Designjet 500 error 22:10

Similar Questions

• Designjet 500 error 86.01

  Hello
  Can someone help me with this error, I checked many instances and their share, I know that it is caused by a paper jam or a worn belt.
  I have this printer from someone who obviously had a go before, he had a missing transport Bush and two screws missing petrol station. I've sorted but there still problem, new belt with very little dust around looks spindle motor, have replaced the cables as soldering a few contacts were ragged and faded, the new trolley and cleaned and oiled guide bars. I also have a new band (not yet equipped) encoding the original looks ok through a magnifying glass. Power it will through diagnostics and transport moves approximately 1/4 "to the left and back to 86.01 position error code, this is the case whenever I post transport. I tried checking the system, but there are locking in an attempt to drive the cart. Can a faulty spindle motor this error code? also the engine Board axis can give same code? If so someone know a method to check one or both of these components.

  There may be more that just this fault, I suppose it shouldn't be able to until you press the power button, unfortunately it is one (starts immediately when it is plugged). Also, it is not off in failure mode. Steady green power led turns green after being pressed, constant on and off with the Panel displaying the same error code flashing.

  Any help appreciated
  Rob

  Hi bobmcm581,

  The Designjet is a commercial product.  I you a link towards the Designjet forums try to repost your question here for better coverage.

  Designjet Forums

• Designjet 500: error 81:01 continues after changing the sensor roller encoder

  OK, as described in the title, I started to conspire problems some time previously, I invetigated one error 81:01 a problem with the sensor roller encoder, I disassembled the plotter past the sensor and I worked for a few months. Now the error is back, so I decided to change the sensor for a new, but the 81:01 error continues.

  A few times the plotter says has a paper jam and sometimes, paper begins to roll and dosnt stop.

  Can someone help me with this?

  OK, the problem was solved by changing the roller encoder sensor, I described in the title, after this error persists, l I demonstrate the tracer again and the stop error after I cleaned the optical sensor of the encoder to roll in the car. So that's been the problem, I hope this can help someone.

  (Sorry for English)

• HP Designjet 500 42: Old problem of driver update

  Hello

  I have HP Designjet 500 printer 42 in. And I can't update the old drivers. I downloaded new drivers drivers

  Installed new drivers and the printer connected to the computer. Installed printer itself. Driver version but check it shows in 6.08 (preferably printer-> subject) window.

  I deleted all drivers using pnputil.exe d Oem # .inf and printui/s/T2 orders. All the drivers of HP has been removed from

  C:\Windows\System32\DriverStore\FileRepository

  and

  C:\Windows\System32\spool\drivers\x64\3

  Installed new drivers (8.10) and pluged in the printer. Printer has been installed but with drivers 6.08. So I went to the "print management" as an administrator. Pressed on HP Designjet 500 42 by HP printer 'Manage sharing'-> "Advansed"-> "New driver"-> 'Disc' and in C:\Windows\System32\DriverStore\FileRepository I chose "dsgj510.inf_amd64_* *" folder and the dsgj510.inf file here. But could not find "HP Designjet 500 printer 42 in.". Here only:

  HP Designjet 500 42 + HPGL2 card; HP Designjet 500 plus 42; HP Designjet 500ps plus 42; HP Designjet 500PS42 + HPGL2 card; HP Designjet 510 42 inch printer and HP Designjet 510ps 42-inch printer.

  I tried to use HP Designjet 500 42 + HPGL2 card HP Designjet 500 plus 42 drivers. But printer would give an error message and do not print.

  With the help of the 6.08 driver version I can print from some software, but I need to print from AutoCAD. And AutoCAD gives me the error message "no: cannot use this configuration of tracer for one of the following reasons: the driver is not found, cannot find the device or the driver has a problem." No device has been substituted. "And I can't choose the HP designjet 500 printer in AutoCAD.

  It is a shared printer and other computers on the network have 8.10 drivers and can print from AutoCAD. Single computer, the printer is pluged cannot print because it driver 6.08.

  I found the problem.

  On the page under 10 64-bit windows this is only "HP Designjet 500 and 510 HP-GL/2 and HP RTL driver 64 bit" 8.10 drivers. And this driver is not HP Designjet 500 printer 42-inch drivers. But under 64-bit windows 8, here's two pilots. "Driver HP DesignJet 500 PCL3GUI 64-bit" 8.10 drivers and same as above. This file have drivers for HP Designjet 500 printer 42 inches and runs under windows 10.

  If HP support lazy to put all work them drivers under windows 10 for HP Designjet 500 printer.

• HP Designjet 500 42 "do not print

  Looking for help with my HP plotter. Recently, I replaced the service station and print transport. I also downloaded the driver (Driver HP DesignJet 500 PCL3GUI 32-bit) and firmware (series of printer HP Designjet 500, 510 and 800 Firmware Upgrade) to new pc XP from the original pc used for printing crashed. The printer displays indication normal and says ready for jobs however when I send a print to the printer it just shows treatment work and transport movements feeling left right at a few times, but the jobs do not print. Also, it seems to stay forever in this (suspended) mode and I have to power the printer off to return to the normal screen ready.

  What is a driver/firmware issue or hardware?

  If I try to print a configuration page it also does the same thing.

  Thanks in advance.

  Jacob

  It is a thin cable error. The ends of the cable have questions or it is not completely sitting in the cart. I guess the cable could be as bad.

• HP designjet 500 plus network problem

  Hello

  I'll need your help. I have the HP designjet 500 printer more and today I bought the HP JET DIRECT 620N NETWORK CARD. I installed inside the socket, connecting the card with an ethernet to pc cable. I went to the installation of hp on the monitor, select Yes for cfg network, ip and dhcp, I reboot the tracer and in the monitor shows he gets the local IP 192.168.1.2 as well as info from rest, which is are in conflict with other devices on the network. The problem is that im trying to find the printer over the network connections on my windows xp pro, but it does not show on the results. I don't see that there is an icon that does not give me an error. I also tried to see my tracer of the firefox browser with the local IP which has achieved and open the menu normally, showing how the network works. I tried several times to reboot pc and tracer in case they are blocked, but got the same problem. Perhaps there is a driver for win xp to see the plotter on LAN? I need to have your help as soon as possible, because a lot of work to do with the tracer and this question comes back to me.

  PS I should mention that I currently have a network with 3 pc the on the Office that they link together without any problem.

  P.S. This thread has been moved to printers - LaserJet for printers - Designjet & large Format. Forum Moderator - HP

  First off there are 2 homes EIO to the back, so you messed up there. With the power off, install the gl2 card in another location and see if you still have the problem. There may be a plaque on the slot, held in place with a screw at the top and bottom. Just remove the 2 screws and remove the cover and install the card.

• Unable to drawings SolidWorks great impression for HP DesignJet 500 via Server

  Hello

  Our company has a HP DesignJet 500 with 24 "Inker for tracing large pages of design drawings created in SolidWorks to our technical workstations.  These workstations all have Windows 7 64-bit with 8 GB to 16 GB of RAM and 1 TB of hard drives and intrigue to the drawing via on board our servers (Server 2008 32 bit with 4 GB of RAM), which connects to turn over a connection IP to JetDirect EX Plus (with a sleeve of 10 Mbit / s and a CAT 5 network cable) and a parallel cable.  Lately we had problems tracing of parts of very large assembly drawings (100 MB + size), by which desktop lock when trying to trace.  They can even preview before printing (print dialog box disappears when the user clicks the Preview button).  Restart the plotter and the JetDirect gave no results better.  The server has plotter driver installed v6.08 (data file version 2.1), and the tracer itself is on firmware 3.03 version.  No errors are appearing on the plotter except an error of 79:04 in December.  Tracing a bitmap file doesn't seem to be a problem, but I could not try the other formats again.

  Any thoughts?

  Thanks in advance,

  Michael

  In the properties of the driver, there is a tab services which must display a troubleshooting icon and you can click on "Run as bitmap".  This will allow the desktop process files to print instead of the printer, which cannot process large files.  It is the only way to execute works of old printers not designed to process.

• HP Designjet 500: Driver for Hp Designjet 500 42 invalid in Win 64

  I downloaded the driver for mi hp designjet 500 42 (c7770b) printer in windows 7 Professional 64-bit (with all the software updates for today 02/20/2015). When I double click on the exe file you downloaded here: http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=377948&lang=en&lang=en&cc=us&cc=us

  I got the message "it is not an application valid win32" and it is impossible to install.

  Hello

  You have the same error for all drivers below?

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=377948&swItemId=pl_66260_3&swEnvOid=4063

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=377948&swItemId=pl_56198_2&swEnvOid=4063

  If the same phenomenon occurs for both of the above drivers try, follow these steps, the steps for Windows 7 should be the same as those listed for Windows Vista in the article:

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c00318556&DocLang=en&docLocale=en_US&JumpID=reg_r1002_usen_c-001_title_r0001

  Hope that helps,

  Shlomi

• Designjet 500 proposed purple colors AutoCAD printing gray

  We used the Designjet for years and have several colors put in place to print gray and projected (252, 253, 254 and 25).  They have recently started with purple print.  I have run all diagnostics and calibrations and alignments available, and they are all good.  I looked at several troubleshooting sites and had no luck.  I use AutoCAD v 13.

  Assuming that the print heads are out of all the colors correctly, try this:

  The printer HP Designjet 500 and 800 series printers have a fix that was implemented in the version of firmware A.02.08 and higher. This hotfix provides additional media profiles that prevent blue to mauve color output change. This fix is only applicable to the series 500 and 800 and only if the printer has a version of firmware of A.02.08 or higher. Once the firmware has been upgraded, follow the steps below to make the appropriate changes in the Panel menu front printers:
  
  1.
  
  Highlight the menu paper icon on the display on the front panel of the printer and press ENTER.
  2.
  
  Scroll to the paper type and press ENTER.
  3.
  
  Highlight Enhanced colors and press ENTER.
  4.
  
  Select the type of paper there and then press ENTER.
  5.
  
  Press the Menu key to return to the normal display of front panel

• HP DesignJet 500: HP DESIGNJET 500

  General question... I am looking to buy a little used designjet 500 and do not see in the characteristics of the product, if it is a printer and strawberry.  Can someone tell me if the designjet 500 printer 24 inches offer traced functions designed to make signs or conrour cuts?

  Thanks in advance,

  Ken

  Hello Ken,

  Designjet 500 has the ability to cut the paper/online support right (at the end of the print job to the Cup/entity roller ring at the end of the print job), but I do not think that this option fits your requirements.

  Kind regards

  Ask me

• IIS on Windows Server 2012 R2 8.5 sends error 401.2 when change password Administrator windows local, 500 errors

  IIS on Windows Server 2012 R2 8.5 sends error 401.2 when change password Administrator windows local, 500 errors

  This particular configuration is with Coldfusion 11. There is no errors in newspapers and the w3 service still works as are application pools. All websites and app pools run with transmission of authentication request.

  ColdFusion does not work with windows authentication and may be enforced as if reconfigured integrated instance to do this, if this isn't a matter of colfusion.

  Here is what I tried:

  1 I created a new user account with admin rights and disconnected and logged in as them and then make changes to the password on the server, and that didn't make a difference.
  2. I checked that all Web sites using the request pass through authentication.
  3. I checked that the application pool is also using the application-pass-through authentication.
  4. I looked to find errors in which case newspapers but don't see anything there either
  5. I also searched a failure in coldfusion logs and saw no more relevant here either, but I got colfusion running without IIS in any case.
  6. search of the roots of web for coded passwords hard and found nothing.

  If you have any ideas or any ideas let me know.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• DesignJet 500 Panel backlight control

  I have a DesignJet 500 that I haven't used in a while and I am sure at one time given lit control panel so I could better see things, but I can't find any option for this light. Does anyone know how to do this?

  Any help would be appreciated.

  There is no backlight on LCD liquid tht, only a contrast adjustment in the front panel of the box set up printer options.

• Designjet 500 24 '': hp designjet 500

  I just got the printer HP Designjet 500 24 "."  I downloaded the drivers there.   I went to devices and printers and clicked on the new printer.  The designjet is not discovered.  Tried to do it manually, but I don't know my way around that.  Any tips?

  I deleted all of the printers I had and restarted the computer and tried to add again.  No dice.  He is grateful to my other main printer without problem.  Do not know how to move forward to get the designjet recognized so I can start printing my game.

  I went to the properties of the print server and the driver installed there - "HP Designjet 500 24 by HP" that still did not help.

  I found a link that has helped to explain how to add a local printer by using the tcp/ip address or the host name.  I finally got to work!  I struggled for a good 3 hours trying to find different ways to add.

• HP Designjet 500 more: DRIVER FOR HP Designjet 500 FILE more

  Hello

  HOW to GET Designjet 500 more DRIVER FOR Windows 10 Enterprise 64 - bit OS

  Windows 10 is not released until July 29, pilots and what products will be supported probably won't be out until close.  The HP page here says "compatibility tool soon, come back in the end of July."

  That said, I use the old driver Windows XP x 64 on my decades old Designjet 650 c in Windows 10 preview.  I think Windows 7 or 8/8.1 drivers work in Windows 10 for the Designjet 500 if there is not drivers provided.  At this point there are sixteen variations of HP Designjet 500 models available through Windows Update, including variants of the 24 "and 42" models, standards, and only, HP and Microsoft provided drivers PS mono models and color and HPGL2 drivers.

  

• Windows Media Player 500 error while finding the album info

  Trying to find info on the album, I get an error "500" in the box that opens. I tried to reset the internet Explorer, and that did nothing. Sometimes, he won't give the 500 error immediately, but it will pop up after a link or two and not quite a long time to get the information. Is there a problem with the database from Microsoft now?

  Hi, looks like they fixed, at least for me! In the meantime, I used a program called mp3tag who worked to my satisfaction. When I added an album with labels written in the mp3 of this show, WMP is still the image of the album as 75% of the time automatically. Now that the integrated working again, I rewrote with WMP data tags. GL everyone!