Cisco Wireless

Hello as I know if I have a 'b' clientsin my network connected to my access point, they will certainly lower the connection of all my wireless clients. so that all of the 'G' clint connects to the speed of 11 mb What about "N" 'G' if I a N AP with mi

Hello I'm looking for suggestions on what to do in this case: Have a wireless controller: WLC2112 and points of access 8, but im having problems with disconnections of ap´s, sometimes I can see the 8 ap´s and sometimes only 5 ap´s. I ran the command

Hello End-user has a WLC-4402-12-K9-V02 with 8 towers is currently working, in short time will need to add more towers that will be more than 12. How we can increase capacity to support 25 laps. concerning

How add and configure a new controller AIR-LAP1142N-E-K9 Access Point WLAN-AIR-WLC4402-12-K9

Hello Can someone up me please if its possible to create portchannel in a WLC2112 or a higher controller? Best regards

My wlc has stopped giving the ip address on a wlan. My guest access WLAN works well. In WLC message log shows: * 12:09:19.105 14 April: DHCP-3-SEND_OFFER_FAIL %: dhcpd.c:276 unable to send DHCP offers. A could not allocate appropriate ip address the

I am currently facing a problem with the WLC and AP. The AP is connected directly to the WLC. Join the AP and then ungroup you of the WLC. I saw a display error message. I wonder if anyone can advise me? WLC: 2100 firmware version: 6.0.199.4 AP: 1242

Hey all. My WLC 5508 is running with a dozen of AP, even if the driver is passed using pre-shared keys.  The plan should now migrate authentication Radius for our internal network... we will still use PSK in our vendor/visitor SSID. So 1 WLAN is inte

I've set up a WLAN guest who is using Web authentication to access the Internet. Layer 2 is open with broadcast SSID authentication. Guest users can connect to the LWAP, and when they try to open a web page, they are redirected to the Web Auth page a

I have connected an AIR-LAP1131AG-3560G and can see that the port given power in the newspapers, but nothing else - nothing in CDP, port watch also down/down.  The status light on the top of the AP is showing as blue/green, which, according to the do

Hello I have configured my aironet 1242 to involve multiple SSID, I put a management on the BVI interface ip address. The interface has been configured on the mode of the trunk on the switch. Everything works fine with the SSID but I'm not able to re

I'm a newbie in the technology of Cisco wireless. I have a lot of Cisco wireless access point. One of them (1142AG-K9 Cisco) I want to set them up as a DHCP server and will forward traffic to the public ip address as it will route the traffic to 203.

I'm kind again in the wireless world. I would like to buy a device that I can use to test the power of the wireless signal. Can anyone make a recommendation on a reliable product where it exists out there? Thank you Lake

I'm trying to update the IOS for Aironet 1252 G wirless access point, I look at all the instruction and they do not make sense! And there is just no instuctions on how to upgrade the IOS in the WEB BROWSER interface. I just did an install of Windows

Hello world... I am configuring a standalone AP AIR-LAP1310G-A-K9R. I have download the IOS LWAPP firmware downgrade software, I installed the firmware c1310-k9w7 - tar.123 - 11.JA4 and I am trying to configure the AP. Using the default configuration

Hi all I need to IOS c1240-k9w7 - tar.124 - 25d.JA.tar anypeople anyone has and can available to me by email, ftp or here on the forum? [email protected] / * /. Thank you!

I have no WLC right now in my office, but I ordered 2 numbers. Yesterday I 5 cisco AIR-LAP1252AG-A-K9 AccessPoint. I would like to convert in AP. How to do this. Help, please.

I have 2 model LWAPP AP 1042N each of them are connected to a WLC.  For some reason, I started to test DHCP on clients for these AP and controller wireless, and in doing so, I see change the status LEDs on the AP.  The most common transition is from

Hello I need wireless configuration comments anchor using webauthentication for a client. The building is located in a busy area and I fear that if I leave it to 'open' and webauth, much is close to wireless clients will associate the client to the A

What is the best way to debug DHCP throughout this unit activity.  We have this setting of the unit as a demo at a customer site, and is having some trouble with DHCP... Is there some opt for CLI and the GUI? Thank you!