Xbox connected to the HDMI port, the only problem being transmitted through the built-in speakers is extremely strong, o change the volume but not succession

Similar Questions

• Computer connects to the network, but not to the Internet, connect to the only local

  Hello world

  OK, so I have a HP computer with the installed version of Windows Vista Home Premium 32-bit. I've had it for almost 2 years now and have had no problems connecting to Internet... until now.

  I can connect to networks... both wireless and cable, but I can not get Internet. I used the IP, subnet mask, gateway and server settings DNS to another computer that works with this specific local network just to see what happens... my computer has failed.
  Until recently, I could connect to this WiFi connection in a coffee shop, but the last time I tried it didn't work. I've connected to the network but not the Internet. He told me that the DNS server did not. I'm starting to think that something is wrong with my computer.

  I saw that the solution for some people running the Norton removal tool, however I had uninstalled Norton almost as soon as I got my computer 2 years ago and ran McAfee instead. I don't think that Norton should have an impact on me more.

  Is there a solution to this problem... or I'll just have to try everything that is out there?

  Thanks for your help!

  Hi MomPlaysBass,

  Finally, my problem has been resolved - it wasn't my computer after all. The modem may only be connected to a computer. If you want to connect to another computer, you can connect the computer to the modem and then put it back. My computer worked fine after that. Whenever we want to switch between computers, even if I have to reset the modem.

  I don't think you have the same problem, but just in case, you can try to reset your modem - it's a button on the back or a small hole that you can reach with a pen... Hold the stylus for about 5 sec or maybe a bit more and then let go. That should reset your modem and might help you with your problem. Your computer should also have created a restore point... If all else fails maybe you can try to get back to the final point where your computer worked.

• WRTG54S to connect to the network, but not internet

  I have a WRTG54S and Mediacom 12mbps. My router worked fine on my old laptop (a Dell Vista), he was sitting in a box for about 6 months and now that I have a new (Sony running 7) I can connect to my network, but not internet. I have updated the firmware of 7.6 to 7.8 without change. I have tried no security, wep and wap without change. Also, I cloned the MAC, once again no change. Windows cannot detect all problems, and when I try to activate the router to connect to the internet it always says connection failed. I can connect directly connected to the modem but not when connected to the router or wireless. Any ideas? Thank you

  Problem solved. I had to go to a Motorola SurfBoard 4100 to a 5100. Thanks anyway

• Devices to connect to the airport, but not to the Internet

  Hi all; Here's my situation:

  I just bought a new Airport Extreme to replace my old router (Linksys). In our House, we have two iPhones 6, as well as the iPad, Apple TV and MacBook Pro that were all bought again this year. All these things were able to connect to the internet using our old wireless router.

  As I have configured and installed at the airport, various devices have been able to connect without being able to connect to the internet (i.e. AirPort Utility, the airport connection is a green dot, while the actual internet connection is an orange): first it was the MacBook having this problem while the phones and the iPad have been completely connected. After I simply rebooted everything several times - i.e. the modem, router, and MacBook - I finally got the MacBook fully connected (without really changing all the settings, which are all entered correctly). Now, however, it is the two iPhones that will connect the airport but not actually in the internet.

  Any ideas? I must say, these strange little problems idiopathic who seem to always pop up with Apple products are starting to really bother me... I never got my MacBook to connect to the Apple TV via AirPlay.

  Any time you change the material or providers of Internet services, networking, it's always a good idea to perform a complete recycling of your network equipment power. Check out the following Tip of an airport users for more details on how to do it. Please post back your results.

• Laptop HP G70 connection to the router but not the internet

  I have a laptop HP G70 running windows 7, I got a new router installed. My computer to the router, but not to the internet links. I tried the software updates for my drivers running, doing all used to end router for example change etc channel/parameters/IP wifi. I tried to turn off the wireless, reset the router and re enabling it does not work.

  It will connect to the internet ethernet of nis.

  My laptop connects fine with other networks if it is not wireless.

  All other devices are connected to the router.

  Please help this is extremely frustrating.

  You are the very welcome.

  I compressed the file and downloaded on my Skydrive account, which I shared the link below.

  Download, unzip and run the file called sp54972.

  https://onedrive.live.com/redir?RESID=832F4957D2E51B93! 263 & authkey =! AEOhdjA3QVhETy0 & ithint = % 2czip

• Canon PIXMA MG5220 Photo-All - in - One Printer - my printer print when connected to the computer, but not when it is wireless

  Window indicates that my new printer Canon PIXMA MG5220 Photo All in One Printer is compatible with my Dell Inspiron E1705, my printer prints so that connected to the computer but when I try to print wireless, it does not work. The printer is wireless and I have a wireless cable modem, what am I I lack to the printer wireless?  Please advise.

  Hi LouiseFarmer,

  It seems there is a problem in the basic WIFI the printer setting.

  I suggest you show the manufacturer's Web site to learn more about the drivers and the printer setting to print via WIFI.

  http://USA.Canon.com/Cusa/consumer/products/printers_multifunction/photo_all_in_one_inkjet_printers/pixma_mg5220#MiscWirelessHelp

• Can connect to the network, but not the internet, a "Local" access only

  Just installed a new router and am now unable to connect to internet on my HP laptop. The laptop is running Windows Vista 64-bit Service pack 1. Pulling him diagnose & repair window returns a message indicating "your modem or router is not available.

  I tried several things to get the internet to connect. I have reinstalled the driver, turned off the firewall, disabled the Internet Version 6 (TCP/IPv6) Protocol and manually configure the network connection.

  I have a desktop computer with a wireless adapater that performs the exact same OS as the laptop and I have no problem with this connection.

  I am able to connect to the internet if I connect the laptop to the ethernet cable. I am completely confused and would appreciate any advice!

  Hi Ima be,

  You can follow the steps below and check if that helps you solve the problem.

  Method 1

  Try to power cycle the router and the computer and check if it helps.

  On the PC:

  1. Save your work and restart the machine.

  On the router or modem (if wireless printing):

  1. Unplug the router and the modem.
  2. Wait 30 seconds.
  3. Plug in the modem and wait for it to come to the ready state.
  4. Plug in the router.

  After you put cycle check the connection between the router and the computer.

  Method 2

  If the steps above do not help, you mayreset TCP/IP stack. To reset access the link below and either click on "Fix it for me" or follow the instructions to fix it yourself:http://support.microsoft.com/kb/299357
   
  Disable the IP helpdesk:
  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter
  2. scroll down to the IP assistance service, right-click on it and select Properties
  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.
  4. then click on "Stop" to stop the service from running in the current session
  5. click on OK to exit the dialog box

  Method 3

  Disable IPv6 and remove IPv6 virtual cards:
   
  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection, even if they are disabled.

  Method 4

  Disable the DHCP Broadcast Flag:
  Link: http://support.microsoft.com/default.aspx/kb/928233
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.microsoft.com/kb/322756.  How to back up and restore the registry in Windows
   
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
   
  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:
  1. Click Start, type regedit in the search box, and then click regedit in the list programs.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  3. Locate and then click the following registry subkey:
  4 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}
  5. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  6. on the Edit menu, point to new, and then click DWORD (32-bit) value.
  7. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.
  8. right click on DhcpConnEnableBcastFlagToggle, then click on modify.
  9. in the value data box, type 1 and then click OK.
  10. close the registry editor.
   
  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.
  You can also try uninstalling and reinstalling the driver for the wireless card.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Logical remote connects to the MainStage but not Garageband?

  I have tried everything I can find to do remote logic to connect to the Garage band and none of it works.

  I can get my iPad to connect to MainStage without any problem. Open the first time I run logic remote with Garageband

  I get the prompt to allow the connection and pair the remote but from there it happens just to expire and I get the message...

  'Logic remotely was unable to connect to the selected Mac. If this is the first time that you connect logic remotely, you must confirm the connection on the selected Mac. " I did this step. I have the latest version of MainStage and Garageband available from 26/01/16.

  My firewall settings are turned off completely,

  I removed preference files and rebooted several times.

  I have the same problem between two different Macs and on two different networks.

  Thanks for any help you may have.

  Looks like you are trying to connect to Go with a Pro iPad or iPhone (which is not taken in charge)?  The configuration required for the logic of remote 1.3:

  The system configuration required

  Requires iOS 9.1 or later

  iPad support requires Logic Pro X 10.2.1 MainStage v3.2.3 or GarageBand v10.1

  iPad support Pro requires Logic Pro X 10.2.1 or MainStage v3.2.3

  support iPhone requires Logic Pro X 10.2.1

  Note that GarageBand is currently only supported on iPad.  I expect that will change with the next update to GarageBand, but I don't know about you.

• I can connect to the internet, but not to my home network

  I have a PC running Windows XP SP3, which is connected to a Linksys WRT300N router. I have access to the internet. I can not connect to my home network; don't know what happened. all (3) computers are set to the same workgroup name. I can't find anywhere in the network settings for WinXP that relates my network name. Help!

  Thanks for any help you can provide.

  John

  I guess that the other two computers are working properly and that it can network together and that the only problem is the XP machine.  I'm also assuming that this problem persists when the firewall was disabled (including hidden like the one in the Cisco VPN client).  I also assume you mean by "is no longer connect to my home network" that you can't see other computers in your network neighborhood. See if this article helps you:

  "You can't see the other computers in the workgroup on the network on a Windows XP computer"
    <>http://support.Microsoft.com/kb/903267 >

  If this does not help, try to walk your way through the following:
  "How to troubleshoot network domestic in Windows XP"
    <>http://support.Microsoft.com/kb/308007 >

  HTH,
  JW

• HP 4500 g510n-z-printer connected to the router but not responding do not

  Hello

  I got this printer (HP4500 G510n-z) for 3 years. This worked without any problem until I changed my router and installed a nas on the LAN Server.

  Now the printer is connected via WIFI to router and is perfectly installed on computers connected to the router. But it does not work. I used HP Print-Scan doctor and he finds the device, but it was not connected. I tried to connect to the printer IP of all computers, but I have not received any response (using ping, it doesn't have 75% of the package). On the router configuration page, the printer is connected to the usual IP and on connected computers the TCP - IP is configured correctly.

  I have tried everything and I managed only to reboot the router. But it did not last, each computer remains connected only until you restart the PC nex.

  Sorry if I'm not too clear, please don't exitate ask for more details. Thanks for your help!

  Replacement of your wireless router try now.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

• IPad connects to the wifi but not internet

  I have a new iPad. It connects without problems to my wifi network at home, but when I try to connect to a network in a coffee shop, it shows that it is connected ok, gets an address IP etc, but when I try to use Safari I get a message that it is not connected to the Internet. This has happened in two branches of McDonald's when I tried to use their network. Once a portal connection captive flashed for a moment, but disappeared before I could connect.

  I tried to forget the network and reconnect, a restart of two buttons, reset the network settings, tried to use Google DNS, but none of them have worked for me. My iPhone works without problem on the same network

  Any suggestions on what I can try?

  Vinnie

  Try using another browser. In my experience, sometimes Safari have problems viewing a page ' agree to our conditions "on the hot spots. I have Atomic but there are others out there. Once you connect, Safari will not let you access the conditions page, use the other browser, which should, so you can use whatever one you want to continue browsing.

• My laptop, connect to the network, but not the internet!

  My laptop connects to the network media blank but not internet. My roommates using the network can connect to the internet. I tried various things but not vain. I also tried to get in touch with the Virgin on this subject, but they can help. Is it my laptop and is there something special I need to do with a computer hp laptop. Help, please! Thank you!

  Hello

  On the Start Menu, click programs principally made, click Accessories, right-click on command prompt and select "Run as Administrator".  In the prompt, type the following commands, pressing on enter after each command.  Include spaces in the commands, as indicated.

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int ip reset c:\resetlog.txt

  netsh winsock reset

  Type exit and press ENTER.  Restart the PC and see if you can log in now.

  Kind regards

  DP - K

• Portege R600-101 connects to the WLan but not to the Draft N

  Hi friends...

  I have a Portege R600-101 which is capable of 802.11b/g/n.
  I have now, I tried 2 routers (belkin and Netgear DG834N) to get connected to the speed n machine but no joy... any help greatly appreciated...

  See you soon
  Warren

  Hello!

  Can you connect to the router with the b/g project?

  Maybe the router or laptop computers is not set to the project in order to check the settings in the router and wireless network card.
  In addition, you must disable security as hidden SSID, MAC address filtering and so distant features.

  Good bye

• 2 13 pro tablet of yoga - to connect to the network, but not the internet

  Hello!

  I got my new yoga today and immediately connect it to wifi...

  It connects to my home but not internet network (or connection very very creepy)

  tried home through my phone LTE and still...

  tried by bluetooth and same result... slow as hell... maybe approx. 10 KB.

  im looking good on the web and don't find anything...

  probobly you are the people with the experience...

  help would be appritiated!

  Kind regards.

  Hey guys quick update!

  After sending the lenovo Tablet and a few screams (sad that we cannot otherwise)

  they replace them with sealed brand new...

  so thanks for the help!

• HP Pavilion 2 x 10-N000NA: HP Pavilion x 2 10-N000NA connects to the network, but not to the internet

  Hello

  I have a problem with my HP Pavilion 2 x 10-N000NA Windows 10, 32-bit version...

  I have a router TP-Link W9980 and the laptop connects to the 2.4 GHz network, but there is no internet access.

  However, if I use a range extender (powerline TP-Link Wireless extender), it connects to the network and the internet!

  So, I guess that the equipment is working well, there must be a setting somewhere?

  I've updated all the drivers, etc. for the laptop and the router.

  Any ideas?  Thank you.

  Hello

  Well, the strangest thing happened!

  There was a huge update of Windows, and it seems to have solved the problem.

  Connections now say '(network) secure' or '(network) open' - which they did not before.

  So now that I know that the network was very good and it was a laptop problem which needed fixing.

  However, I do not know what exactly the update fixed, so I can not pass on any knowledge to solve the problem of someone else who suffer.