Color laserjet 4500 stripes CMYK

Similar Questions

• Color Laserjet 4500 on Windows 7-64 bit > share with XP - 32 bit > need additional 32-bit Drivers

  Here is the configuration:

  Desktop: Windows 7 Professional - 64-bit with Color Laserjet 4500, connected shared, and work very well. The driver name is HP Color LaserJet 4500 PCL 5.

  Laptop: Windows XP Professional - 32-bit.

  No network problem. Laptop sees the printer, but cannot connect without the correct drivers installed additional 32 - bit on the desktop. The drivers only I could find are listed here. When I try to add under host print properties/sharing/additional drivers, none of the .inf files downloaded are accepted.

  Since Windows 7 installed a 64-bit driver perfectly well, there must be a compatible 32-bit driver cab be added to allow the XP laptop for you to connect to this printer - but I was not able to find it!

  For any help or suggestion will be greatly appreciated!

  Rob

  I got to work:

  I copied the extracted driver files (with the file updated the hpbf231i.inf) to the laptop client XP.

  I used "Add a printer" on the laptop, installed as a network printer, stressed the shared printer and when you are prompted, pointed to the file hpbf231i.inf on the laptop.

  What time, eat enemies! But it works!

  Rob

• HP Color Laserjet: HP Color LaserJet - lines/stripes

  Hello

  I have a HP color LaserJet and I get a lot of lines and streaks on my printed pages.

  I also note toner inside the printer and my printer seems to take cleaning cycles more than before.

  Thank you!

  Although I work for HP, my posts are MY opinion and not those of HP.

  I would recommend some of the things

  First of all, make sure that your firmware is up-to-date, go to the page software and drivers on HP.com download and install the latest firmware available for the printer.

  Then, make sure that the toner collection unit is not complete

  Finally, print a cleaning of the control panel of the printer page, normally, you should select the following text in the menu:

  • Maintenance of the unit
  • Calibration / cleaning
  • Cleaning page

  You can also view this document as well.

  HP Color LaserJet Enterprise M552, M553 and MFP M577 - lines/stripes, toner and cleaning cycles dust excessive

  Hope that helps.

• Problem with Printer Color LaserJet 2600n of printing. Thin strips Magenta on the printed Pages

  I have a Color LaserJet 2600n, on which I replaced both magenta and yellow cartridges a week ago. Both cartridges are genuine HP. The printer cleaned and calibrated.

  Today, the thin magenta strips about 3 "apart began to appear on my printed pages. Print pages, but there is a 'click' stable, audible about 2 seconds apart from from the inside of the printer. Even after a cleaning several times, the bands are less bright, but they are still there. They also appear on the printed test page and on the page of troubleshooting print quality. Is there something wrong with this new magenta cartridge? This problem has never happened before in the 6 years, I've owned this printer.

  Here a link to the document that addresses the issues of print quality for your printer model. It will give you the different troubleshooting steps to try to resolve the problem. One of the steps in the document will guide on inspecting the print cartridge and see if the replacement is in order. I hope this helps.

• CE712A: Driver for HP Color Laserjet CP5225 for Windows XP Professional

  I can't find a driver for my OP de Windows XP Professional 64-bit for my CP5225 printer. Can anyone help?

  In other words, the printer is connected to your network with a rj45 cable I guess.  If yes you must go to the information on the printer menu and print a Setup page that will give you the address ipv4 of the printer.  It should be something like 192.168.1.12 now on you computer xp go to printers and faxes and add printer.  Local printer and do not check autodetect, then and on this screen, click on create a new port and the menu drop-down select standard tcp/ip, and then click Next. Type the address of the address of the printer (ipv4) that was on the configuration page and just keep on going until you get to the page of decision-makers.  On the left choose HP and will work on the Strip right down to Color Laserjet 8550 PCL or PS as long as one or the other, and then click Next and change the name to HP CP5225 or whatever you want to call the printer and you can check on this page to make it your default printer.  Complete and you should now be able to print to the printer.

• HP Color LaserJet M277n MFP: HP Color LaserJet MFP M277n CONNECTED to THE NETWORK, SHOWS NO INTERNET CONNECTION

  HP Color LaserJet M277n MFP printer, is connected to the network and I am able to print and scan. During the attempt to get the HP Web Enable services in the Web services configuration page, it displays an error: "connection error, check the internet connection".

  After you enter the IP address of the printer in the browser, I am able to detect the printer. To enable printing of HP, but unable to do so finds out the above error. Tried a lot of things including re editing of. When I check the printer, it shows the proxy settings are required / incorrect, where, as confirmed by the supplier that they use the proxy server.

  Help, please.

  Hello @JljoThomas!

  Thanks for posting and welcome to the Forums of HP!

  I understand that you have a problem of activation of the functionality of web services on your MFP HP LaserJet Pro M277n. I'd love to help you with this.

  First of all, you have the printer connected directly to a wall outlet or is a surge protector or power bar? Even if you have used a surge protector/power bar this whole time and you feel that this is not the case, please connect to a wall outlet so that we can eliminate the source of energy as the primary cause. Issues when connected to an uninterruptible power supply/Strip/surge protector power
  In this document you will see, QUESTION: questions or problems may arise when a HP LaserJet printer is connected to a UPS (UPS), a power strip or a surge protector
  ↑ This is not limited to the Laserjet printers.

  If this does not resolve the issue, we are going to let the router and unplug the power cable (NOTE: do not reset the router...), then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  If you are still unable to connect to web services after trying these steps, we can try to set a manual DNS server of your printer to connect to.

  On the front panel of the printer, press the wireless icon. Select it wireless TO get the wireless summary. Do not your IP address.

  1. on your computer, open a Web browser and enter the IP address of the printer in the address bar. This will bring up the embedded Web server (EWS) page.

  2. at the top of the page, select Networking.

  3. in the left side, select Identification network.

  4. in article for DNS, under primary (IPv4) enter 8.8.8.8, under secondary (IPv4) enter 8.8.4.4.

  5. Select Apply at the bottom of the screen.

  6. try to activate the web services again.

  If it is still unable to connect, try to enter 209.244.0.3 for the primary (IPv4) and 209.244.0.4 for secondary (IPv4)

  Hope this helps!

  

• How to connect my LaserJet 4500 to USB on new HP Pavilion Elite desktop 9517

  I have a new desktop Pavilion Elite M9517-c and you want to continue to use my hp laserJet 4500 color laser printer that has no USB connectivity.  Can you recommend a printer with a USB cable so that I can connect these two? Is this possible?  The printer is in great shape! Thanks for your response in advance

  My God, you're right it isn't the adapter, you need, sorry, here check this link

  http://www.emtcompany.com/catagories/USB-to-parallel-adapters.htm?gclid=CISz2-n2m5kCFRwDagodTU5aCw or

  This one

  http://www.cablewholesale.com/cgi-bin/googletrack.cgi?URL=/catalog/usbadaptors.htm&gclid=CKSK9qP3m5kCFSMSagodPAaICw

• Should there be locking plates and joints locking on cartridges on Color LaserJet CP5225?

  We ask the support of HP in Russia several times, but they cannot tell us:

  should there be blocking plates and locking seal on cartridges on Color LaserJet CP5225 or not?

  
  Maybe it is not the correct names for these articles in English, but I hope that my question will be understood.

  We just bought this printer and have a dispute with the store on this theme.

  It is a very major question for us in the situation.

  PS why the manufacturer regional technical support is unable to answer this simple question?

  P.S. We also wrote to Russian technical support via the HP web site and have no answer for more than two weeks!

  The cartridges are shipped in the printer and when you first power that they go through a process called alienation, the cartridge is 'open', so the toner is not in contact with the drum, closed power for the first time the toner cartridge and drums can work. in the United Kingdom, when the training I often show engineers one ankle clothing, we use Spring hanging out washing on a line, squeeze one end and the other opens, it is similar to the alienation, a cam turn, based on the cartridge and opens or closes.

  There are no seals or strip to remove, you unpack the printer, plug in and turn on, alienation is preparing the cartridges.

  There is a known issue with the loss of magenta or cyan, the symptom is the color will be poor and can fade in page or it is may be missing completely.

  One is there is a black plastic Panel, when you open the door, it is above all the cartridges, this can loose so that it touches the magenta or cyan causing loss of color, in some cases this Panel comes off when the printer is shipped.

  It can be difficult to see, but if you remove the cartridges you can see left and right panel is in contact with the metal frame (when you look up at the top of the cartridge cavity), in the Middle you may see a gap of 3 or 4 mm and the Panel may be a little lower When the alientates of the cartridge during printing it touches this Panel and rub off.

  If it is the plastic Panel, it can be very difficult to see the small space, we saw that several times in the United Kingdom and sometimes replace the Panel in order to ensure a good fit.

  I can't put the photos of this on an open forum and here, the opinion of HP is not public, so this is a situation that you would need to print test pages and HP would repair or replace if necessary.

  Without being rude, it would sound the store aren't give you good advice?

• Color LaserJet M277dw MFP: Cartridge not recognized after HP recently updated.

  I can use WIndows 10 if the fix is available for this OS.

  I recently updated my HP LaserJet, and after the update, he refused to print, scan or copy. The error message on the display says: "Cartridge not recognized" and it has a large image of the yellow and black cartridge, cyan and magenta those smaller, but below. The printer has a wireless connection to internet.

  Any help would be greatly appreciated.

  Thank you

  Hello

  Install the following firmware for your printer, and then look for a difference:

  http://support.HP.com/us-en/drivers/selfservice/swdetails/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/swItemId/kJ-149905-2

  Kind regards

  Shlomi

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• Color Laserjet 2550 L and XP SP3

  Hello

  I installed XP SP3, last week and since I was not able to print from my color laserjet 2550 L printer. I tried the windows troubleshooting printing suggestions for the use of different drivers, but no luck. Any body out there got any advice, it's a pain not being able to print.

  Thank you very much

  If there is no Purifier not listed on the Web site nothing listed in your programs menu or add remove software window, then all you have is a base driver installation.  Following the steps listed for remove driver and the entrance to the server properties should be sufficient.  Manual uninstallation is for printers that have utility programs or use Software Solutions of Support or Director.  Even still, following the instructions provided here should at least bring basic functionality.

• LaserJet pro 177: bought used hp color laserjet pro mfp m177

  Installation disk arived broken. How can I do to replace it.

  Just upload what you want the site web theHP.

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

• HP Color LaserJet 4550: HP Color LaserJet 4550 PCL XL error

  I use this printer for years.  It works beautifully.

  Windows 10 has just done an update & the printer driver disappeared.  I use this printer with a HP Jet Direct J4135A usb card.  Now any driver or what I do I try to install or use, I get the same error message.

  I am trying to use the printer driver's upd-pcl6 - x 64 - 6.3.0.21178.exe.  The printer driver appears in the settings & is by default we & they say that everything works correctly.

  Can you help me please?  I don't want to go out and buy another printer.

  PCL XL error

  Subsystem: KERNEL

  Error: UnsupportedProtocol

  Operator: 0x0

  Position: 0

  Found the solution for everyone that might have this problem.

  Just right click on the printer icon in the Device Manager and select printer properties / Advanced / change & driver driver HP Color LaserJet 4550 PCL6 ranking to HP Color LaserJet 4550 PCL6 and click OK.  That's all there is to it.

  Now, it will work with USB (HP Jet Direct J4135A Card) that is not supported, instead of just supported network.

• HP Color LaserJet Pro M177 MFP: HP Color LaserJet not able to connect to connected HP

  Hello

  I try to activate my printer (HP Color LaserJet M177fw MFP Pro) ePrint and much more, but I'm not able to do it cause connection problem, I guess.

  When I'm trying to 'print the information sheet', for example, the printer is not able to connect (stay on 'Sign in' loop indefinitely).

  My printer is less than a Vodafone EasyBox router, with firewall disabled and no specific barriers defined by me.

  Should I set some port forwarding (even if they should apply to ignore the firewall, when turned on) or any other specific configuration in the router?

  the same connection problem, of course, it happens when I do touch printer and console web administration, of course.

  In addition, I'll let you know that my router is not blocking access, for example, to-from the web (i.e. I am able to manage my NAS from the outside, since he admitted to a DDNS) and other local devices

  I alreay set 8.8.8.8 and 8.8.4.4 as DNS pri/sec and had an output of cycle after the series of DNS.

  My printer also has a static IP address (defined by the DHCP protocol, based on the MAC address), so not a problem, I think.

  Thanks in advance for your help,

  Lorenzo

  Hi Lorenzo,.

  To enable Web Services fumctionality, you'll need to install the latest firmware on your printer (version 20160525)

  You can locate the current version of your printer by selecting configuration > reports > Page of Configuration, the firmware version is listed under the information section on the printer.

  Updated the firmware on Linux by following these steps, but I don't know if the latest firmware is available for Linux or not, try:

  http://hplipopensource.com/hplip-Web/tech_docs/man_pages/firmware.html

  If the latest firmware is not available for linux, temporarily install the printer on a Windows PC or a my and install the latest firmware:

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

  Kind regards

  Shlomi

• HP Color Laserjet M277dw MFP: Cannot scan HP Color Laserjet MFP M277dw on Mac OS 10.6

  Hello, I can not scan to network drive using the above mentioned printer. Scan to USB key is possible.

  I downloaded the update (version 20160331) firmware image, but impossible to install the program. After double click, nothing happens. Any ideas?

  Thank you and best regards

  Christoph

  Hi Christoph,

  The printer is not compatible with Snow Leopard, it is supported on Lion (10.7) or later versions.

  You can find the system requirements below:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-Pro-MFP-M277-series/7089945/model/7089949/document/c04515051/

  The update of the firmware utilitywas not desinged for your operating system and therefore does not work on it.

  As the connectewd printer to a network, follow these steps to update firmware directly from the menu of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04517106/

  If the implementation of scan to a shared folder on your grave down Mac, please specify the exact error, and the parameters used (path of the shared folder used, etc.) also well done you have shared this folder your Mac form?