Cisco Wireless

I was wondering if someone could explain a little more local/central switching away, when it comes to HREAP/FlexConnect modes for CAPWAP AP So in our environment, we are short 7.5.102.0 code on all our WLC.  We have a WLC in two of our regions (Unite

friends, wonder if any of you have seen this before, you try to join a 1142 on a WLC_SRE version 7.4. the AP can ping the controller and vice versa.  In the graphical interface of controllers: monitor > Statisticc > join AP, I can find the mac of the

Hi all Anyone know what is the maximum number of points of access supported by Cisco 2504 WLC? According to the data sheet's 75: http://www.Cisco.com/en/us/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html But according to the

Hi all I would like to replace an AIR-WLC4402-25-K9 with AIR-WLC4402-50-K9 because of the amount of AP problem. The two controllers are running on the same version of the software 4.2.61.0. Just out of curiosity, can I just backup the old configurati

Hi guys,. I'm having some problems with getting the web-auth redirection to work properly. Basically, I set up an SSID with authentication of layer 3 and the customer's IP via DHCP, the DHCP server is configured on a win 2008 Server (192.168.10.18).

I created a single guest in WLC 4402 version 4.2 account and distribute to every visitor that comes in our society. However, when we receive a lot of visitors, the WLC end authenticate. Anyone know if there is a limit using a guest account?

Hiya, does anyone know if a 1121G connect to the WDS running on a 1242AG? Thank you Cameron

We have a wireless control system, 3 WLC and 190 APs. I need to listen to 802.11 radios via SNMP. The system is running with LWAPP and APs are not accessible via SNMP (no response trying to access). I'm trying to send traps on the Server SNMP (Zabbix

Hi all I have a requirement to apply webauth on my network of comments and therefore need to configure the functionality of lobbyadmin. We will have several users login (Help Desk, receptionists, etc.) using an account of lobbyadmin and from a manage

I have a WISN and we use open web Cisco authentication with a user's e-mail address. When executing this CLI command: > config network secureweb disable > save config > the system This will make the web authentication come HTTP instead of HTTPS?

Experts, I did some reading, but it is difficult to have a clear vision. I'm looking to understand the differences between map, RAP & WGB in cisco wireless and what conditions they are used to. Thanks in advance.

Hello I have a Cisco 5508 WLAN controller and three Access Points 3502i Cisco a Cisco ACS 5.2. I need to set up a simple wireless authentication system where a user is prompted to enter a user name and password in a web portal before you can access o

Hello Can you help me with the planning and coverage In fact, I add air-cap3302I ap to 78 m x 55 m, aps, how much I need? and you would help me with WCS, when I assigin the ap cap3502I-air to the map, I do not see the cover, the heatmap does not work

Hello I have a LAP1041N AIR. I understand that it is possible to turn this device into the AIR-AP1041N Cisco by downloading new software in the access point. Can someone help me by downloading the correct software and give a guide to do. Cisco want t

Hi experts, I wanted to know if it is possible to assign a DHCP pool to a specific SSID on the Cisco Aironet 1142. If so, what commands do I need to implement? Thanks in advance. concerning Fari

Hi all We are considerung to implement a new wireless solution based on Cisco WLC 5508 and 1262N Access Points. We intend to buy about 30 access points and have two options: either buy a WLC 5508-50 or, for redundancy to, two controllers 5508-25. Is

Forum I have some Access Points of demonstration I'll put up at a customer site.  I ordered the radios (1042N AP is so I could demo the N standard for them). Turning the Radio on the AP policy, I see the following options: Why is there not an Option

Dear all, I need help to choose the right part of the two TURN code access point in the object. Both the TOWER will be installed in the North Africa Morocco. Could you help me pls? Best regards Igor.

Forum This access point can be used in Mesh with the controller of 5500? Thank you Kevin

Hi all I m install access points to a place where the temperatures will be at-18 degrees, sometimes due to the condensation issue as water drops fells form the ceiling. as 1260 cisoc access points may be damaged because of this problem, I decided to