Z3200: 79:04

Similar Questions

• Z3200: Z3200 after Propairing Ink System: Shut downs

  We have an opportunity Z3200 who asked two print heads. Replaced all, and all was well for a while.  Turning off the plotter, removed from power for 1 week.  After turning the power on again the Z3200 boot. Then the screen turns off, shuts down the power botton, but PS fan will continue to operate.  In this state the power button lights not Z3200 return.  The rear power switch must be turned of, and then turn on the printer will go through the same process, and then closed, fan on again.

  Dianostics running, transmitted electronic Mod. Past of transport.

  Ran clear the NVRAM - OK

  Printer asked all print head needs to be replaced, Ok, all removed and reinstalled everything.

  Printer entered prepairing system print, but as soon as it beeps all makes, the printer stops back, empty display and the dark green power button, but the fan of the power supply running.

  And suggestions or solutions out there?

  Spoiler (Highlight to read)

  Thanks for the information!

  Here's what worked for me:

  After going around in circles with this, I removed all of the print heads, tool to clean all the contacts, two or three times.

  Then after seeing a sort of film on the back of the print heads, their contracts, I cleaned the institutions.

  I saw this being a problem on of the Z6100.

  Then I repeated the process clear NVram.

  Has passed through the stages of replacement print heads.

  The system went wrong the 4 process and did not fail this time.

  Adding paper, crossed all the lines and the color calibration!

  Back online.

  [Everything was fine before, until I stopped and unplugged a few weeks ago]

  Thanks again!

  Spoiler (Highlight to read)

  

• Designjet Z3200ps photo: Designjet Z3200 cannot print red

  Hello

  I had beautiful posters on my printer printing problems, because the colors are not exactly what I was seeing on my screen. Most of the color was beautiful, but always seemed a little cold, devoid of the Red range orangey color. I have calbrated the printer twice and all the colors look perfect. After several unseuccessful attempts to manipulate the colors with the HP utility

  I decided to print a color chart with red, green, blue, Cyan, Magenta and yellow. All the colors are almost perfect, except for the Red; He printed almost black. What is c? How can I fix? Moreover, the Red cartridge is new, but there is no deal.

  Thank you

  Max

  I suspect that your black carpet & red printhead was bad... replace & try again. also your media color calibration

  Use of course good icc profile for the paper you are using. myself using the HP everyday photo glossy or satin paper.

  or brilliant canvas. I use all the hp photo gloss/satin with icc GE Profile & very satisfied with the results.

  My Z3200 44 '' 2 print the most beautiful, colorful posters vives, pictures etc and I also have 2

  Z3100 & so perfect print

• Z3200 printer utility

  Although my Z3200 and Photoshop CC shows print custom, the printer utility shows no.  I just installed the latest version of the utility (27.0 6 March 2014).  Operating system is 10.9.4

  I rebooted the printer and the computer and the printer utility says still no custom print media.

  Ideas for a quick fix?

  This forum focuses on the level of consumer products.  For the Designjet that you can have better results, post in the forum HP DesignJet here, this is where the DesignJet experts.

• Designjet Z3100, Z3200 lcd white & green power flashing lcd

  I have one of each Z3100, Z3200 44 "model and both virgins panels lcd, also the power lcd green kept flashing?

  I looked in the service manual and nothing mentioned about this problem.

  Any sugguestions where to start first?

  It could save you time and ask this stupid question first here, as so many pros on this forum & might already knew...

  Thanks for your help...

  Thanks for the kind & professional, more technical help on the forum who has solved the problems of our HP Designjet users of

  time to time, even better, faster & effiencient more than HP.

• How to obtain warranty support - ink cartridges for DesignJet z3200

  I have a HP DesignJet z3200 only two colors of ink (MK / LM) stopped printing.  The diagnostics say there are still a lot of ink in the cartridges and they are still under warranty, but when I try to get a warranty support via the Web site it does not get additional information (email or phone number).  Does anyone know how to obtain warranty support for ink cartridges?

  Thank you

  Support for your product number is 800-334-5144. I am also including a link to the support page Hp that list of e-mail and telephone contact information.

  HP support

• DesignJet Z3200: HP Z3200 calibration/profiling issue: Error 58:10 ESP

  my old Z3200 5.5 years prints perfectly. I wanted to calibrate/profile of new media, I had bought. but when I started the calibration/profiling of new media, the process fails and made the mistake of digitization that failed after the printing of the calibration sheet.

  diagnosis of ESP test failed with error 58:10. I went through all the information which is available on the net about it and did what ever has been proposed: clean the print heads, to rehabilitate the printheads, update to the latest firmware version, etc. all look the same test prints correctly, even if some printheads are no longer under warranty. I also disassembled the machine by following the instructions in the manual maintenance and on different forums on the net and cleaned the unit of ESP. but still the same problem.

  then I noticed that my ESP unit looked a little different of substance over all the images available on the net. There is a small mirror inside outside shutter. It seemed a little dirty, so I cleaned it. but always without success. then I thought that maybe it is supposed to be covered and some coating must have fallen. so I put a top band. ESP test succeeded and I was able to profile new media. but after two successful profiling the problem started and I am not able to calibrate/profile of new media.

  any help to solve the problem will be very much appreciated.

  Cheers. Sanjay

  This forum focuses on the level of consumer products.  For the Designjet that you can have better results, post in the forum HP DesignJet here, this is where the DesignJet experts.

• HP Z3200 incomplete printhead replacement - restart

  Hello

  Recently, I replaced all the inks on this machine which had served market for the past 4 years.  The inks have all expired and were out of warranty, so they were replaced by new inks.  Yet, I couldn't run GMG ColorProof calibration so I replaced now all print heads.  Managed to get 5 of 6 print heads, out of stock on the chromatic red until the end of the year and always get the message "Incomplete print head replacement" that lists all the printheads as needing to be replaced.  I never had this message with the old print heads, but now, when I pass the old ones back in I get this message.  I tried to replace the printheads several times.  The message always, that the print heads need to be replaced.   I hope that the problem will be solved when the last print head is installed, but that will have to wait until the new year.  Any suggestions would be really appreciated, thanks.

  That was it, the sensor window was loose.  This made it impossible to complete the installation of the print head.  Now, running through the installation program, lcd says 22 minutes.  Working finally discovered why didn't fit the last print head, was the Red print head 70, was supposed to be 73! Heck! Using the old expired for the moment thank you all for your help.

• Designjet Z3200 Photo: Designjet Z3200 Photo - paper will not load

  I got this plotter for less than a year (although it was purchased through a school and languished in receiving for a while before I was in fact, the guarantee is therefore).

  Today when I tried to load photo paper in it he refused to recognize that I inserted the end of a roll in the plotter. I went through the procedure of typical paper loading, but it seems that the sensor that records the fact that the document has been inserted is borked/don't normally work. He's always telling me to load paper.

  I tried to lift the locking lever to see if I could advance the paper and do recognize it, but had no luck.

  The plotter was sitting idle for several months during the summer.

  I can't find documentation on this problem. Is this typical? It's just a bad sensor? What?

  I used previous generations of this tracer a lot in the past and would call me as at least a moderate user in advanced. I've never had this problem

  Advice? Patches? What is it going to cost me, since I'm now out of warranty? It's a little irritating, as I ran less than 50 feet of paper through this thing - I don't expect that broke quickly.

  Thanks in advance!

  Problem solved thanks to another thread.

  OOP sensor has been disconnected. No doubt some students unplugged knucklehead.

  Thank you! Sorry!

• loading paper HP z3200

  I bought the HDPE banner for use on a HP Z3200PS 44 "printer.  The paper does not load.  The message indicates that it cannot detect the paper, or he can't find the edge of the paper.  I tried out pretend by standard splicing of paper roll in front of the HDPE roll, but it was almost a disaster.  There are settings that can have an impact on the load roll paper?  Is it possible to substitute the edge of the paper problem?

  Thank you

  This forum focuses on the level of consumer products.  For the Designjet you can have better results, post in the forum HP Designjet here.

• Designjet Z3200 Networking question

  I have 2 identical Z3200ps plotters. It runs like a champ, and the other would be if I could understand this last question... adding to my pc to be able to print over the network. I am able to do the plank drawing through i.p. on web page address, and I can even ping plotter. However, when I go to add through devices and printers... nothing. I tried it from a pc Windows 8 and Windows 7. He research and can't find anything. I replaced the trainer and still no go. I could even send a print of the web page of the tracer. Also sent one when you're connected via USB. Any help would be greatly appreciated.

  Thank you!!

  Don't know how or why, but I came this morning, plugged the network cable in the plotter, initialized, and in some sort the IP config had passed from manual back to DHCP and picked up a new address. I changed the config manual, keeping the new IP address. Decided that I would try once more to add the Tracker on the network. You know, the sonofagun worked. I had activated impression more than 9100 last week, thinking the same thing you Milo. But after I did it, there was no change. Maybe it was just to take the time to update? Who knows... but anyway his work and I appreciate all the help.

• Designjet Z3200 24 in.

  Hello.

  I can not print on media of any of my Macs (normally print on media roll which still works fine) I can get the paper loaded in the printer without problem and it ends and knows that it is a sheet loaded and not a roll.

  But when I print from any mac that work becomes the pritner, then a message saying "load roller for the next job support" rises and it used to feel.

  I tried different files but still the same, been in implementing page and changed all the options sheet where I could find the paper source eg.

  Any help would be appreciated.

  Hello. Just tested this today and I fixed it by the Bill of lading, but indicating the printer is a roll. If the paper was beautiful and right he would not undergo a check of tilt loaded so well. I couldn't get the sheet to print any other way from a computer or a software package

  All the best

• Designjet Z2100: Buy a used Z2100. This who should I look for?

  I am considering buying a Z2100 used to, essentially, a few cents of a liquidator for recovery.  The printer has remained for months with no cartridge but some print heads (I know are probably trash). I have an another Z2100 that I can borrow the ink and the heads of the test, but only after I have to engage in the purchase and replace the timing belt.

  What should I look for? I don't mind sinking maybe $1000 in there, but I'm evaluating my risk of becoming much more expensive.

  Thank you!

  Z2100 8 color and print quality has not as good as the 12 colors like Z3200 etc.

  If you serious about print quality, sped up your money for the newer model.

• DesignJet plotter: ink cartridges T610

  For the T610 ink cartridges can be used after the expiry date on the packaging or expired cartridges will damage the print or machine heads? Thank you.

  Mysef using inks expired for more than 12 years and never have a problem. I mainly photos, posters, giclée print

  print... Currently, I have DJ500, DJ800, Z2100, Z3100, Z3200...

  Use only inks from HP, even expired...

  never use these so-called remanufactured or refilled inks... but if you can print something not important or simple

  color... maybe ok...

• Designjet Z3200PS Q6721B: Looking for old firmware for Designjet Z3200PS Q6721B?

  I've been fixing this mchine for over 2 months & never being able to finish since, even I already updated to the latest firmware, I have download from the HP Web site, I still don't have 79:04 after printer initialized 100% and never be able to load a roll of paper to make a print head alignment.

  Belt, service station, transport box, printheads, inks, tape Corder, all perfectly.

  But today I upgraded to the latest firmware again, once all 100% the machine firmware downloaded PC, then

  the reboot of the machine by itself. I stood beside and I saw after reboot & 1% apeared, then when he reached on

  60% & hour glass appeared & disappeared quickly, then bip & machine will restart. I tried again 2nd time and same.

  My other Z3200 44 "you always at 100% and why it only got to 60% & reboot by itself?

  I suspect the error 79:04 may associated with the unfinish firmware update?

  I'm looking for a link to download the old version to try...

  Thanks for your help.

  Finally I found what was wrong with error 79:04 of this printer when trying to load paper.

  Today I tried to delete the transport box & broke out in the center of the pulley, which has been the reaon when

  proposed per proposed transport and the belt box by unevenly and caused the error immediately.

  Happy another problem solved & fixed printer.