connect to the wifi of comments, but not host wifi

Similar Questions

• WRT54G v4 works PC connected to the router... but not of wireless signal

  The subject says it all.  A few things before this.  One is that we did pass the router in another room.  But things has worked well for a few days after that.  Before just what is happening, I used my phone inter-tel (plugged into the router).  PC and phone continue to have access to the internet... as I say, wireless in the House.  Fact stop and start all.  All unplugged / plugged in.

  Updated the firmware and it did nothing.  Some would like to help.

  After an update of the firmware, you must reset the default router, and then configure the router again from scratch.  If you have not done this since your last update of the firmware, please do it now and see if it solves your problem.  If you have saved a router configuration file, DO NOT use it.

  To reset the router press and hold the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  Settings wireless-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.

  Click on the Wireless tab

  -Here the wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the channel 11-2 wireless, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  XP:
  Click Start and goto the control panel and double-click on network connections, right click wireless network connection and click Properties.
  Now, in this window, click on the second tab of wireless network and give a check mark on "use windows to configure my wireless" and then delete all network names present in the preferred networks window. Then click OK...
  Right click on the wireless again network connection and then click View available wireless networks and try to re - connect to your network...
  Now, it will give you the opportunity to put the network/wep key, make sure that you enter the correct network key and confirm...
  It will connect...

  Vista:
  Click Start > Control Panel > Network and Sharing Center > manage wireless networks, here to remove any present network and close the window.
  Click on connect to a network and try to re - connect to your network, he must ask for your key/password network, enter the network and password correct key and click on connect...
  It needs to connect... Once you're connected, you must restart the computer, it needs to connect to the Internet...

• Connected to the point of access, but not the internet.

  I install an access point using a router. With windows 8.1 I am able to connect to this access point and internet access.

  But not other computers with windows 7. There are connection but wireless adapter show without internet access.

  Try almost everything that I know. Am I missing something?

  I hope someone can give some advice? Thank you very much

  1. you can try Microsoft Fixit from the following link:

  http://support.Microsoft.com/kb/299357/en-us

  2. press the key Windows + R-> type services.msc-> press ENTER. Click Yes if prompts UAC. Then, look for the WLAN auto configuration service. Double-click it and check whether the service is started and running. In addition, make sure that the startup type is set to automatic.

  3. If the steps above could not solve the problem, kindly open command prompt, run the following command and post the result here:

  ipconfig/all

• HP Photosmart 6510 series connects to the network and Internet, but not the computer.

  Hey all,.

  I have a desktop H8-1228 and 6510 e - printer.  I got both products at the same time.  I did the initial installation, and everything worked perfectly.  I was able to print of my HP Touchpad (the printer was on the floor and my Touchpad was down.).  Recently, I made a trip for two weeks.  I turned off the printer.  This seems to have been a mistake.  Now, he will only contact my network and Internet, but not the computer.  The Setup program keeps telling me that it is 'Impossible to find the printer' and that he wants me to check the IP address of the printer.  I did this many times by printing the HP's Configuration Page from the printer screen.  I also used Windows "Add a printer" without success.

  I have installed and uninstalled the software several times; every time that remove the icon of the printer and the Standard TCP/IP port in the "Devices and printers" section in Control Panel.  A few minutes earlier, I used Regedit to delete any reference to the series of HP Photosmart 6510 in the registry, believing that it could help my situation.  There can be no. :-(  I did the installation with the same problems that I had all the other times that I tried to install it.

  No help from you the printer experts will be greatly appreciated.  I'm not a novice as you can see.  This situation, however, launched my posterior. :-))

  Hi old_geekster,

  You may want to enable disable all startup programs in msconfig until you are able to access the Web integrated printer server. It seems that there is something in the communication with the printer's operating system blocking. It will most likely software firewall or security related.

  HP has designed a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity: The HP Print and Scan doctor. HP recommend you to download and install Print and scan doctor no matter what time you need to solve a problem with your HP printer from the link below.

  I would like to know what are the errors you receive?

  http://www.HP.com/go/tools

• MAC: can connect through the Skype Web site, but not through the Skype APP itself?

  I guess that the SAME password should work for the TWO the Skype Web site and the Skype APP. However, if the website sign - it works very well, the Skype APP has a msg: "Skype cannot connect." I'm using Version 6.3.0.602 on an iMac running the latest software of Yosemite. Solutions? What I am doing wrong? (P.S. I hear, there is a version 7 for Mac, but when I go to the site to download the "most recent" version, I get the above mentioned 6.3xxx.

  OK, I 'solved' myself. I downloaded a "dmg" on the site yesterday (7.2 v), but when I started to drag the 7.2 app in my apps folder, he "warned" in ERROR that I was running a later version on the computer. So, I did not install 7.2 yesterday.

  Today, I checked the version on the computer 6.3xxx vs the downloaded 7.2, and of course the 7.2 has been later. Ignore the message warning and dragged to the app folder and it logs how.

• Socket connection in the Simulator with MDS, but not on the curve

  Hello

  Working on an application using socket connections.

  SOC = (SocketConnectionEnhanced) Connector.open ("socket: / /" + address.ip_number + ":" + address.port_number + ";") deviceside = true");

  Proceed to use a DataInputStream and DataOutputStream to communicate.

  The server works, can transmit very well with the Simulator, but also another curve (not same model). (There is a small chance that deviceside = true has not been passed as a parameter when we tested on the curve, which would go through BES? This is probably still there however).

  IMHO, this means the places that the question could be one) how the code is implemented on the client phone or b) phones or their settings (have 4 curve 8530 s on the same CDMA network).

  -These phones have already activated in the last days, is there the chances that something is missing from the service book to allow socket connections? (I doubt that what I downloaded messenger ping I assume uses taken... and everything is fine).

  No authorization application that I put?

  Ideas! Please let your mind flow. Thank you!

  To all those who might find this thread after encountering the same problem:

  The issue was with the DataInputStream... available() was ALWAYS return zero, even if there are more bytes to read. This is our 8530 s curve 4 tests phones. Tried on another curve and "BOLD" and they did not have this problem.

  Use available() stopped and tried reading for much bigger than one of our packages will be (5000 bytes).

  Have some phones to test with 5.0.0.337 that they would not work with that.

  After the 5.0.0.1000 they all work perfectly.

  I read somewhere that the available() issue has to do with J2SE-> J2ME problems, something on a wrapper. This problem exists (or existed) with TSL/SSL apparently (sorry I can't find the thread I get this info, if someone really wants to see him answer and I'll get the link in the history of my browser of laptops).

  Hope this helps someone!

  B

• I am not able to connect to the main wifi network but can connect to the network of comments.

  Hello

  This is something new, I am facing to where I am not able to connect to a main network of airport extreme, but can connect to the network of comments. Guest network works perfectly fine while the main network does not connect to devices in the home. I also found that none of my base stations are visible in the airport utility (I Airpot extreme and Airport Express on the same network). Help, please.

  The first step in troubleshooting with this type of problem is to perform a complete network power cycle on your network. If you decide to do...

  Power off all the devices on your network... modem, routers, computers, printers, etc... in any order you want.

  Wait a minute

  Turn on the modem first and leave a few minutes, he managed by itself

  Turn on the next device that is connected to a modem and leaves turn a good minute

  Keep turn on devices one by one at a time, one minute apart, until the entire network is back

  Recheck the network and report on your results

• My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  Hello BrooklynWM!

  I definitely want my iPad to stay connected to the Wi - Fi connection while I use it.  Thanks for posting that other iOS and OS X devices have no problem with the connectivity dropping.  We can try a few things.

  Would first go through the steps listed in this article: If your iPhone, iPad or iPod touch connects to a Wi-Fi - Apple Support Network

  Then if it does not help, you can check network settings with this: recommended for the WiFi routers and access - points Apple supported

  After trying those, if you still see the drop connectivity, make sure the iPad Pro is updated with iOS 9.3.2 and check to see if the connection when you are in a certain place, time, or one event happening elsewhere in the House.

  Best regards.

• iPhone connects to the wifi but does not connect to internet

  I have an iPhone running iOS 9.3.2 6s (last updated).

  The phone connects to the wifi network, but even if it's to show the signal strength is good, the phone does not charge any internet content (weather, FaceBook, email, etc.).  If I disconnect WiFi and use the data, it works very well.  We have no problem connecting to the computer or a smart TV network wifi and internet connection.

  This also happens with my daughter 5s iPhone and iPad for my son.

  Sometimes it will work fine on wifi, then a little while later I can't get anything to load. And it can be like right now when I'm at home alone is not as if there's a big load on our wifi.

  We have high-speed internet by cable (25 MB/s download speed) and a router Lynksys EA3500.  Encryption is set to WPA (not WEP).

  I tried to go into my phone settings and reset the network.  Always problems.

  It's really frustrating because you eventually switch to our mobile data and use it instead of our data ' wifi '.  And then to go on our data on our phone plan

  Here's a tip for the user on the problems of Wi - Fi. Suggest from the top and bottom. Maybe one of them will help you.

  (1) perform a forced reboot: hold the Home and Sleep/Wake buttons simultaneously for about 15-20 seconds, until the Apple logo appears. Leave the device to reboot.

  (2) resetting the network settings: settings > general > reset > reset network settings. Join the network again.

  (3) reboot router/Modem: unplug power for 2 minutes and reconnect. Update the Firmware on the router (support Web site of the manufacturer for a new FW check). Also try different bands (2.4 GHz and 5 GHz) and different bandwidths (recommended for 2.4 to 20 MHz bandwidth).

  (4) change of Google DNS: settings > Wi - Fi > click the network, delete all the numbers under DNS and enter 8.8.8.8 or otherwise 8.8.4.4

  (5) disable the prioritization of device on the router if this feature is available. Also turn off all apps to VPN and retest the Wi - Fi.

  (6) determine if other wireless network devices work well (other iOS devices, Mac, PC).

  (7) try the device on another network, i.e., neighbors, the public coffee house, etc.

  (8) backup and restore the device using iTunes (ask for more details if you wish).

  https://support.Apple.com/en-us/HT201252

  (9) go to the Apple Store for the evaluation of the material.

  Council: https://discussions.apple.com/docs/DOC-9892

• Why my computer connects to the wifi via time capsule, but not my iphone, ipad or smart tv?

  Yesterday, there was an internet outage in my area. Eventually he returned to the top, but I could not always connect. I phoned by internet service provider and finally they got it working, except now my computer connects to the wifi, but my iphone, the ipad and the smartTV won't. I use a time capsule to connect. Help, please!

  This modem do you have? Brand and model please.

  It is configured as a router or bridge?

  There is a good chance that the TC I messed up in the trouble... It happens.

  Back to the factory and repeat installation... no file is lost it doing.

  Who is your ISP? What kind of services to wide band?

• iPad does not connect to the Wifi on the range 192.168.0. *.

  I have an iPad Mini (ME860BA) on os 9.3.1 that would not connect to my wifi at home.  He began to abandon their studies repeatedly a few months before and then just wouldn't connect at all.  It is on the os 9.3 so I upgraded to 9.3.1 but it did not help.  I was able to connect using a hotspot from my phone but no go on the real wifi. Sometimes it seems impossible to connect and others it seems to connect but without the wifi icon that appear (and internet access). All other devices connect to the House without exception (or question) - it's just my iPad.

  I followed every bit of advice I've found - turning wifi off & on, forgetting network, reset all the network settings, hard reboot, reboot normal, turning airplane mode turn off again, go up the brightness of the screen (odd) and finally I restored my router and the iPad to factory settings.  Nothing worked, so I took him to a store of Apple and waiting for the genius to see me I thought I would try to connect to the wifi and it went all right!  I felt a little silly to start with but they still took a look and said that he had 'something' bad, but they didn't know what.  Their best guess was that it was something to do with password authentication because they are client wifi has no password.  I returned home and disabled the security mode of the router - I have a Virgin Superhub running the 2.4 and 5 GHz primary wireless networks - no amount of adjusting the security modes (remove the password, make visible SSID, change of Protocol) makes all the difference.  However, knowing that it worked on wifi from Apple in the store, I was really puzzled.

  After ages bother with different parameters (especially in my router), I now know why it does not connect to home... My Virgin router to short on a range of address DHCP IP of 192.168. 0. * and my iPad suddenly won't connect unless the beach is 192.168. 1. * or higher.  (It connected OK for 2 years).  It took weeks to find this out, but at least now I can connect.  I turned on the wifi of comments because it uses the gamme.1.  Everything is good, connects the first time, every time!  I have not tried establishing a password (I was so happy, it connected I left because it was... well as I switch on the MAC filtering, for a little extra protection) I could try side password later and if it still connect, I'll update my post.

  My solution is very well when I'm at home but is not going to help if I get the iPad with me - it will be hit & miss if I can get the WiFi also.  Must be set correctly - I see no that it is hardware related, so there must be a bug in the software/firmware.

  Anyone having problems connecting to wifi can try the workaround network comments - at least it will get you.

  Is there a future fix for this?

  Re: iPad wifi suddenly does not save

  Change the range on the router you want to connect to.

• HP Deskjet 3055 A does not connect to the WIFI with security

  I'm trying to configure a Deskjet 3055 A on my DD - WRT router.  I am a highly qualified network engineer, so I don't know 100% what I'm doing.

  First, DD - WRT supports WPS connection, because these are very precarious.  This means that my only way to connect the pritner to my home network is to connect to my PC and use the Setup utility (downloaded from your page drivers) I use the 28.8 version.

  My router supports the 2.4 and 5 GHz and I know the printer is only 2.4 GHz.  I disabled completely the 5 GHz network in order to connect the printer, even though it shouldn't have any effect.

  I restarted my router and reset the printers wireless network using its integrated control panel.

  In any case, after a shameful 2 hours troubleshooting, I did discover that the printer WILL NOT CONNECT to the WIFI network if any security is applied against it.  It works 100% fine with open security however, it is totally unacceptable.

  I tried both WPA Personal and WPA2 Personal, both with the same effect.

  For reasons to try, I added also the printer to my network WIFI open and tried to manually change the setting WIFI via webinterface of printers, however, whenever I try and access the wireless configuration wizard, I simply get an error message saying "Internal system error" - eventually I managed to work around this another bug that has been there for years (see http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Internal-System-Error-prevents-access-t...

  After installing printers web interface WIFI, the problem is always the same and it does not connect.

  HP, we were in the order of 2500 of these printers for users of our remote site.  If you don't come to the top with a quick solution/bug fixed, consider the lost business!

  Concerning

  Ian

  After playing well, I managed to find a solution for this!

  For all users who are unable to find a solution by using the other methods, here's what to do.

  Change your local network to open the safe but note your WIFI settings for your default installation.

  Connect the printer to the open network the HP software (via USB cable)

  Go to the URL of the printer, but make sure that you connect through HTTPS - if you get an internal system error, keep refreshing until it works (WHAT A JOKE!)

  Click on 'Network', then click 'Advanced' on the left.

  Enter the network settings as they need to be secured.

  Downstairs, check "in an infrastructure network, use 802. 11b / g behavior (assuming that your assisted supports g, otherwise use the b only option), then click on apply.

  Turn on your wireless security, on your router and then the printer should connect!

  I am really confused as to why this is not automatically enabled, if the printer is not working with security on a Wireless N network wireless, then have this as the default!

  HP - feel free to thank me in this post!

• HP laptop could not connect to the WiFi network

  My HP Pavillion G6 connects to the Wifi/Home network. It worked fine until recently. It can see the network but will not connect. My product number is C9M83PA #ABG. There running Windows 8.1. Very frustrating. Help, please

  Problem has been fixed. It seems that HP and Windows 8.1 did not get along! After you connect the laptop to the internet via an ethernet cable, I was able to use the HP Wizard to download the updates. I then rebooted both the laptop AND the router and everything works.

• M177fw does not connect if the WiFi extender is activated

  Main WiFi router's CISCO E4200

  WiFi Extender is TP-LINK TL-WPA4220

  Printer is HP LaserJet MFP M177fw Pro

  Date of the firmware: 20130823

  Install Smart SW Version: 20/06/2013 1.0.13171.352

  Printer is in the same room as the CISCO router.  Extender is located in another part of the House.  Extension signal is low near the printer.  The Extender is turned off, the printer immediately connects to the WiFI network.  When the extension is enabled, the printer tries to connect several times and fails.  All computer iPhone, iPad, laptop and smart TV in room normally works with the CISCO and extension under voltage, but the HP printer does not work.  Is there something I can do to fix this?

  This has always been a problem with 2 AP make sure the router and the Extender are on different channels, like 1 & 6, 6 & 11, 1 & 11.   Where is the printer, set this AP to channel 1.  Try now.

• PlayBook of blackBerry Smartphones does not connect to the WiFi PRIV "hot spot"

  BlackBerry PB does not connect to the WiFi PRIV "hot spot". Implements immediately with an android tablet based - Hudl of Tesco UK - but the PB comes not to connect to the private. Reading through various bulletins and cannot find anything obvious that I missed. PB connects to the other wifi fine.

  Sorted. And so simple. Just changed PRIVATE WiFi "hot spot" to 5 GHz. thanks to Bruce using BlackBerry.