Computer laptop Windows 8 is not connecting to wifi after update

Similar Questions

• My accounts on my laptop Windows 8 will not connect to wifi.

  On two of my accounts, she claims that my wifi is limited, although it works well. On a user account I just do well, the wifi works very well and does not say it is limited. Anyone have any suggestions on how to fix this?

  The accounts would be microsoft accounts. I actually received an error message wifi has shown to be "limited." No, I did not any changes to the computer before that happens.
  Right now, the accounts have connected to wifi without problem, without doing me anything. Thank you for your answer to help me solve my problem and if the problem comes back, I will return to these methods to see if one of them solve the problem. Thank you.

• 7 original slate does not connect to wifi after update

  My daughter-in-law has a 7 Slate origin. It was working fine; connected to our wifi without problems, etc. I used it the other day and noticed there was an OTA update so I installed. Now, the Tablet does not connect to our wifi at all. I tried to do a factory reset, but it still won't connect. You can see my SSID and seems to try to connect; the wifi symbol shows the signal strength but gray remains and refuses to turn blue and complete the connection.

  Is there anything else I can try to make it work?

  As a contributor of top of page on the Forums of media consumer, HP, HP gives me access to the HP Slate 7 more free of charge so I can better answer questions on the Forum.

  Why not to delete the network connection original, that you used to connect to your router and then scan for wireless devices?

  @abo999

  As seen in the screenshot below pictures, go to the settings--> Wi - Fi and click on your SSID and then click on forget. Scan and when you see your SSID again click on connect and provide the password. This should work for your question.

  

  

  Once you have done this, connect to the SSID of your router again.

  The nice thing about operating systems, it is that there are usually several ways to attack and possibly solve the problem.

• Computer laptop Lenovo G500 does not connect to wifi when I travel.

  I've had this problem since day one. A support person of Lenovo managed to connect when I first became aware of the issue, but it would not log the next time I was in a hotel. The support people with the service provider for the hotel wifi could not help me. Drivers have been checked, windows has been updated. Microsoft security essentials antivirus running. At home, I connect to internet through my ethernet cable.  I travel quite often and my laptop is useless, unless a wired connection is available. Help!

  Hi Mario,.

  I imagine the inconvenience that you are experiencing. I appreciate your efforts to resolve the issue. I will certainly help you in this matter.

  This problem can occur if authentication enable IEEE 802. 1 X for this network checkbox is enabled. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period. This problem can also occur if Wi - Fi drivers are not updated properly, or due to changes in the network settings.

  Try these methods below and check.

  Method 1: run it Troubleshooting Internet connection problems.

  Try to run the Internet Connection Troubleshooter that can help you solve the problems with the internet connection.

  1. Press the "Windows + C" to activate the menu of charms or move the mouse to the bottom right of the screen and you will get the menu of charms.
  2. Click Search , and then select settings.
  3. Troubleshooting of type and select Troubleshooting.
  4. Click network and Internet , and then select Internet connections.
  5. Click Next to run the troubleshooter.

  If the problem persists, follow method 2.

  Method 2: Disable IEEE 802 authentication. 1 X.

  To disable authentication IEEE 802. 1 X, follow these steps:

  1. Click Start, type ncpa.cpl, and then press ENTER.

  2. Right click on your wireless network connection and then click Properties.

  3. Click the wireless networks tab.

  4. Under preferred networks, click your wireless network, and then click Properties.

  5. Click on the Authentication tab, click to clear the authentication enable IEEE 802. 1 X for this network check box and then click OK twice.

  If the problem persists, use method 3.

  Method 3:

  Follow the steps in the Microsoft help articles below:

  Why can't I connect to the Internet?

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

  Thank you

• Satellite Pro L300 will not connect to Wifi after hibernation

  Hello

  can someone there help me please?
  I have a Satellite Pro L300 and it does not connect to Wifi after hibernation.

  The only way to do it is to restart the pc.

  Any suggestions?

  Hello!

  I m using a Satellite L300, which should be similar to yours and I peut t noticed this problem. WiFi works perfectly without any problems.

  In any case, I would recommend updating the driver WLAN and the BIOS. The two you can find on the Toshiba site:
  http://forums.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In addition, you run the factory settings or you have installed a different version of Windows?

  Good bye

• computer laptop Windows 7 saves not CD / dvd

  my computer laptop windows 7 is no recorded any cd / dvd... Ive checked everything on my computer and online, but couldn't find a solution! does anyone else have this problem? If so how do solve you this problem? Help, please...

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and

  
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Computer laptop Windows 8 does not properly connect to 8.1 Win mobile wifi hotspot - connection indicated as 'Limited' (no internet connection)

  Hello

  None of our laptops Win 8 appear to be able to connect to a wifi hotspot (internet sharing enabled, and apart from the wifi on the handset) provided by our Win mobile (Nokia Lumia 635) 8.1, there seems to be a connection between the phone and the laptop, but it is presented as 'Limited' (no internet connection).

  Same phones can provide the internet connection through the internet even setting for laptops Windows 7 without any problem of sharing.

  What additional settings are there to win 8 laptops that require an adjustment?

  Thank you!

  Hi Susanna,.

  Welcome to the Microsoft Community Forum.

  I understand that you are unable to connect your laptop 8 Win to Wi - Fi hotspot. I appreciate your efforts to solve this problem, I'll probably help you with that.

  Check the following Microsoft Help article and if you have activated inhalers of Internet connection on your computer, it will lead to problems of this kind.

  http://Windows.Microsoft.com/en-us/Windows-8/metered-Internet-connections-FAQ

  If the problem persists, try the procedure described in the following Microsoft Help article and then check if it helps.

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  See also the following Microsoft Help article.

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8

  Hope this helps, please get back to us for additional help on Windows. We will be happy to help you.

  Thank you.

• Computer laptop Windows 8 will not let me connect, and the code to reset are not sent

  I just got a new laptop lenovo yesterday, I've set up and it was perfectly fine, I've been in and out of her signature today without any problem, until that earlier. I stopped him an hour ago and now I can not connect, it is said that the pasaword is incorrect when I know it's because I can connect anywhere else for what is right. I tried to reset my password several times but I do not get a code.

  The cat has worked.  Turned on emails telling me that a reset code would be sent received in my Inbox, but the emails with the codes have been sent to my spam folder.

  Thanks for your help!

• computer laptop Windows vista may not start

  I have a laptop windows vista that can not boot up to windows

  1. when I on the laptop, it loads a black screen with 5 choices
  1. safe mode
  2 network in safe mode
  3
  4 last configuration:
  5 launch the window normally
  I tried to enter in all of the choices of 5... whatever choice I go, the laptop will just keep loading and loading and loading forever bar and I waited 15 minutes and finally the computer laptop 1 blue screen flash and it has restarted and it loads again to the black screen with 5 choices
  No idea what can do with him?
  Please help me.
  Thank you

  Hello

  ·         What is the full error message?

  .         Were there recent hardware or changes to the software on the computer before the show?

  I suggest you to remove the devices connected to your computer (except keyboard and mouse) external and check if you can start the computer.

  Method 1:

  You must disable the auto restart in case of failure system on your computer and note the error message receive you on the blue screen and you need to post back to us.

  To do this, you must start your computer on the Advanced Boot options , and select Disable automatic restart in case of system error.

  Follow this link provided below to start your computer in Advanced startup options.

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Method 2:

  Follow the steps in the article, and check if that helps.

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly

  http://support.Microsoft.com/kb/958233

  Method 3:

  If you have Windows Vista DVD you can try running the Startup Repair and the Tool of diagnosis of Memory Windows to check and Windows Recovery mode if it helps.

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Alternatively, you can use the command prompt on the recovery mode windows to perform analysis and error correction on a drive letter of your choice by running "chkdsk x:" where x is the letter of your drive. Type the below command on command prompt, and then press ENTER:

  X:\>chkdsk/f

  /F Corrects errors on the disk

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• Computer laptop Windows 8 does not load in front of a black screen. Any ideas?

  My Windows 8 portable (only 6 months) does not load it just starts with a black screen after it has passed windows screen load. Last thing I did on the laptop was an update of the system. Unable to get into safe mode or anything just stuck on the black screen with the mouse cursor. Can anyone help please?

  Hi Stewart,

  Did you do changes on the computer before the show?

  You can follow these methods and check if it works:

  Method 1: Unplug all external devices connected to the computer except keyboard, mouse and monitor and check if the problem persists.

   

  Method 2: If the method above does not help, then you can follow the steps in the below mentioned Microsoft article and check.

  Windows 8 starts with a blank screen after a standard or hibernation

  http://support.Microsoft.com/kb/2756559/en-us

  Thank you. Please come back for any clarification on this or any issue of Windows. We will be happy to help you.

• Computer laptop Windows XP does not start? Help

  Hi I have a windows xp laptop I think that their system eis or something like that... Whenever I start the laptop, he's going on the error you get when your dosent laptop shut down correctly. If I click on start normally the bar will spend about a quarter of the way and then just stayed forever and only safe mode also gets a freeze from then. Y at - it something wrong with the laptop or what. How can I get my laptop to work again... someone help me please.

  It is up to tell you to us what brand of system and the model is... not "system ist or something like that."

  When you choose to start safe mode and you can see all the stuff being loaded and the system crashes, which is the last line on the screen to say?

  If you attached an external equipment, especially USB devices, disconnect everything and then you can see if things seem better.

  If you get an error message windows system config, exactly what he says?

  No error paraphrased messages please!

  It was something like this:

  Windows XP could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM

  Which usually indicate some sort of corruption of system files may be a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).  None of this seems familiar?

  If you can boot from a CD, you can create a CD bootable XP (no XP media required) Recovery Console and run chkdsk with correction of errors on the afflicted to start System.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget what you have (no XP media required).

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• computer laptop Sony vaio does not connect to internet

  Any help, my computer laptop vaio does not connect to the internet, wireless or lan help!

  Hello Alex,.

  Welcome to the community of Sony.

  Try to run all the steps mentioned here t solve the problem of Internet connection on your computer: http://community.sony.com/t5/VAIO-Networking/my-sony-vaio-always-cannot-connect-to-the-internet-some...

  Note: If my post answered your question, please mark it as an "accepted Solution".

• Not connecting to itunes after update

  Well I just installed the latest update for iPhone/iTunes, and now my devices does not connect to iTunes.

  I tried uuninstalling and reinstall the software for the device, changed USB ports, changed cables and even turned the computer and phones power on and off and still no joy.

  My phone load when I plug so the cables are very well

  Try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates.

  TT2

• Smartband SWR10 not connection with phone after update of Lifelog

  After yesterdays updated my smartband does not connect with the phone. No data is transferred and the message inside SmartConnect says "Connect charger" (but I don't know that it is fully charged). Same situation was around a month ago, and it's getting boring. Is it possible to fix it?

  OD, double relocation at all connected with smartband and restart helped smartband. I have node know what was the problem, but it is resolved.