Access device on emulator 4.7 storm event log

Similar Questions

• VCE vblock, LSI_SCSI: Reset for device \Device\RaidPort0 ERROR in VM Windows Event logs

  Hello, I have been a problem for some time and I can't seem to understand this issue. Basically, the VM freezes but returns after 30 seconds.
  I found the problem was present on all data warehouses and even showed errors for for guests (san boot) boot sector. After changing the round robin at the fixed path on data warehouses to use a specific fiber channel switch LSI_SCSI errors were gone on all data warehouses, VM ect... everything worked normally.
  We have an installation program VCE vblock with UCS (blades), Nexus 5ks and VNX.

  So basically, we were troubleshooting paths FiberChannel beside the UCS to the VNX. We have changed ports on the VNX SP but side A was always bad / good B... Compared the configs of nexus for the two, identical configs/features beside the specificities as VSAN ect. Examined the configs for the UCS, but are fundamentally the same with Setup on the side B, but everything looked good. Nothing is defective.
  I noticed Tx errors on ports of module e/s and CRC errors on ports in the Nexus. Thought it might be a bad fiber so I replaced... The problem is always present. Any ideas? Thanks in advance!

  Data Center:
  UCS: 5108 Chassis, IO module 2104XP (2.2 (3g)), blades B200 M2, fabric 6120XP interconnections (5.2 (3) N2 (2.23 g))

  5.5 ESXi update 2

  2 nexus 5ks

  VNX 5500

  I found the culprit, SFP. The FPS that were used throughout the entire upward was incompatible and FUBAR would. Not match speeds, single mode when it should have been multi ect. Just all around the nightmare. It's on EVERYTHING from the VNX to IOM simply ridiculous. After completing the gutting of the SFP and the fiber, replacement and then delivered at the point of the chassis of the UCS everything was great. Honestly, I don't know how it worked at all with this configuration. Anyway, if you want something done you have to do it yourself.

• The event log does not start error 31: a device attached to the system is not functioning

  I can't get the service to start on my winxp sp3 pc event log. I have tried everything I know:

  • Running sfc/scannow
  • Reset permissions
  • Search for malware and viruses
  • Rebuild the WMI
  • Create a new account
  Nothing seems to work, I think that this is related to an error in hardware/device, but I see no problem in Device Manager. Can someone point me in the right direction to get this resolved? I don't really want to have to format or restore my PC...
  Thank you.

  * EDIT * well it seems to have fixed myself, I used regedit and navigate to the key:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\EventLog
  
  
  There, I found some records, I deleted the folder "Powershell" and the "Internet Explorer" folder, and the event log service, and then began. I had uninstalled IE and Powershell but these records were still there so I thought I would like to remove to see if he has made all the difference.
  Thanks for your time!
  -Antoni

• I noticed that my remote access has been activated twice in a week but I did not. no way to verify when, what, who activated via the event log,...?

  I noticed that my remote access has been activated twice in a week but I did not. no way to verify when, what, who activated via the event log,...?

  Hi dewthisnow,

  The information office for remote access must be in the security log.

  For more information, see:

  To disable remote desktop

  To view the logs in Event Viewer, see:

  Using the event viewer        

  Procedure to view and manage event logs in Event Viewer in Windows XP

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• Display the event log: event ID: 32, the driver has detected that this \device\Harddisk1\DR3 there cache write-enabled

  I recently discovered this error in my view the event log, do not know how to locate which disc it means or how to disable the setting cache: it's the XML view details screen.

  -

  -

    <>disc"/ >"

    32

    3

    0

    0 x 80000000000000

    <>2010-08 - 25 T 04: 28:36.363Z"/ >"

    85397

    System

    Stu - PC

   

   

  -

    \Device\Harddisk1\DR3

    0F00100001000000000000002000048001000000100000C00000000000000000000000000000000000000000000000000000000000000000

   

   

  I hope someone can help me with this work out I seem to have nothing else than problems at the minute...

  Thank you

  Download http://www.nirsoft.net/utils/shexview.html
  Disable all non-microsoft shell extensions (to explore) and reactivate a
  by so this can help.
   
  The filmThe Explorer accidents - in the control panel select Problem Reports and
  Solutions (Type wercon.exe in new task), go to historical problem, right-click
  your mistake and choose check for the Solution. You can also examine the details
  and AFTER the exact text of the ERROR here (that can pinpoint the source of)
  the error). .
   
  You can clean boot
  Troubleshooting http://support.microsoft.com/kb/331796
   
  Windows files for curruption click Start - all programs-
  Accessories - right on command prompt and choose Run as administrator.
  Type Cmd in the new task. Then type
   
  sfc/scannow
   
   
   
  --
  ..
  --
  "stusalford" wrote in message news: d85b4087-413f-4a7f-840 d-6b9c3ee73f0e...
  > I have recently discovered this error in my view the event log, do not know how
  > to find out who he average disk or how to disable caching: this is the
  > View of XML on the details screen.
  >
  >
  > -
  > -
  >
  > 32
  > 3
  > 0
  > 0 x 80000000000000
  >
  > 85397
  > System
  > Stu-PC
  >
  >
  > -
  > \Device\Harddisk1\DR3
  >
  > 0F00100001000000000000002000048001000000100000C00000000000000000000000000000000000000000000000000000000000000000
  >
  >
  >
  >
  >
  >
  > Hope someone can help me with this work out I seem to have nothing
  > but issues at the minute...
  >
  >
  > Thank you
  >
  >
  >
   
   

• T500 w Vista hangs light w HDD and event log error iastor with ID 9 (Device\Ide\iaStor0)

  Summary

  Edited: This problem was finally resolved by Intel Matrix Storage Manager driver 8.6.3 sent by Lenovo, January 13, 2009

  It is an intermittent problem on 500/T400 with XP or Vista 32.

  Vista 32: the HARD drive light stays on for several minutes, sometimes never goes. The machine crashes immediately, or it may continue to work for a while sometimes sluggish performance w. In all cases the operating system stops not completely so that the HARD drive light is forcing a hard stop with the keyboard, button on / off.

  XP: random BSOD of iastor.sys.

  In the log window of the events is an event of error each time passed than the HDD light grip. Source is iastor, Id is 9, and the text is "the device, \Device\Ide\iaStor0, did not in the expiration time. See below for a description of how show all events iastor error 9 in your event log.

  The problem has appeared since the second or third week of December. The likely source is an update of the Intel Matrix Storage Manager, driver version 8.6.0 delivered on 4 December.

  This driver has been after December 4, distributed via Thinkvantage System Update. T400/500 made in December were also shipped with this driver installed. Since then, lenovo has withdrawn the driver, drivers, T400 and page software here and the T500 here page now shows the driver for Vista 32 and XP as version 8.2.4.

  The experience is that this problem is solved in the restaurant or by installing the 8.2.4 version of the Intel Matrix Storage Manager driver. If the 8.6.0 driver was installed through system update, go to Device Manager and open the Intel(r) ICH9M-E/M SATA AHCI Controller. On the driver tab, make sure that 8.6.0 is installed, and then click the roll back button.

  If the T400/500 has been shipped with the 8.6.0 driver installed, first driver to download the 8.2.4 and run the extract in the c:\drivers folder. Update driver then choose Device Manager. On the second screen appearing to ensure you choose "Let Me pick from a list of drivers on the computer' - in the case otherwise, he will tell you, best driver is already installed when you click Next. In the next screen, select Intel(r) ICH9M-E/M SATA AHCI Controller and click on "disk" and on the next screen, specify the path c:\drivers\win\imsm.

  PS review iastor in case connection error messages comparing them to the update system install history as follows:

  1. in Control Panel, in administrative tools, open the Windows event log. If this is not the first time, you use the newspaper, you may need to select the local newspaper - the top left - line for the Summary window to open in the Middle, you can maximize this window down.

  2. Select the error line in the Middle window and click Show all instances of this event on the right side. All error events are now listed in the Middle window.

  3. click on filter the current view on the right side. In the new menu, enter 9 in the field of event ID, select ok and then Yes.

  4. you should now have a list of all occurrences of the error in iastor event. Scroll through the list and note the timestamp of the first occurrence of the error.

  5. open Thinkvantage System Update, then select historical spectacle of installation. Scroll the window to the right you see the timestamps. Examine your updates, just before the message in iastor appeared first in your event log.

  __________________________________________________________

  Original entry

  My new T500 a few days after the execution of the first update of the system began to hang once or twice every 24 hours with light on HARD drive and "the device, \Device\Ide\iaStor0, did not in the expiration time" in the registry.

  ,

  iastor is the Intel Matrix Storage Manager (MSM) for their device RAID/AHCI controllers. The Intel AHCI controller listed in as installed for the T500 shows version 8.6.0 Device Manager, which is the current version according to the Intel web site.

  There are zero warnings to disk in the event log errors, I ran the drive diagnostic - the drive is healthy. I don't think that this is a problem of DVD or disc, it's the MSM which is a failure.

  Googling on the MSM error message there is a certain. A batch is since last year and concerns of Intel THAT MSM supporting properly - l/min, this has been fixed in MSM 7.5.0 see http://www.intel.com/support/chipsets/imsm/sb/CS-025783.htm

  A second batch was held earlier this year for Dell laptops that, without looking into the details, seems to have been caused by an incompatibility between the BIOS and the MSM reported. (Update system to update my BIOS to 1.20 - 1, 01).

  Other solutions to this problem found on the web include the removal of iastor/MSM settings in the Windows registry to disable l/min and turn off AHCI in the BIOS.

  It would be nice to be able to verify that this isn't a hard drive problem by disabling the AHCI and therefore the Intel controller. How to do that in T500 BIOS Setup and what are the implications on the performance of my drive (Hitachi 160 GB at 7200 RPM)?

  
  

• run the system 7 pro. Can no longer access devices and printers OR convenience store can not print. Help

  I did everything that was asked of me, but nothing helped. I have no viruses/malware on board. I tried the fix Blutooth, I tried the fix noted. Nothing. I can't always access devices/printers or troubleshooting. I would accept with gratitude any suggestions.

  The system is a DELL System 7 pro auroura (replaced my XPS 8500 when it crapped out under warranty.) Don't want to launch another unrelated question but why 9 months microsoft since harassing me bootleg software when I use the official product delivered directly from DELL?

  Respectfully,.

  Dr. J. Michael (COOL Dr)

  Hello

  Try the procedure described in this link.

  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

• Event log of compensation after the reboot (storm)

  Hello

  One of my users is to have an exception "does not" my app that requires a reboot. However, after it reboot it appears that the event log is disabled. Is there a setting to force an event log persistent?

  The event log must remain after a reboot. However, it's a finite size and the oldest entries are allowed out when new is added and there are many connected to the start. Then references to your application can be removed when the user reboots.

• Circumvention of access to the event log

  Hello

  I have read in previous discussions that there is no API to read the journal of events (the one which is accessible via ALT-LGLG), but

  Is there some workaroud for the entries in this journal? Let´s tell a listener to intercept events before/after/lease written summer?, or maybe a way to read fields directly from the event log screen?

  Thanks in advance

  There is no way to recover the contents of the journal by programming.

• I am not able to browse the network. The workstation services and control of browser will not start. The event log shows the workstation service terminated with error code 2250.

  Internet, not able to browse computers on the network

  The computer has internet access, but I am not able to browse the network. The workstation services and control of browser will not start. The event log shows the workstation service terminated with error code 2250. Also in the event log Workstation reports: could not load RDR device driver. Cannot run the sfc in safemode, gives the 0x000006ba error, the rpc server is unavailable. Runs under normal windows, noticed in the registry last run: 0x000003e3 error code (try adding c:\windows\system32\drivesr\i81xnt5.sys to the dllcache)

  I'm puzzled.

  Hello

  I suggest you to send your request in the below link.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• Bold 9900 event log

  The usual key combination of Alt - L Alt - Alt - Alt and G L does not backup the event log on the simulator of the Bold 9900.  Instead, as soon as the first Alt - L is typed, a search begins with a double quotation mark is entered in the search field.

  I don't have access to a real device of the Bold 9900 to check whether the device has the same way or not.

  What is the key combination to bring up the log of events on the Bold 9900?

  Thank you

  Bold 9900 Simulator

  OS 7.0.0.261

  The default behavior when you tap the home screen is to open the universal search.  You can change this by going to Options, home screen Preferences and change the pitch by typing universal search to Application shortcuts.  This will allow you to use the shortcut Alt + lglg on the home screen.

• Java applications can write to the event log

  Two questions actually.

  I heard of an event log.  What's on the computer Pocket bb?

  Can do writing debugging information request in this newspaper?  Or any other text file, by the way?

  Debugging on the Simulator is one thing, but being able to debug on a physical device is another problem.

  Thank you

  Gerry

  Discover the EventLogger API

  To display the event log press the ALT key and type "LGLG".

  For the storm, show the keyboard and then press NumLock ' / ' /.

• Entry Windows - Faulting module name event log: Converter - agent.dll - after the partition of 100 MB WIn2008 R2 online

  Hello

  Since my installation of Windows 2008 R2 (Web edition server) use the restore system 100 MB partition, I had to use this fix for this:

  VMware KB: A Windows 2008 R2 machine P2V Conversion fails at 96%

  to allow VMWare Converter (last 5.1) to also copy this partition but I never did because when I changed status od this partition to the online converter always stops on the connection to the machine Powered-> this local machine with the error "Unable to obtain material information for selected computer.". I noticed input error to the Windows Application event log that contains:

  Name of the failing application: vmware - converter.exe, version: 8.1.0.15346, time stamp: 0 x 51642354

  Name of the failed module: Converter - agent.dll, version: 8.1.0.15346, time stamp: 0 x 51642321

  Exception code: 0xc0000005

  Offset: 0x00084bbe

  ID of the process failed: 0x19d4

  Start time of application vulnerabilities: 0x01ce7402f38eeb43

  The failing application path: C:\Program Files (x 86) \VMware\VMware vCenter Converter Standalone\vmware - converter.exe

  Path of the failing module: C:\Program Files (x 86) \VMware\VMware vCenter Converter Standalone\converter - agent.dll

  Report ID: 7d2c66a6-dff6-11e2-ab7e-000c29da83b7

  There is also an entry of information:

  The description for event ID 1 source vmware-converter-worker is not found. Either the component that triggers this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

  If the event is on another computer, the display information had to be saved with the event.

  The following information has been included in the event:

  VMware-converter-worker service started

  When I reboot the system and not to make agent system Converter online 100 MB recovery partition does not hang and I can perform the conversion without this small partition.

  Any ideas?

  Concerning

  Hello

  I'm back with the log file. The log contains only the related situation this topic. Before you start the new operation of conversion, I have removed all previous logs.

  Concerning

  EDIT: I checked the file workers journal and information:

  [PopulateVolumeProperties] \\?\Volume{90f40b30-30cd-11e2-849d-000c29da83b7}\ volume is the name of the \Device\HarddiskVolumeShadowCopy1 device.

  MEM > 2013 - 07 - 07T 22: 40:47.140 + 02:00 [info 06288 'Default'] [GetDriveLetterOrMountPoint] Mount point of volume \\?\Volume{90f40b30-30cd-11e2-849d-000c29da83b7}\ is \\?\Volume{90f40b30-30cd-11e2-849d-000c29da83b7}\

  MEM > 2013 - 07 - 07T 22: 40:50.881 + 02:00 [06288 panic "Default"] (recursion level Log 2) Win32 exception: Access Violation (0xc0000005)

  showed me where is the problem. I managed diskshadow.exe and executed delete conceals the entire operation. Now I can go ahead with the conversion. Thank you

• Tecra S10 - event log shows several errors

  My Tecra S10-167 has a problem since a few weeks now. In the event log, I have several errors, but especially this one:

  Provider of
  [Name] atapi
  -EventID 11
  [Qualification] 49156
  Level 2
  Task 0
  Keywords 0 x 80000000000000

  -TimeCreated
  [SystemTime] 2011-02 - 14 T 18: 20:12.558505100Z
  EventRecordID 3020
  Channel system
  Security

  -EventData
  \Device\Ide\IdePort0
  00000000000000000000000000000000000000000000000000 000004100000 0000100001000000000000000B0004C002000000850100C000

  My laptop gives me fatal errors and it restarts itself.
  Can someone help me solve this problem? Please guide me through this because I don't know much about computers.

  I have already reinstalled windows 7 with no result.

  Thank you...

  Hello

  New OS installation didn't help?

  Well, maybe something wrong with the RAM?
  Run tests of RAM using the memtest86 +.
  Maybe this tool allows to detect certain errors

  But unfortunately, the message displayed in your ad says nothing to me :(