After re-istall xp memory problems

Similar Questions

• I have a laptop Lenovo bought in the spring of 2008 running on Vista Home Premium. After years of basically no problem, I got warnings my memory was almost full.

  I have a laptop Lenovo bought in the spring of 2008 running on Vista Home Premium.  After years of basically no problem, I got warnings my memory was almost full.  I'm no computer guy, I'm a retired OTR trucker who now lives for people with disabilities.  I checked my system and found Lenovo had two partitions on the hard drive.  The main logic were my programs were only 30gig on a disk hard 150 gigabytes.

  After talking to some friends who know more then me and research, I copied all my personal files on a stick to 4gig and erased the hard drive.  Spent New Years day adaptation of files, wipe the HD, install Vista again and then 6 and hours of updates.

  Monday, I installed my old files, installed new software and reinstall some of my previous, as well as several updates of Windows.

  Tuesday a finer adjustment and more windows updates.

  Today, Wednesday, right off the bat I installed another Windows update.  Update has been installed, computer shut down, restarted, then the computer stopped at step 1 of 3 @ 97%.  I went for half an hour to come back to an error screen telling me I had a corrupted file and to reinstall Vista and using my factor disc repair system.  I wasn't allowed this option.

  I subsequently through trying different restarts that File:\Windows\system32\winload.exe has been corrupted or damaged or missing Windows update attempt.  Given that I had my Windows disk that I was never worried before making a boot disk.  I/we (family of 6) do not have the financial means to purchase recovery discs, go to a tech help.  We are ourselves.  Can someone help me out here?  Are all my personal details on my laptop, a lot of money and time tied up in programs, I can't access.

  I don't know how this forum works.  My email is * address email is removed from the privacy *.

  P. S.

  With all this, if I have to reinstall windows I better upgrade to a 32-bit on a 64-bit?  This will cause problems with existing programs? I see a noticeable improvement in speed?  I checked and I can't change to 64-bit.

  Hello

  Since you have a Lenovo, you can try to get to WinRE among advanced startup options (f8) and performa than a system restore or if you must organize a drive to install Windows Vista full version and try to perform a system restore in Windows recovery environment and check if that helps.
  For more information, you can consult the following articles:

  What are the system recovery options in Windows Vista?

• Satellite Pro 4600 memory problem

  What is the problem with this model? I bought second-hand laptop computer with 2 x 256 MB of RAM. After a few days memory module stops working (not recognized by the system), the next second module memory stops working. Problem is no slot, the two modules are defected some how. I bought memory as new ATC-SO815 AEC memory ten (www.memoryx.net), after one of the modules of memory stops working. BIOS is the latest Toshiba, version 2.60. Looks that mainboard burned some how the modules of memory, it's not good for me, I've already spent too much money for this laptop.
  What's wrong??? Is there a solution for this situation?
  I can't buy laptops and parts constantly, I don't have a lot of money.

  Post edited by: petar2258

  Hello

  How do you know that the problem is not associated with mainboard? I mean, you're a technician to know?

  As your machine is really old and you got no warranty on it, try the following:

  Install both modules of memory and make sure that the machine starts correctly.
  Download the latest knoppix (linux live CD), burn it to a CD, boot from this CD and choose at the start of the 'memtest '.

  Let memtest run for a day. If memtest reports no errors with your memory (you can see if the modules are defective), then your motherboard is faulty.

  So try this method and give feedback on your progress...

  Welcome them

• Failed to start after installing the new memory module Equium A60

  I have an Equium A60 laptop with the following specs:
  P4 3.06 GHz
  256 MB Ram (including 64 MB ATI graphics card)
  30 GB HD
  Windows XP Home Edition

  The problem is the following; I bought a bar of memory in order to update my system. I bought a Kingston SO-dimm pc2100 512 MB. After installation of the memory of the laptop wouldn't start, after about 5 seconds after having turned it on, it turns off completely.

  If I remove the memory it starts up fine. I had tested memory and its ok so there seems to be a problem with the laptop itself. I'm confused, so if anyone has an idea of what might cause boot failure, I would be happy to know.

  Thank you very much...

  As far as I know the main reason for the failure of start is the use of non compatible modules.

  According to the specifications of the laptop, you must use PC2700 512 MB (PA3312U - 1 M 51). If you want to buy the module Kingston (products of very good quality) check it please the Kingston MEMORY SEARCH

  Good bye

• ELITEBOOK 8440p: memory problem - the WIERDEST OF SYMPTOMS!

  I can't understand this!

  I have a 8440p (Core i5) Elitebook. It has 4 GB of memory (2 GB under keyboard and 2 GB in the expansion port under the flap on the bottom of the computer). It works fine like that for many years!

  Recently, I became troubled windows of memory (blue screen, blocking, etc.), so I started studying.

  1. I took out the memory expansion module and it worked fine (computer total memory = 2 GB).
  2. I put it in backwards after the cleaning and back problems (computer total memory = 4GB).
  3. I took keyboard SODIMM memory and replaced by what was in the extension of memory, (computer total memory = 2 GB) - all very well worked.
  4. I then added the 2 GB that was originally in the memory of keyboard expanion memory (4 GB total) and same problem returned!

  Does have any sense to anyone at all?

  The only conclusion that I can do is:

  1. My two modules of memory work correctly.
  2. My expansion slot memory is faulty (no memory).

  Anyone recognize?

  PS my SODIMM memory have only 4 chips on each side (total 8). I think that it what is called 'high density' memory, but it's how the computer was delivered!

  gocat9

  I agree if she had not worked so well for so long the original high density modules. But now you can choose I would get low density for this new chip 4 GB. It is not that high density does not at all; on some models, it causes problems of comaptibility as wrong to interpret the ability or the refusal to run in dual channel.

  Let us know if you need help most.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• My data hard drive is about to die, or it is related to a memory problem?

  My windows 7 x 64 operational system joined as well as all my applications is installed in an ssd and there is a hard drive to store data. My system is as follows:

  Motherboard: GIGABYTE GA-X58A-UD3R

  MEMORY: KINGSTON KHX1600C9D3K3/12GX DDR3 12GB (3X4GB) PC12800 1600 MHZ HYPERX GENESIS TRIPLE CHANNEL KIT

  CPU: Intel Core i7 930 (s1366, 2.80 GHz)

  PSU: Enermax MODU87 + 700W 80 + gold PSU EMG700AWT

  HARD drive: Western Digital Caviar Black 1 TB HDD (64 MB of Cache, 7200 RPM, Sata III)

  SATAIII SSD : SSD Samsung 840 PRO Series 265 GB (model MZ-7PD256)

  I rarely have the problem which is depicted in the icons following (I speak for hard drive data storage):

  No preview of the photo, but I can see a specific image when I double click on it

  

  

  records are missing

  

  After this problem, I went to check if the same thing was happening in the icons in the primary system ssd. Therefore, I went to start--> pictures--> sample photos and I could see a glimpse of the images.

  

  I was also able to move through each folder I wanted in the ssd. Then I double clicked on 'computer' icon and the following happened.

  

  I was able to close the window without any problem. I think that it is a hard drive problem, but could also be a memory problem. What is your opinion on that? Another weird thing that happens, is the loading time on a cold start the msconfig.exe file. Sometimes the file loads instantly and other times it takes several seconds (7-10) to load on the screen. If it is not a cold start, then the file always loads instantly. The same thing happens also with the Task Scheduler. It seems very strange to me. Please note that Superfetch, Prefetch, Defrag, Windows backup and indexing are disabled.

  Finally, I found the solution to my problem. When I got a memory low message (12 GB of installed RAM memory) I couldn't believe my eyes.

  

  I immediately opened the resource monitor, went to the memory tab and I just saw the dllhost.exe file has consume all memory. I thought that this file was infected and I checked both versions of them (x 64 & x 86) with virustotal, but it wasn't the issue. When I read that this file system is loaded to restore media files in thumbnail view in windows Explorer, I remembered that I had a defective mp4 file that could not be opened. I knew I had to do. I had to delete this file. The problem is that while you try to remove a defective media file, the dllhost.exe file tries to make it, so you are not able to delete until the end of dllhost.exe through process Explorer process.

  Conclusion: When you see a media file that it is not rendered in the thumbnail, view then this file is probably defective and the dllhost.exe goes to an infinite loop, while he tries to make this file, until it consumes all your RAM memory!

• Memory problems and questions related to the process

  Does this look just for you, because the modified memory does little until after I had computer problems and had to do a factory reset

  The operating system is Windows 7 64-bit edition SP1

  I disabled SuperFetch is told by the way, if this help anyone on this issue.

  Resource monitor

  

  Windows process

  

  Services

  

  

  

  Performance

  

  Hello

  When your computer doesn't have enough memory for all the actions it is trying to perform, Windows and your programs can stop working. To help prevent information loss, Windows will inform you when your computer is low on memory. You can also learn to recognize the signs of low memory and take measures to prevent the problem. Insufficient memory problems occur when your computer is running out of RAM and becomes virtual memory. This can happen when you run more programs that the RAM memory installed on the computer is designed to support. Low-memory problems can also occur when a program free up memory that it needs more. This problem is called memory overuse or a memory leak.

  You can consult the following Microsoft articles and check if it helps.

  Diagnosing memory problems on your computer

  http://Windows.Microsoft.com/en-AU/Windows7/diagnosing-memory-problems-on-your-computer

  Prevention of problems of memory

  http://Windows.Microsoft.com/en-AU/Windows/preventing-low-memory-problems#1TC=Windows-7

  You may receive an "Out of Memory" error message because of the limitation of in Windows Vista or Windows 7 desktop heap

  http://support.Microsoft.com/kb/947246

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows7/Back-up-the-registry

  I hope this helps.

  Please post back with the State of the question and we will be happy to help you further.

• Microsoft Photo Viewer memory problem / unable to print images... (2 questions)

  The other day I tried to print a photo (.jpg file) color - so I deactivated the "Print in grayscale" checkbox in the properties of the printer (just like always).

  But after clicking on the OK/Print button in the Print Wizard Photo, 4 the same error windows pop up.

  Translated from Danish:

  "An error occurred during printing.
  "The images cannot be printed due to the following error:

  ... But there is no description of error?

  Now 4 error popups every time I try to print an image (.jpg or .png) - but NOT when you print documents containing images (.pdf and .odf) that prints very well.
  .txt files print as well...

  Standard Windows 7 Photo Viewer no longer works. He tells me that I have not enough memory on my system to display the selected image (.jpg-file 3 MB)...

  I'm on a system Windows 7 Home Premium with 4 GB of RAM installed - I'm only using about 1 GB of them at the moment - is NOT a memory problem.
  The CPU usage is also about 1%...

  Any thoughts?

  Kind regards

  I hate this chime late trying to solve this problem, but I had the exactly the same problem (per month) and finally resolved.

  What has not worked:

  • Reinstall Windows 7 as an upgrade on the spot.
  • Upgrade to Windows 8 (improved the situation, but did not fix)

  What makes:

  • Create a new user account, it set until I transferred the old user account settings.
  • Set the color management settings.

  Before you reinstall, I suggest to create a new user account and try printing once logged into the new account. If the photo printing Wizard works when logged in with a user account, the problem is specific to the settings for the user account with the problem.

  To check the color management settings try this:

  • Click Start
  • Color in the search box type
  • Click on color management in the results of the research
  • Click the Advanced tab
  • Make a note of any settings that do not start with the system default
  • Change all settings that are not listed as default from system to system default
  • Close the color management dialog box and try again the Print Wizard

  In my case it was a colour profile Adobe corrupted causing the problem.

• JRun.exe memory problem

  I use Coldfusion 8 Developer Edition as a test server for the development of Web Dreamweaver sites. I am running Windows Vista Home Premium and 2 Gig of memory. When I start my computer I will meet some memory problems that I traced to jrun.exe that part of Coldfusion. For perhaps the first time jrun uses much more together half a million members. After that it drops to about 60 000 k. Does anyone know how to reduce?
  
  I am a user of medium level with no experience of server beyond establishing edition developer of CF admin using mostly default settings. I found bandages on this problem, but all were way over my head. All suggestions must be very precise and not in server admin jargon.

  I have not the slightest idea what a 'max heap' is or what "garbage collection" is, but I found the setting of the administrator. I reduced from 512 MB to 256 and it does not seem to affect the application to all, and it reduces the memory usage to the point where it does not affect other applications. Thank you.

• Equium L20-197 - memory problem

  I have memory problem with pc-world of computing L20 and currys sell the L20 with suite spec 256 MB of main memory and 128 MB of video memory (up to 128 no) when this is not the first case of all memory is shared and there are 64 MB main memory and when you try memory video in bios , it won't let you upward in rising to 128 unless you install another memory stick no matter who else noticed this problem? I know that the previous model of the L10 with intel video chipset was supposed to allocate depends of the video memory load, but there is no mention of this on the ati chipset model. all the ideas!

  Hello

  AFAIK usually specification is 32 to 128 MB shared memory. Probably, it should be possible to put it in the BIOS. On some units with ATI graphics card, it is possible to put it under properties of ATI (display properties > advanced). There is an option to change the value of the AMU which will change the RAM allocation shared to the graphics card. It's usually adjustable 16 MB, 32 MB, 64 MB and 128 MB.

  Can I really don t give you answer correct but my friends a laptop with 512 MB RAM and it works fine.

  Good bye

• When I select a sequence of five frame to render HDR in Lightroom it merges files in a preview very well. But when I click on the Merge option, the progress bar is obstruction of about 42% complete. I suspect a memory problem, so I spent a few hours Unite

  When I select a sequence of five frame to render HDR in Lightroom it merges files in a preview very well. But when I click on the Merge option, the progress bar is obstruction of about 42% complete. I suspect a memory problem, so I spent a few hours uninstalling a bunch of useless software on my laptop and still photography will not merge the HDR sequence. It worked once before, but now it does not work. Help!

  I just 8 GB of RAM and have been able to put together five separate images HDR images. I compared these files 5-image HDR with files - 2 and 3-image and see improvement very few (if any) using all five. Your results may vary, but you can try to reduce the number of images until you get your new laptop.

• After you install demo of problem Adobe DC Pro... meets an unexpected failure. Running Win 7. Any ideas?

  After you install demo of problem Adobe DC Pro... meets an unexpected failure. Running Win 7. Any ideas?

  

  Hi garym66400483,

  Please perform this cleanup tool to uninstall Acrobat Download Adobe Reader and Acrobat tool - Adobe LabsDC, reboot your system & reinstall it using this link Download Adobe Acrobat products. Standard, Pro | DC, XI, X.

  Let me know how it goes.

  Kind regards
  Nicos

• New PPr upgrade and memory problems now

  I upgraded my version of PPr CC 2015 20 days ago and I went back to make a project that I had previously worked on and made more than 3 weeks. Now, it will not be made and the computer is just running out of memory and encoding is abandoned. I am on Windows 7 with a 2 years old i7 processor and have been able to use the first Pro CC 2015 without problem until the upgrade to the latest version that came out about 20 days ago. Are there bugs that are being developed here? Thanks for any info. I had the project made out by removing all effects to make sure it was a memory problem and quite sure the file render out with effects off the coast. However, I could make with effects on before this update.

  Thanks for you response Brian.

  Can you remove the effects of light and then give it a shot? Effects of light seem to be common with those who have reported this problem.

  Thank you

  Regalo

• Memory problem... Can someone help me please?

  I have Windows 7 64 bit with 8 GB of ram...
  I have installed SOA/BPM running the DEV version (IE is running with the ADMINISTRATOR of the server) and I begin to see the errors in the log...
  What I can shape to allow to WebLogic remain in place and be happy with memory, that he (the Task Manager shows 3g available)!
  
  < 26 August 2011 12:35:04 CEST > < critical > < health > < BEA-310003 > < free memory in the server is 4 867 280 bytes. There is danger of OutOfMemoryError>
  
  THANKS to YOU all!

  You can set your args memory in your [your path]/user_projects/domains/domain1/bin/setSOADomainEnv.sh

  That's what I put and I have no memory problems more. Other values (below) may be more appropriate for your machine. He recommended to do not to go higher.

  DEFAULT_MEM_ARGS = "- Xms2048m - Xmx2048m".
  PORT_MEM_ARGS = "- Xms2048m - Xmx2048m".

  Heidi.

• memory problems after installing the network card passthrough.

  First of all, Thanks for the help.
  I installed a network card passthrough directly to a Windows machine on ESXi 5.1 and start the machine when I get the error:
  
  Group VM.6791: invalid parameters for VM memory allocation vmm0: XXX. () min: 3670016, max:-1, minLimit:-1 actions:-1 units: pages)
  Group VM.6791: cannot Admit VM: memory admission check failed. Asked booking: 3716761 pages
  SharedArea: Unable to find 'testSharedAreaPtr' in SHARED_PER_VM_VMX domain.
  
  I looked at articles and don't see that only the value parameters Backup of the RAM, but If I change these settings, I get the following error:
  
  Not valid parameter memory: memory reservation (sched.mem.min) must be equal to memsize () 14336) .
  
  Thanks for the help.

  What is the memory you have allocated for this machine?

  Can you increase the amount of memory reserved for this virtual machine to its configured memory size and try to turn it?