Audio USB key multicanal never works!

Similar Questions

• USB keys do not work in my VISTA PC, but working in the XP computer.

  My PC is only a few months and underwarranty. VISTA is OEM original and authentic. All updates and installed SP2.

  But I have several problems with VISTA.

  One of them is the following:-

  USB keys do not work in this PC. Initially, they are recognized, but as soon as I start the data transfer it stops and does not recognize the keys more. Same USB keys work correctly on other XP computers.

  An external hard drive works perfectly on the same USB port. If the port is fine.

  Hello PG_eu,

  First of all if still under warranty, contact the manufacturer to execute tests for your USB slots. Have you tried to see if other devices work on the USB plug? The manufacturer of your may be able to replace your computer if needed.

  Then, I'd go for the Device Manager to see if you have errors. Go to Device Manager and see if you have a yellow fringe! showing that there are errors with your USB devices. Open the Device Manager in Windows Vista via the management utility of the computer, the Control Panel, or from the command prompt by typing in devmgmt.msc.

  You can go to the different tabs and see if the devices work properly, should be cancelled or update your drivers.
  You can also go into the event viewer and see if you have errors on your hardware devices.

  I hope this helps.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Usb keys do not work on HP CM1415FNW

  I have a printer HP CM1415FNW. I need to scan and transfer of files on my usb key. In fact, the printer may read less than 8GB, over her keys cannot read.

  Is there a solution?

  According to this Manual on the walk up to the USB function, the printer does not support USB flash drives, over 2 GB, so it's likely that the 8 GB working.  You could try to do an update of the firmware and see if that gets a job 16 GB, but more probably it won't help.  If you need help with the update of the firmware, I would like to know what operating system using the your and I'll connect you to the latest version.

• Pny 4 GB USB key does not work on my new computer?

  PNY 4 GB USB attached flip key will not work on anything ive tried including the update of drivers on each computer for that material and all the drivers?

  Unfortunately this did not help, the USB is not but the age a year but already had important things, Ive already lost the last 6 months b/c my new windows 7 was a pilot missing and with my boot cd "s out of State, I had to restore to be online for school»

  Unfortunately - when one of these drives (USB thumb drives) goes to the South, more often - it is always toast.  There is no real help to recover the data: that is why everything should be saved.

  You said you tried it on several computers (... on all computers...) so it's probably a Goner.

• Qosmio F60 - ports USB & keys do not work

  Hello
  After a clean install (win 7 home prem), I found most of the drivers, but still have following problems.

  (1) when I plug in my external hard drive or any device to any usb port, although he feeds and try to read, but does not appear in my computer and does not

  (2) the keys to touch (eco, wireless, media buttons) do not work. After that added value pack is installed, it opens a button assignment tool and wonder for assignment entry keys

  (3) the reason for the clean install was new 250gig SDS to replace my drive hard toshiba 750 GB. It's the 3rd time hdd corrupted in 2 years (not happy), however, the ssd stops the laptop as well, and I have to restart

  Your help is very appreciated.
  [email protected]

  You have the latest firmware on the SSD?

  Have you installed all the drivers and software listed on the site Web of Toshiba? Make sure that you install the Intel Chipset utility first, followed by second PVAT.

  Also make sure you have Win7 SP1 before you install the drivers and update the BIOS to the latest revision.

  If you still can't make it work, you can order the Toshiba recovery disks and install the original image on the SSD, so everything works correctly.

• Multiple USB keys do not work on our Satellite A100

  In a conference of 4 of the 5 sticks provided by presenting his colleagues did not. The installation process has started, the message usual flashed in the status line, but then the facilities could not be completed ("Der angegebene Dienst ist kein installierter Dienst", i.e. "the specified service is no installed service' - my translation).

  The problem can be reproduced with a Sony 4 GB Stick, which can be brought to work.

  BIOS update did not help, install the new TI mass storage driver (both from the Toshiba site) did not help.

  Can anyone help? Thanks in advance,
  Martin

  State of the device is visible in Device Manager?
  Do you see yellow exclamation points or some error as the Code 28 error codes?

  If Yes, then I would recommend first installing all the updates of Windows and service pack 2.
  Then remove the USB device from Device Manager. You should remove all the USB controller and hubs from the Device Manager list.
  Reboot the laptop.

  After rebooting again Win XP should recognize the USB ports again deleted and should re-install the drivers.

  In my case it worked!

• Falsh USB key does not work,

  Windows keeps saying disk needs to be formatted, when I click on format, windows can be delivered by saying this format cannot be done. I tried changing the [default] fat to NTFS but always get the same answer.  Have you tried drag / drop images on disk, but nothing works.

  Can someone help please.

  Bigbruv.

  Try another computer. If this does not work on another PC, it broke. teengeek.freehostingcloud.com Microsoft community contributor

• Download USB key or camera.

  Why can't I download images from my camera or USB key.  Never had a problem until lately.  It "is like the port is dead and does not recognize anything.

  Hi GlendaFerguson,

  1. have you tried to use the USB key or camera on a different usb port and in another computer?

  2. what happens when you use other usb on the same USB devices?

  3. you receive an error message/code?

  4. What is the number of brand and model of the computer?

  This problem can be caused if the USB is corrupted or Windows cannot find the necessary drivers for the device. I suggest you to refer to the methods and check if it helps.

  Method 1:

  Run the hardware troubleshooting tool. Click on the link below.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

   

  Method 2:

  Remove and reinstall all USB controllers

  To remove and reinstall all USB controllers, follow these steps:

  (a) click Start, type Device Manager in the start search box and press ENTER.

  (b) expand Bus USB controllers.

  (c) right click on each device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  (d) restart the computer to reinstall the USB controllers automatically.

  (e) connect the removable USB storage device or camera and perform a test to ensure that the problem is solved.

  Method 3:

  If the problem persists, see the article help.

  My drive does not appear in Windows Explorer

  http://support.Microsoft.com/kb/330140

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the registry in Windows:
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  See the following Help article and check if it helps.

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  (Also applies to Windows 7)

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• USB port have stopped working

  Original title: windowsz 64-bit acer aspire 5332 usb ports no longer working?

  My usb key, used to work now that they just stopped? IV tried everything to remove all the drivers and install again and also have rebooted my laptop, if someone can help I would be very grateful! : o).

  Hello

  
  For further assistance, you can contact Acer. Check out the following link.
  http://support.Acer.com/us/en/default.aspx

• I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  What do you mean, your message is not clear.

• Tecra S1: Gets you a bootable USB key to work?

  Hello

  I tried many different tools to get my USB to work, but I guess that's the manipulation between my laptop and the USB key.

  In the bios, I have already "FDD".... "enabled.

  Maybe someone got his operation.

  One that works with the Tecra S1?
  What tool to use?

  THX a lot.

  Patrick

  HI patrick,

  as much I know boot from a USB (except a FDD drive) don't is not supported by computers laptop toshiba.

  You can try to update the BIOS to the latest version available ad try again.

  Sorry! :-(

  Tanya

• I used my USB key to work and computer encypted here my files. Now, he won't open all files on my PC at home. What should I do to recover my files?

  I used my USB key to work and computer encypted here my files. Now, he won't open all files on my PC at home. What should I do to recover my files?

  Hello

  You will need to work with the IT Department. to work to get the files not encrypted on the disc so that you can
  use the disk and the files at home. "" They could add ability to encryption of your system at home
  If you need that and they allow it.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• using a lexar Flash DRIVE to work on excel sheets. I went to open the USB key that ive been using and he said: 'it must be formatted. "

  i; ve been using a Flash DRIVE from lexar to work on excel sheets.  I went to open the USB key that ive been using and he said: "it must be in the format".  I did have to do at this point and that to format ill lose all my docs?  Help

  Try to play on another computer. If she still wants to be shaped, it's game over.

  If it's ok, copy the files on it before doing anything else and you get a new flash drive...

• Problems when I want to update my complete system Mavericks using a USB key with the installation program.

  I want to "Refresh" my Mavericks home cleaning system and I still have a USB key with the complete installation program.

  With this USB key, I installed successfully already before Mavericks. Now, I want to repeat the installation by booting from USB key. But when the installation starts early an alert appears, said something like "... the verification failed - something is changed on the volume...". "and the cant of the installation continues.

  I've archived the original "OS X Mavericks installieren.app" from the app store and I have properly prepared another USB key using the terminal app, referencing the original installer, but I still get this alert when I try to install with this new USB.

  It is necessary for me to work with the Mavericks, because it's the latest version of the system on which I can run Adobe Creative Suite CS6 correctly. With the later versions of OS X, I get problems on my Mac Pro (end of 2008).

  I wonder what could happen with my first USB data, as I have already installed Mavericks successfully with it under the same conditions and after that he never touched the stick again so far. What can I do? What is the reason for this? Y at - there a site where I can get help or advice to solve the problem or if necessary can I re-download an Installer 'fresh '?

  Thank you and what is Berlin

  You can make a bootable USB to install using this free program that will do all the work for you. Try running disk utility/repair disk be before installation.

  Bootable USB Flash Drive-Diskmaker X

• "SHIFT" on the Satellite Pro C660 key does not work

  G ' Day,.

  I have a little problem with my laptop Toshiba Satellite Pro C660.
  Unfortunately I had to remove the keyboard and thus dislodged the
  fragile plug to connect to the computer.

  The 'Shift' key refused to work since. All other keys work as usual.
  The only problem is the 'Shift' button does not.
  I tried to gently move the plug but made no difference so now have to
  Use a USB keyboard.

  Can you please help with suggestions for this problem?
  Thank you for your time.

  See you soon,.
  Sunrap.

  I really put t know what you think when you know that there is no connection for each unique key, but for the entire keyboard.

  To be honest I ve changed keyboard several times but never noticed this problem.
  Are the two SHIFT keys off function?