid_sas version specific?

  That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:

  www.dell.com/.../DriversDetails

  The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:

  www.Dell.com/.../manuals

  indicates that a specific version of the megaraid_sas driver must be installed.

  Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?

  I just ran the upgrade on a R710 and it's the megaraid_sas version installed:

  ~ # vmkload_mod s megaraid_sas | grep Version
  Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014

  Thank you.

  Hello

  It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02

  megaraid_sas - 06.803.73.00

  Page 5 ftp://ftp.dell.com/Manuals/all-products/esuprt_software/esuprt_virt_solutions/vmware-esxi-5_Reference%20Guide6_en-us.pdf

  This is the same version that he shows for your installation on the R710 so that seems correct.

• Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

  Hi all

  Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.

  Thanks in advance!

  Lee

  Hi Lee,.

  The long wait has its result.

  Seems that it's a typo. Engineering has responded that it is supported.

  Let me know if you encounter other problems.

• Driver RAID for Vmware ESXi 5.1 on Dell R420.

  My project is to install Vmware ESXi 5.1 on a Dell R420 with Raid1 configuration. The question I have after configuring raid1 in raid utility is created using the, I launch the installation of Vmware ESXi 5.1. What is ESXi 5.1 sees not the raid1 partition but rather see two disks as are they worn can't in raid1 configurations.

  I need to have this in raid1 config, can any who share an idea about my problem please or point me in the right direction.

  I did some research but nothing seems to help resolve this issue.

  Thank you

  Sheriff.

  Sorry for my previous response:

  DELL-Daniel My - when I boot in the BIOS of the controller, I see the raid in a raid1 configuration.

  Mgr dev you are right, I did research more when you all answered. I see the PERC S110 pilot was a software raid controller and thus the vmware esxi wouldn't work in a raid configuration 1 (software raid).

  Thank you guys for you answer and who helped me

• VMware ESXi 5.5 - System Board SEL_FULLNESS 0... 100 unknown

  Hello community,

  I'm going to have that kind of alarm on VMware ESXi 5.5 - SEL_FULLNESS system board 0...

  How to solve this problem?

  vmware_logs.PNG

  

  Greetings.

  You want to connect to your MMIC and clear log SALT.

  Fullness SALT refers to full journal SALT is.

  The journal SALT allows only a certain number of entries before becoming full.

  Thank you

  Kirk...

• BB10 Simulator on Vmware ESXi

  I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:

  1. Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
  2. Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.

  At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.

  The next step is to connect the Momentics IDE to this virtual machine.

  The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.

  If I try to connect to the virtual machine by IP address, I need a device password, I did not.

  Someone at - it suggestions on what do I do now?

  In response to my own question because I found the answer:

  Now that I have the IP address, I just follow the steps described in

  http://supportforums.BlackBerry.com/T5/native-development/BB10-native-Cascades-SDK-not-connecting-to...

  Because I had never set up a password for the Simulator, I left the empty password field.

  Copy-paste the details:

  Of your IDE

  -Right click on your project in the Project Explorer

  -Go to Blackberry tools and click on configure target...

  -Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish

  To run your application on the Simulator:

  -In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.

  -Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.

  -In the Project Explorer view, right-click the project and select build project.

  -Right click on the project again, and then select run as > BlackBerry Application C/C++.

• To install Vmware Esxi 4 on PowerEdge 2800

  Hello. I have a PowerEdge 2800. I wanted to install Esxi 4.

  I download the OM_6.5.0_SMTD_A0.iso and the server starts on the DVD. When I choose install Vmware Esxi 4.0, it asks me to insert the CD / DVD with. But when I insert the DVD the Vmware I download refuses to recognize. Please help me solve the problem. I even tried to install windows server 2008, he refuses.

  Tank you.

  I saw the solution.

  I was supposed to download "VMware-VMvisor-install". Dell_Customized.ISO' to 'http://ftp.dell.com/esg%20solutions/ '.

  Tank you.

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC.

  I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC. also, I am unable to ping the address IP of CIMC. Any help?

  I think that MMIC does nothing with your ESXi installation... it is OoB management for servers of the UCS.

  Check your config MMIC inside the BIOS again.

  BR,

  Dragan