Yosemite and hp pro 8500 910 and envy 4500

Similar Questions

• HP officejet pro 8500 910 a guard cleaning print head

  HP officejet pro 8500 910 a constantly clean the print head after replacing cartridges inkt (original)

  This happens after each power off/on. I can't stop the process by opening the doors, etc. Could not understand what did the trick.

  The new cartridges are already half empty.

  I did all the configurations, calibration. All the test pages are superb and I still suffer from the issue.

  In this forum, someone (Dutch) had exactly the same problem.

  I hope that someone from HP is able give me some tips.

  Hello there @qtoigoo ,

  I understand that you are facing a problem with your Officejet 8500 continuously clean the print heads. Normally, this occurs if the print heads are going downhill. My best advice to you would be to try clean the contacts on the print heads manually and reset of the printer. Who can help.

  Here is a guide with the relevant instructions: print head issues

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions: click here.

   

  I hope that my post was information!
  

   

  Have a wonderful day
  

• HOW TO REMOVE AND REINSTALL THE OFFICEJET PRO 8500 910 PRINTHEAD

  HP OFFICEJET 8500 910 PRINT HEAD ALIGNMENT FAILED. HOW TO REMOVE & REPLACE THE PRINT HEAD. I READ THE USER GUIDE THAT SAYS LIFT TOP AND THEN LIFT THE PRINTHEAD. UNFORTUNATELY WE YOU SAID NOT HOW TO PROCEED. I OBVIOUSLY DON'T WANT THE LID ON THE GLASS... THE PHOTO SHOWS TOP RAISED COVER AND ACCESS THE PRINT HEAD. HE DIDN'T THERE HAS NO ACCESS TO THE PRINTHEAD WITH THE LID RAISED!

  Hello

  Please click http://support.hp.com/us-en/document/c02257580 to access the procedure which should solve the problem.

  Please refer to two Solution.

• OfficeJet Pro 8500 910 has continuously check printer displays. This process may take several minutes

  If I print a box poster jam or the paper tray problem, but they are fine. What is the solution?

  Hello

  This article should cover the problem you are experiencing. Give the steps described a shot and tell us if it helps.

  http://support.HP.com/us-en/document/c02142414

  Good luck!

• HP Office jet pro 8500 910 a: downloaded windows 10 now does not print only spits out paper

  can someone help me? I downloaded windows 10 & now my printer prints a test page but if I want to print

  something else he spit only paper won 't print '.

  Welcome to the HP community @15matula,.

  I read your post about problems printing since the upgrade to Windows 10 as print black pages. However, the test pages print successfully, which shows us that the printer itself is fine. Maybe, it could be a driver problem.

  I recommend that you try to run the print and Scan Doctor to start. This diagnostic tool will allow to search conflict pilot other areas where there could be a problem of printer software. Try to print from Notepad again later to see if the prints will work.

  If printing is empty, run the Installation Wizard for Windows HP printer to install the correct drivers and software for Windows 10.

  Let me know what happens please! I hope this helps.

• The network file scanned Documents (PDF or JPG) = 0 (OfficeJet Pro 8500 has 910 bytes

  I have OfficeJet Pro 8500 910 has connected to the wired network with domain

  I created a shared network folder with read access to my computer (operating system windows 8 Pro X 64) through IP address of printer

  http://10.181.XX.xxx

  The shared folder has appeared on the screen officeJet and test with success, when I wear analysis on the officejet, the digitized file appeared on the network folder but with of size 0 bytes and does not open even it is pdf or jpg

  I have same door on the other computer is windows 7 PRo X 64 spouse for the same field and scanned documents open succefuly.

  Help, please

  My problem was solved by updating the HP 8500 has the latest firmware

  Thanks for trying to help me

• HP Pro 8500 printer 910 publish the connectivity / offline

  My HP Pro 8500 910 has played many years. Recently, he began to lose connectivity to the computer and disconnects when no touch button doesn't work on the printer including the power button. The doctor of scanning/printing HP said all is well, only after I have pull the plug of AC and repower save. Then, hopefully, after five minutes of inactivity printer the cycle starts again. I tried all the ten most 'no solution', nothing helps. The printer is connected to the laptop via a USB port that I moved the laptop and docking station. The only thing that I did is to uninstall and reinstall the original HP Print software. P.S. The e-print function works well and print when the printer is in "ready" mode Help!

  My HP Officejet Pro over 8500-910 'connectivity' was resolved. The current design of my product does not have the e-print function be on permanently because it prevents the restart "standby" mode. Given that this feature has been disabled the printer works fine just without the e-print software on. Thanks to the Technical Support employee, Jennifer, she was able to help diagnosis the problem.

• OfficeJet pro 8500 a do not print

  My Officejet Pro 8500 910 has is top just print on cone winder or not at all that is the case with the test print I've tried HP Print and scan doctor he said nothing to fix. The drivers are all to date

  Y at - it something that I'm missing that could be the reason why he used print

  Thanks Dan

  You say that the problem occurs even when you print reports of self-test of the printer. Have you tried to print a report of quality printing under the Setup menu > reports to see if the problem appears in this report as well?

  In addition, see the document found here for the procedure help solve print quality problems.

• Office jet pro 8500 software for os 10.8

  I have a week I have Mac OS X 10.8 running.

  My not so new Office jet Pro 8500 910 a has a disk for OS 10.6.

  When you try to install the printer an error message is displayed.

  The help of HP suggests using the Mac update, but I guess as have not yet had time to do an update to the 8500.

  It doesn't seem to be a download again on the HP site.

  Any ideas on what I can do, and before anyone suggests, I don't want to buy a new printer!

  Well Yes, I recommend a few levels:

  1. the base drivers from Apple (at HP, in fact): http://support.apple.com/kb/DL907

  2. restart your Mac.

  3. download and install the full setting: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-108394-1&cc=us&dlc=en&lc=en&os=219&product=4083969&sw_lang=

• Configure and analyze the Officejet Pro 8500 a - 910 problems has

  HP Officejet Pro 8500 has - 910, Win 7 Home Premium (64). Two problems, maybe!

  1. no response when I click on "scan a Document or Photo - open the scan dialog box.

  2. impossible to set up 'Scan to network folder Wizard' get error "...". cannot write to the destination folder. "Set read-only permissions or wrong."

  Downloaded the latest version of the software, twice, but still failed to get a scan on my computer file.

  Copy on the printer works fine.

  Right click on the folder specified to send the scan to and under the modification of the properties to read only to shared. Also, your operating system must be password protected, so if you do not have a password, create one. You have a particular anti virus or 3rd party firewall? Under manage scanning settings in the HP software scans enabled?

• Can I have both Yosemite and El Capitan, installed on separate partitions on my Macbook Pro?

  I want to upgrade my Macbook Pro (Intel Core i7 2.8 GHz, 16 GB 1600 MHz DDR3) to El Capitan. However, I have an important piece of the software - Avid Pro Tools HD 11 - which runs on Yosemite, but not on El Capitan. Can I create two partitions, each containing one of these two operating systems and then choose to start the partition of Yosemite, when I need to use Pro Tools? If so, how should I do this? Is there a support article, I can read to help me? Can you Yosemite partition contain only the BONES of Yosemite, and the rest are on the other partition? Thank you.

  Yes, you can run them both. I guess the process is similar to this:

  http://osxdaily.com/2011/03/12/how-to-install-dual-boot-Mac-OS-x-10-7-Lion-and-1 0-6-snow-leopard.

  Having two OSs on separate partitions is like owning two computers, they are completely separate. You want to see in the two places will have to literally be in two places. Copy the files from one OS to another will be facilitated by a USB stick as if it were two separate machines, for example.

• OfficeJet Pro 8500 a: 8500 a plug the USB to the PC and wireless for Mac

  Our Officejet Pro 8500 a is connected via USB to our HP Pavilion running Windows 7. This connection works well. However, I tried to connect my iMac (OS 10.10.2) to the wireless printer with no success. If I disconnect the USB from the PC, I can connect wirelessly from my Mac. My question is: the Officejet Pro 8500 a does support multiple types of connections - one by USB and the other by wireless? If so, then I would appreciate help to understand why my Mac is not the 8500.

  Other details: our wireless router is Apple Airport Extreme. The wireless connection on the printer seems to work (I can print the details of this connection). However, when I try to add the 8500 to the Mac by using add printer, the printer does not appear. (The printer is lit and shows five bars of signal strength, SSID is correct and a valid IP address).

  My Mac is connected to the wireless network.

  Any suggestions?

  I was able to solve the problem of the printer with ethernet connection to the router that provides network wireless for PC and Mac. Now two machines are able to access the printer with no problems. By connecting with an ethernet cable, connect the printer wireless has been disabled. It had to be done because the wireless radio had become unreliable. The idea was that the blue wireless light never came. Thus by connecting wired LAN, all problems are gone. Thanks to the team of Geed for help.

• HP Officejet Pro 8500 has more: 8500 has more - will not print in color and alignment of printhead failure

  I have new ink cartridges, but it will only print in black.  Grayscale is not on.  I also cleaned the print heads several times and tried to line up, but this part came failure refers to the documentation.  What are the documents?  I would lov eto to be able to print in color again!  Any ideas?

  Hi @Adriana8,

  I see that you have problems printing in color. You have changed the cartridges and have the same results. I want to help you solve this problem.

  Please, try the following steps to see if it will help solve the problem. Ignore the titles of 2nd & 3rd documents.

  HP Officejet Pro 8500 printer - color or black ink prints do not.

  All-in-one HP Officejet Pro 8500 (A909) and Officejet Pro 8500 has e-All-in-One (A910) Printer Series - one "ink cartridge appears to be missing or corrupt" control panel displays error on the printer.

  'The following printhead appears to be missing or damaged' display for HP Officejet Pro 8500 has e-all-in-One Printer Series.

  You use genuine HP cartridges?

  If you appreciate my efforts, please click on the "Thumbs up" button below. Good day! Thank you.

• OfficeJet Pro 8500 has more: impression of 8500 has only black and yellow

  Pretty simple problem.  The cyan and magenta colors do not print.  The cartridges are all fairly new, PLR and lines of supply to the printhead not are not tangled, etc..   I wonder if I need to replace the print head.  The machine is almost 4 years old.

  Thank you

  TP

  Hello @thomasapayne,

  I understand that when you are printing on your HP Officejet Pro 8500 has more e-All-in-One Printer Color Cyan and Magenta will not print. I would like to help you today with this problem of print quality. Thanks for the troubleshooting steps that you received before reaching out for support, including. Currently, there are a few quality printing additional troubleshooting steps that can be done to resolve this Cyan and Magenta print quality problem. However, if these measures fail to solve this problem of quality then a replacement Cyan and Magenta Printhead will likely be needed. That being said, can I please have you follow the steps below.

  To begin troubleshooting can I please have you click here. Once the support document opens, please follow the steps under four Solution. This includes step 1, step 3, step 4 and step 5 under four Solution. You may need to run the three print head cleans to unclog the printhead system. Attention do not exceed three clean because the ink is used during the process of cleaning print head. After troubleshooting is completed, please print another diagnostic quality report in order to confirm if the quality issue has been resolved.

  If the problem persists, a replacement Magenta and Cyan Printhead would be necessary.

  The print head should be is original printhead Cyan and Magenta HP 940. The part number is C4901A.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HP OfficeJet Pro 8500 first print and mirror for treadmill mouse and t shirt

  HP OfficeJet Pro 8500 first concerns.  I tried to figure out where the printer setting is for printing in mirror.  It is usually in the Advanced Settings tab.  I called HP and was told by 2 different tech, then supervisor that HP does not include this option in this printer.  I tried to explain how I felt it was hard to believe and I was told that it is most likely was an option that was no longer necessary.  I have his name and the file number.  I asked this bump up the level immediately above, because I felt strongly HP has not intentionaly left this option.  I digress.

  Can anyone suggest anything.

  Thank you

  Joe

  Thank you all

  Got it to work.

  990 has not worked, 5600 had mirror but does not print correctly.

  I went to the HP site and downloaded different drivers until I could get to work.

  Thanks again

  Joe