VPN client works not

Similar Questions

• AnyConnect VPN Client - works with IPsec

  Hello

  How can I do for AnyConnect VPN Client works with ipsec?

  I tried with SSL and works normally.

  But with IPsec does not work. Should I do something?

  Thank you

  Rodrigo

  Rodrigo, Anyconnect works with SSL, in order to use IPSec, you must the Cisco VPN Client.

• 'Connected' but 5.0.07.0440 VPN client does not work

  Hello

  IMPORTANT THING I FORGOT: the customer seems to be connected. It shows a lock locked and says connected but ping shows that nothing is not working too.

  I recently tried, in vain, to connect my win7 64 bit laptop to my place of work with the Client VPN 5.0.07.0440. All technitians and support staff could not understand the problem that prevented successful login. Later, I could connect my laptop using the VPN Client 5.0.07.0410 - same home network via an old k9, winXP.

  What could be the problem with Win7 system? Work on my old laptop is a temporary solution, but not a good thing. I would be grateful for all the help I can get.

  I tried:

  -For each access to the Cisco VPN client on my ZoneAlarm firewall.

  -Turning off the firewall completely.

  -Connect to a different network (in an Internet Café).

  Personal support at work said this isn't the network (they checked my too just in case wifi router settings) from my old computer obviously connects without any problem on the first try.

  ANY ideas would be very appreciated!

  Here is the info yet:

  -Cisco VPN Client 5.0.07.0440

  -64-bit Windows 7 Home Premium SP 1.

  My security software (which may cause the problem as far as I know, even if I close ZoneAlarm):

  -Free firewall zone alarm

  -Microsoft Security Essentials.

  (maybe windows firewall too, if it automatically restarts when I turned off zone alarm)

  IMPORTANT THING I FORGOT: the customer seems to be connected. It shows a lock locked and says connected but ping shows that nothing is not working too.

  Hello

  VPN client traffic is not transmitted from your computer to the VPN at all tunnel.

  It's if you have even tried the connection to the remote server before you took this screenshot?

  ID say it is a problem with your computer. Some software cause problems for the VPN Client or Client VPN software has problems with the network card real or something similar.

  One thing I might suggest is uninstall the firewall software and the VPN Client. After that, it is enough to install the VPN Client and try to login and check the statistics of same as in the pictures above.

  -Jouni

  EDIT: Whoa 300 posts already

  Edit2: If you have a full VPN tunnel, your computer must usually generate connections to the VPN tunnel even if you do not manually connect what either. What makes it even more strange that there are absolutely no traffic in the tunnel. Full VPN tunnel means that all traffic from your computer is transferred to the VPN tunnel when his assets.

• VPN client works well, but I am not able to open the desktop remotely

  Hi all

  I configured a router 877 with features of firewall and VPN and DDNS, when the user connects his WAN pc via VPN all works well (mail, telnet, ping, LAN access) but the Remote Desktop feature is not available. I traced with wireshark and saw that the request to port 3389 was correctly sent to the destination server, but the response to the VPN client has been abandoned by the router... and I have no idea how to solve this problem.

  Can someone help me...? Thank you very much.

  Ilaria.

  In room router attached.

  Your problem is the NAT-config. First of all, the next line is not necessary that RDP does not have UDP ober:

  IP nat inside source static udp 192.168.10.136 3389 3389 Dialer0 interface

  Then, the following command causes problems:

  IP nat inside source static tcp 192.168.10.136 3389 3389 Dialer0 interface

  With which the router assumes that the server 192.168.10.136 must always be reached through the IP address of dialer0 and made a translation.

  There are two ways to solve the problem, but they all have some disadvantages...

  (1) only access the server through VPN. For that you can just remove the NAT statement above (the one with tcp) and you should be able to reach the server via VPN.

  (2) restrict the NAT for not doing a translation if a VPN-peer's access to the server.

  To do this, you must attach a roadmap to the NAT statement. But who does not work with the "interface" - keyword in the NAT Statement. But you can use it if you get a fixed IP address from your provider.

  (3) assign a second IP address to the RDP server. The period of the original INVESTIGATION that is used in the NAT statement is used to access the server without VPN, the second IP address is used to access the server through VPN.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• SonicWALL VPN Client does not connect

  I use Windows 10 Pro.  I can install the NEW Client VPN (4.9.0.2012) very well.  When I put in information that works very well.  It will even connected, the first time, when you have completed the installation.  Here's the crazy part.  I can't disable the VPN client.  When I try to ACTIVATE the connection he wants to use a telephone line.  I can uninstall the client software and tell him NOT to keep data.  I can reinstall the client and it will connect the first time.  After that it will not.  I have already told him to use LAN ONLY entered in the network settings.  Only, it crashes and then trying to acquire IP.

  Norman

  I think you are talking about the Global VPN Client. You must uninstall this version of CVM and install the most recent of 4.9.4.0306 which has been validated to run on Windows 10.

  #Iwork4Dell

• Windows - Internet access, no split Tunnel L2TP VPN Clients does not

  Greetings!

  I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

  I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

  Here is the configuration:

  : Saved
  :
  ASA Version 1.0000 11
  !
  SGC hostname
  domain somewhere.com
  names of
  COMMENTS COMMENTS LAN 192.168.2.0 name description
  name 75.185.129.13 description of SGC - external INTERNAL ASA
  name 172.22.0.0 description of SITE1-LAN Ohio management network
  description of SITE2-LAN name 172.23.0.0 Lake Club Network
  name 172.24.0.0 description of training3-LAN network Southwood
  description of training3 - ASA 123.234.8.124 ASA Southwoods name
  INTERNAL name 192.168.10.0 network Local INTERNAL description
  description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
  description of Apollo name 192.168.10.4 INTERNAL domain controller
  description of DHD name 192.168.10.2 Access Point #1
  description of GDO name 192.168.10.3 Access Point #2
  description of Odyssey name 192.168.10.5 INTERNAL Test Server
  CMS internal description INTERNAL ASA name 192.168.10.1
  name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
  description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
  description of training3-VOICE name Southwood Voice Network 10.1.0.0
  name 172.25.0.0 description of training3-WIFI wireless Southwood
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan2
  nameif INSIDE
  security-level 100
  255.255.255.0 SGC-internal IP address
  !
  interface Vlan3
  nameif COMMENTS
  security-level 50
  IP 192.168.2.1 255.255.255.0
  !
  interface Ethernet0/0
  Time Warner Cable description
  !
  interface Ethernet0/1
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/2
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/3
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/4
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/5
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/6
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/7
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  boot system Disk0: / asa821-11 - k8.bin
  Disk0: / config.txt boot configuration
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS domain-lookup outside
  INTERNAL DNS domain-lookup
  DNS domain-lookup GUEST
  DNS server-group DefaultDNS
  Name-Server 4.2.2.2
  domain somewhere.com
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  DM_INLINE_TCP_1 tcp service object-group
  EQ port 3389 object
  port-object eq www
  EQ object of the https port
  EQ smtp port object
  the DM_INLINE_NETWORK_1 object-group network
  network-object SITE1-LAN 255.255.0.0
  network-object SITE2-LAN 255.255.0.0
  network-object training3-LAN 255.255.0.0
  object-group training3-GLOBAL network
  Southwood description Global Network
  network-object training3-LAN 255.255.0.0
  network-object training3-VOICE 255.255.0.0
  network-object training3-WIFI 255.255.0.0
  DM_INLINE_TCP_2 tcp service object-group
  EQ port 5900 object
  EQ object Port 5901
  object-group network INTERNAL GLOBAL
  Description Global INTERNAL Network
  network-object INTERNAL 255.255.255.0
  network-object INTERNALLY-VPN 255.255.255.0
  access-list outside_access note Pings allow
  outside_access list extended access permit icmp any CMS-external host
  access-list outside_access note that VNC for Camille
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
  access-list outside_access note INTERNAL Services
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
  DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
  access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  no pager
  Enable logging
  exploitation forest asdm warnings
  Debugging trace record
  Outside 1500 MTU
  MTU 1500 INTERNAL
  MTU 1500 COMMENTS
  192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  enable ASDM history
  ARP timeout 14400
  Global 1 interface (outside)
  (INTERNAL) NAT 0 access-list sheep
  NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
  NAT (GUEST) 1 0.0.0.0 0.0.0.0
  5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
  public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
  5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  Access-group outside_access in interface outside
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server Apollo
  Apollo (INTERNAL) AAA-server Apollo
  Timeout 5
  key *.
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  Enable http server
  http 0.0.0.0 0.0.0.0 INTERNAL
  http 0.0.0.0 0.0.0.0 COMMENTS
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
  correspondence address 1 card crypto outside_map INTERNAL SITE1
  card crypto outside_map 1 set of peer SITE1 - ASA
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  address for correspondence card crypto outside_map 2 INTERNAL training3
  outside_map 2 peer training3 - ASA crypto card game
  card crypto outside_map 2 game of transformation-ESP-3DES-SHA
  address for correspondence outside_map 3 card crypto INTERNAL SITE2
  game card crypto outside_map 3 peers SITE2 - ASA
  card crypto outside_map 3 game of transformation-ESP-3DES-SHA
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  delimiter group @.
  Telnet training3 - ASA 255.255.255.255 outside
  Telnet SITE2 - ASA 255.255.255.255 outside
  Telnet SITE1 - ASA 255.255.255.255 outside
  Telnet 0.0.0.0 0.0.0.0 INTERNAL
  Telnet 0.0.0.0 0.0.0.0 COMMENTS
  Telnet timeout 60
  SSH enable ibou
  SSH training3 - ASA 255.255.255.255 outside
  SSH SITE2 - ASA 255.255.255.255 outside
  SSH SITE1 - ASA 255.255.255.255 outside
  SSH 0.0.0.0 0.0.0.0 INTERNAL
  SSH 0.0.0.0 0.0.0.0 COMMENTS
  SSH timeout 60
  Console timeout 0
  access to the INTERNAL administration
  Hello to tunnel L2TP 100
  interface ID client DHCP-client to the outside
  dhcpd dns 4.2.2.1 4.2.2.2
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  !
  address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
  dhcpd Apollo Odyssey interface INTERNAL dns
  dhcpd somewhere.com domain INTERNAL interface
  interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
  enable dhcpd INTERNAL
  !
  dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
  dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
  enable dhcpd COMMENTS
  !

  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 192.43.244.18 prefer external source
  WebVPN
  allow outside
  CSD image disk0:/securedesktop-asa-3.4.2048.pkg
  SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
  enable SVC
  Group Policy DefaultRAGroup INTERNAL
  attributes of Group Policy DefaultRAGroup
  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  Group Policy DefaultWEBVPNGroup INTERNAL
  attributes of Group Policy DefaultWEBVPNGroup
  VPN-tunnel-Protocol webvpn
  Group Policy DefaultL2LGroup INTERNAL
  attributes of Group Policy DefaultL2LGroup
  Protocol-tunnel-VPN IPSec l2tp ipsec
  Group Policy DefaultACVPNGroup INTERNAL
  attributes of Group Policy DefaultACVPNGroup
  VPN-tunnel-Protocol svc
  attributes of Group Policy DfltGrpPolicy
  value of 192.168.10.4 DNS Server 4.2.2.2
  VPN - 25 simultaneous connections
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  the value INTERNAL VPN address pools
  chip-removal-disconnect disable card
  WebVPN
  SVC keepalive no
  client of dpd-interval SVC no
  dpd-interval SVC bridge no
  value of customization DfltCustomization
  attributes global-tunnel-group DefaultRAGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultRAGroup
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  Disable ISAKMP keepalive
  tunnel-group DefaultRAGroup ppp-attributes
  No chap authentication
  no authentication ms-chap-v1
  ms-chap-v2 authentication
  attributes global-tunnel-group DefaultWEBVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultWEBVPNGroup
  tunnel-group 123.234.8.60 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.60
  pre-shared-key *.
  tunnel-group 123.234.8.124 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.124
  pre-shared-key *.
  tunnel-group 123.234.8.189 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.189
  pre-shared-key *.
  type tunnel-group DefaultACVPNGroup remote access
  attributes global-tunnel-group DefaultACVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultACVPNGroup
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the http
  inspect the they
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
  : end
  ASDM image disk0: / asdm - 623.bin
  ASDM location Camille 255.255.255.255 INTERNAL
  ASDM location INTERNAL CGT-external 255.255.255.255
  ASDM location INTERNAL SITE1-LAN 255.255.0.0
  ASDM location INTERNAL SITE2-LAN 255.255.0.0
  ASDM location INTERNAL training3-LAN 255.255.0.0
  ASDM location INTERNAL training3 - ASA 255.255.255.255
  ASDM location INTERNAL GDO 255.255.255.255
  ASDM location INTERNAL SITE1 - ASA 255.255.255.255
  ASDM location INTERNAL SITE2 - ASA 255.255.255.255
  ASDM location INTERNAL training3-VOICE 255.255.0.0
  ASDM location puppy 255.255.255.255 INTERNAL
  enable ASDM history

  I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

  You must configure * intercept-dhcp enable * in your group strategy:

  attributes of Group Policy DefaultRAGroup

  attributes of Group Policy DefaultRAGroup

  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com

  Intercept-dhcp enable

  -Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked.  It is located on the Advanced tab of VPN client TCP/IP properties.   Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

  Alex

• IP address of the IPSec VPN client did not get distributed via EIGRP

  We use an ASA for VPN remote access. He is running EIGRP redistribute static routes. When a client Anyconnect SSL connects, the SAA creates a static route for this client, and it gets redistributed via EIGRP. When an IPSec VPN client connects, the SAA creates a static route for this customer, but he isn't redisributed via EIGRP and so the client can not achieve anything. Why he would distribute a static created by an IPSec client?

  Thank you

  Have you set up IPP on dynamic Cryptography?

• The VPN Clients do not directly see Conencted network

  Hello - I have a Pix 515 that I use for the VPN. Everything works, except when it is docked, (172.16.3.0) clients cannot see directly connected network (192.168.2.0) and not one of our other subnets. What is missing?

  Andy,

  The SAA on the inside of the IP subnet is 192.168.2.0/24 - but you have no roads to indicate that any other subnets of the 192.168.0.0/16 is. If you have several subnets within the network, you will need to do ASA know about them, for example: -.

  Route inside 192.168.1.0 255.255.255.0<>

  You should also decided if you go to any traffic or split tunnel.

  HTH >

• SonicWALL NSA, using VPN client overall comments to reach network of internal resources

  Hello

  I have problems performing Global VPN client to work when you connect to our internal network of comments in order to reach our internal LAN Server in order to reach internal resources in a safe manner. I'm not sure what could the settings were necessary in the Sonicwall to achieve?

  Our installation is based on the NSA 3600 and I installed a WLAN area in the sonicwall to enable clients to connect to the internet. Traffic in the WLAN area to our internal LAN Server is denied. However, some users would like to be able to use the wireless network in order to achieve internal resources and for that I want to use the Global VPN client. It is even possible to use of an internal network from the point of view Sonicwalls Global VPN client?

  The use of the outside Global VPN client works very well

  Any help is greatly appreciated and if more detailed configuration information are necessary, I'll happily give you that.

  Thank you

  Hi Ben,

  No I didn't at first, but your answers have would lead me in the right direction, hopefully. I realized that I could create a custom GroupVPN by going to the settings of the interface to the interface that is the war in the Gulf to my wireless network.

  return to results

  Thank you

  Cree

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• Allow Cisco VPN Client through the firewall?

  Hello

  How can I allow a cisco VPN client work from the inside of our network to an external IP address?

  We have customers who wish to make use of their Cisco VPN Client companies but our ASA blocks I think?

  Also (sorry to ask) a friend in South America is having the same problem but I am not hink they use Cisco, is there a default port used by the client to Cisco? then I can send this info?

  Thank you

  Generally, the ASA will allow the IPSEC from the inside to outside traffic. This is when you want it came outside and connect to you - this is where it gets creative. You restrict outgoing traffic at all? You deny all ip/tcp/udp outgoing?

  But may depend on if the remote end is compaitable NAT - T, and if they have configured. Another question would be how they allow VPN traffic go?

• Need help with native VPN client for Mac to the Configuration of the VPN router RV082

  Guys,

  I am trying to set up router RV082 VPN Client with native Mac for my remote access. However, no matter what I did, I'm not able to make works. Can any give me an example of how to set my router RV082 and Mac Book Pro (Mountain Lion)?

  Thank you

  Hi Jixian, the native client MAC does not work. The IPSEC VPN client is the same as the 5.x Cisco VPN client is not supported on this device.

  Your alternatives are to use PPTP or a 3rd party IPsec client such as ipsecuritas.

  -Tom
  Please evaluate the useful messages

• VPN client: What ports and protocols?

  Anyone know which ports and protocols are used by the cisco VPN client? (Telco needs this info, because the VPN client does not work in its network)

  I know of UDP/500 (ISAKMP)

  Erik

  Erik,

  In addition to ISAKMP, Protocol ESP 50 you and, possibly, NAT - T which is UDP/4500.

  Andy

• VPN client and peer simultaneously with dynamic ip

  LAN (static ip) - to - Lan (static ip) is very well

  LAN (static ip) - to - Lan(static ip) + VPN Client is fine

  LAN (static ip) - to - Lan (dynamic ip) is very well

  LAN (static ip) - to - Client VPN is good

  LAN (static ip) - to - Lan(dynamic ip) + VPN Client does not work

  I think that the problem is due to this commans

  ISAKMP crypto keyname key address 0.0.0.0 0.0.0.0

  or

  ISAKMP crypto keyname key address 0.0.0.0 0.0.0.0 no.-xauth

  How can I distinguish a router with a dynamic ip address that doesn't require authentication from a VPN Client that requires authentication?

  P.D. I use local authentication

  You are right in your diagnosys of the problem, we see this from time to time and there is not much that can be done unfortunately.

  The only way is if the remote peer Gets a subnet or a dynamic address on a particular beach all the time, then add a line "isakmp key... No.-xauth" with this defined subnet. For example, if the remote peer always receives an address in 4.104.225.0/24, then do:

  > cry isa key address 4.104.225.0 255.255.255.0 no.-xauth

  Not much, but it's the only way around it.