8430 PXI cannot open serial ports

Similar Questions

• Cannot Get Serial Port to operate in virtual XP Mode of Windows (operating system is Windows 7 Prof SP1)

  I have a data record meter Extech quite expensive. The software so that it runs only on a PC running XP or by loading the software in virtual XP mode on a computer with Win7.

  The software works OK in virtual XP mode, and I can open previously saved data files. But with the operation of the software, I can not connect to the counter with his serial cable.

  I checked the status of the serial port in the Device Manager on this computer; time in the virtual XP and Win7. In both cases, it shows a COM1 and COM2 works satisfactorily. The only "yellow? s"in Device Manager are"VIRTUAL PC INTEGRATION DEVICE. " The connector Series 9 pins on the computer is labeled as COM1.

  The meter connects smoothly to multiple other XP computers. Flow baud rate 9600 and other port settings are set by the software.

  Hello

  Check out this article Configure a port for a virtual machine COM Microsoft to resolve this issue.

• Cannot add serial port in MAX

  Hello

  I have a cRIO 9076 and you want to use the port series. I can see the cRIO able and Automation Explorer, but I'm unable to add a serial port. I get the error "Internal Error Max could not get interface to database of the MAX". A new installation does not solve the problem. Any ideas what could be the cause?

  Thanks in advance

  

  Thanks for your answers, even if they did not help. Already tried to resolve this question of the repair of a corrupted Max database before posting here, but he has not changed a thing. An other error message told me that maybe NI-VISA has not been installed on the controller, so I installed just that. What I didn't know, is that you will also install "server of NI-VISA. Could be obvious to more experienced LABView users but I'm new to this software and the large number of software components is a bit frustrating...

  Anyway, problem solved :-D

• How can I open serial port VISA, automated?

  Hello.

  I have Labview 8.5.

  I have a program that works very well, on an interface series, on a well-known port (COM7). I have a converter USB to serial on my laptop.

  Is there a way to make my programm (.vi) to discover the port where my transformer is plugged? I want to open automated say.

  Thank you.

  Take a look at the discussions in this thread.  They discuss something similar.

  http://forums.NI.com/NI/board/message?board.ID=170&view=by_date_ascending&message.ID=322692#M322692

  R

• Tecra M1 - Modem does not work (could not open a port)

  I have a problem: after you have reinstalled Windows XP and on my Tecra M1 drivers, modem does not work. It can not diagnose himself - he always comes a warning: "cannot open a port (COM). It can be used by another device or application. I installed the latest Toshiba drivers for the modem, but nothing changes. How can I solve this problem? Looking forward for your advice!
  Best regards.

  Hello

  Have you installed the drivers in the correct order? Not? So do it!
  Have you installed the software or additional devices which could have a bad influence on the modem?
  Check the status of the modem in Device Manager. You don't see any yellow exclamation?

  Try to start the test on the modem within the operating system.
  Check the operation of the Modem under
  Start-> Control Panel-> phone and Modem Options-> Modems tab-> properties-> Diagnostics
  by pressing the 'button interrogate Modem.

  If the information window about the Modem contains a list of COMMANDS (including ATI2, ATI3, ATI4 etc.), then the modem is installed correctly. The ATI5 command ends with the number for the parameters selected regional (for example Germany = 06).
  To change the regional setting please use the Toshiba Internal Modem region Select utility.

• Serial port and parallel to ESXi 4

  Hello

  What about series and PARALLEL to VM mapping in esxi 4?

  Nothing. You cannot map serial ports or parallel in ESXi, ESX is required for this type of functionality.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• On the PXI-8106 serial port connection problem

  Currently, I am trying to connect to the serial port on the PXI-8106 via RS232 module. However, when I try to run the Test VI opened for COM1 MAX (PXI Remote) running on a PC, I received an error like below:

  Returns the status code: 0xBFFF00A8

  Name of the State: VI_ERROR_NPERMISSION

  Access to the resource or the remote machine is denied. This is due to the lack of sufficient privileges for the current user or the machine.

  Right now I'm just a just loopback test to ensure that the interface for device is working before you start my labview code. I'm not sure what the problem is exactly, if it has to do with the PXI or PC. Could you please suggest a few solutions to this topic?

  Thank you.

  I managed to understand. It did not work on the right platform.

• Base address Get Serial Port (PXI-8420)

  I have an application that requires a control to a serial port at low altitude.

  I need to recover (pragmatic) address for the COMX, which is generally Beach 0xXXXX.

  The card is PXI-8420, 2 RS232 ports.

  Thank you

  German.

  If you use Windows, you can find this information in the Device Manager by looking at the tab resources in the property sheet for the device.  While it is not guaranteed to be that of boot at startup, it will be in practice, as long as you don't add or delete everything material, change the topological layout of material (from slot machines in things are or the provision of connections in a system MXI), upgrade/downgrade BIOS or apply a really unusual Windows patch.

  If YOU have the information by program (in this case it changes), it can be obtained by calling the method CM_Get_Next_Res_Des (documented in the SDK documentation of drivers Windows - Google for it) on the device.  The sequence of calls to find your device and get all the parameters to pass into this function is very hairy, but it is pretty well documented if you have time to comb it.

  If you use a LabVIEW RT, so unfortunately I don't think there's an API that exposes this information.

• Cannot open COM1. Please check your port settings, XP SP3

  Hello
  I have some XP SP3 workstations that are used in the factory.  The shell of charge is attached to COM1.  When I test the appliance to make sure that all devices work, the shell load test will not open COM1.  When I use HyperTerminal to test COM1, I get the message "cannot open COM1. Please check your port settings. "I checked the BIOS of a workstation and compare it to the non-working station.  Corresponding to all of the information correctly.  When I check property COM1 resources, the station problem looks identical to the right station and no conflicts.  IRQ 04 corresponds to the current setting.  To get the workstation resurfaced to open COM1, I open COM1 properties, resource tab, uncheck and then re-check "use automatic settings" with your status to uncheck.  After having double checked the "use automatic settings", I click OK.  I then go back to see what the parameters are.  He changed his IRQ 07.  This change works until the computer has been restarted , and then the following steps must be applied again.  Also, if I perform these same steps on a workstation, I get the same results with the change IRQ.  I don't have the problem with com except COM1 ports.  We use the software in a box.  Change to use another com port is not an option.

  Thank you
  MANISH

  Hello

  Note that your computer is under domain, you must contact the TechNet forum, where we are the support technicians who are well equipped with knowledge on the issues of domain, do please visit the link provided below.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Cannot open COM1. Please check your port settings

  I have some XP SP2 workstations that are used in the factory.  I use Clonezilla to reimage the workstations (Yes, we have valid licenses for all units) where you have to replace a hard drive or have warranty work that requires a new installation.  We have put arrangements in place on the specified comm ports.  The printer is connected to COM1.  When I test the appliance to make sure that all devices work, the test of the printer will not open COM1.  When I use Hyperterminal to test COM1, I get the message "cannot open COM1. Please check your port settings. "I checked the BIOS of a workstation and compare it to the non-working station.  Corresponding to all of the information correctly.  When I check property COM1 resources, the station problem looks identical to the right station and no conflicts.  IRQ 04 corresponds to the current setting.  To get the desktop put open COM1, I open COM1 properties, resource tab, uncheck and then re - check the box "Use automatic settings" without applying the Statute to uncheck.  After having double checked the "use automatic settings", I click OK.  I then go back to see what the parameters are.  He changed his IRQ 07.  This modification works until the computer has been restarted so the following steps must be applied again.  Also, if I perform these same steps on a workstation, I get the same results with the change IRQ.  I don't have the problem with comm except COM1 ports.  We use the software in a box.  Change to use a different comm port is not an option.

  It seems that the cloning process is causing the problem.  Clonezilla is fast and reliable with the exception of what seems to be a problem of comm port.  I'm looking for someone who can tell me what settings can I change to make COM1 to work without having to go through additional steps after the workstation is restarted.

  Thank you
  Rick

  Hello

  The question you have posted is adapted in the TechNet forums. Post your questions here for a better response.

  Here is the link: http://social.technet.microsoft.com/Forums/en-us/category/windowsxpitpro

• This device cannot start code 10 and could not open selected port

  I load the driver for my track past tracking key Pro and I get the message that this device cannot start code 10. I show no upper or lower filters so the troubleshooting on found here does not work.  If I go to program followed past and then look for the device I get the message could not open selected port.

  I tried all USB ports and they work with other devices. I have a Toshiba satellite running windows 7.

  The company was no help.  Can someone help me please?

  Thank you

  Liz

  Your best bet is to contact the developer again, we have no knowledge of their products.

• Re: Portege R830-19 t: cannot find the Win XP PCI Serial Port driver

  Hello

  Creating a win XP to image for the machine above and can not find a driver for Win XP PCI Serial Port.

  everyone has ideas... looks like a pilot intel.

  any help appreciated

  Hello

  All Win XP drivers are available on the European driver Toshiba page and the serial port driver is also available.

  I found this one:
  [Win XP Serial Port Driver v1.00.000 | http://eu.computers.toshiba-europe.com/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 151 & selProduct = 6470 selSh ortMod = null & language = 13 & selOS = 10 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 3 & ID = 78794 & OSI D = 10 & driverLanguage = 42]

• Measurement & Automation explore (MAX) cannot find any serial ports

  Hello

  I tried half of the internet, but I can't find a solution for my problem. Maybe someone of you have an idea :-)

  My System Information:

  OS: Windows 7 (64-bit)

  LabView: LabView Professional Development System 2015 (32 bit)

  MAX: Version 15.0.0f0

  NI-VISA: 15.0

  NOR-Serial 14.0

  I've attached a screenshot of MAX at the end of my post.

  All the drivers for serial ports are properly installed (see another screenshot). But Max, I can't find these ports. There is only the error code "0xBFFF0011 (VI_ERROR_RSRC_NFOUND). If I want to add the COM Port via 'Devices and Interfaces'--> 'New'--> ' Port (serial or parallel) ", I can only choose between COM1-COM4 and LPT1-LPT4. But I need COM9!

  Anyone have any idea what I did wrong?

  Thank you

  deZeus

  I looks like something is wrong with your installation OR VISA (as MAX does not find ALL ports).  Make sure that NEITHER VISA is activated (sometimes of other kinds of visa in the way), or try reinstalling NI VISA.  Serial number NOR is not necessary since you are not serial ports using OR.

• Cannot find driver for PCI serial port

  I just installed a serial PCI on my computer (XP Home SP3) card and can be seen in the Device Manager; but it comes as "PCI Serial Port" under "other devices". When I try to configure it, it tells me that there is no driver available. How to get and install a driver who won't work. I suspect that it is a generic driver (probably vserial.sys) who, for some reason any never was installed in my folder System32. When I try to use my original Windows disks, I said I can't because the files on my computer are newer than those on the disks. Can I not download and install the driver from somewhere on the MS site?

  Thank you, I only wish that the story had a happier ending for you.

• Cannot connect my Samsung SCH-R450. Diagnostic Serial Port (WDM)

  Original title: why I can't connect my Samsung SCH-R450

  he do not otherwise than as a modem.   I can't connect to contacts, ringtones etc., calendar. This is what I get in Device Manager:

  SAMSUNG Mobile Modem Diagnostic Serial Port (WDM)

  Hi PatriciaLogan

   

  I suggest you to contact Samsung support for assistance on the synchronization of the mobile with the computer. See the help link - below

  http://www.Samsung.com/us/support/

   

  I hope this helps.