DMVPN Split Tunneling

Hello

Thanks in advance for any help you can give. My company uses DMVPN everywhere in the country towards the rear to route traffic small office at Headquarters. Back, we carry all of the traffic. Corporate network and Internet traffic for usage of Websense.

I have a new site to the Mexico, that I'm giving up a router in and we do not want to bring back their just Internet traffic for our internal network traffic. I can't get this to work properly. No matter what I do all their traffic going down the tunnel at HQ. I am trying to carry their local Internet to their ISP traffic.

Here is the drawing and their router config talk is attached.

This looks, it is set up correctly (all traffic not in these subnets 180.x goes to 192.168.0.1). Is there some kind of configuration of the proxy server that would send internet traffic PC above the tunnel?

The only other option is that 192.168.0.1 sends packets back to HQ somehow.

-Jason

Tags: Cisco Security

Similar Questions

Access restricted without the split tunneling

I'm disabled with Split tunneling VPN concentrator. Split tunneling has been disabled to carry the internet traffic of vpn clients via our internal web filtering server. But I must restrict access to my internal servers. How can I do that. I tried with filters/Rules but his does not work, and depending on the traffic of documents filter applies only to the traffic unencrypted.

Thank you

Avil

If you use a VPN3000 while you can apply a filter to the users configured in group. This filter can restrict access to the servers as a list of specific protocols and access. This filter certainly applies to ENCRYPTED traffic, do not know what you are referring to your last sentence.

You must first define the rules to define the traffic you want to restrict address., see here for more details:

http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/vpn3000/4_1/config/polmgt.htm#1321359

Define a filter, then add the rules you just set it to him:

http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/vpn3000/4_1/config/polmgt.htm#1007037

Thne go under the group that these users are configured with, and then apply the filter to it.

A couple of sample filter are the following:

Allow access to 10.1.1.2 and block everything else:

To block access to everything, but 10.10.1.2, create a rule that is Inbound/Forward, Source of Anything, Destination of 10.1.1.2/0.0.0.0. Create another rule, it can be left at the default value which is incoming, drop, no matter what Source Dest what whatsoever. Create a filter with the default action of the front and add two new your rules, ensuring that rule that allows access to the host 10.1.12 is above the default rule which will pass everything else.

Block access to 10.1.1.2, and leave all the rest:

To allow access to everything except 10.10.1.2, create a rule that said, drop, no matter what Source and Destination of 10.10.1.2/0.0.0.0. Add a filter that has a default action is to send, add the rule to the filter.

Notes:

-You can allow or block access to subnets simply by changing your address/mask to something like combination: 10.1.1.0/0.0.0.255

Split Tunneling does not

I'm working on an installation of the laboratory program at home with my X-5506, and I got a split tunneling configuration problem. Every change I seem to give me internet access, gives me access to the local network or remove both. The current configuration, I took them both and I am a little puzzled. I have attached the configuration. Any guidance would be greatly appreciated!

Change:
```
split-tunnel-policy excludespecified
```
TO:
```
split-tunnel-policy tunnelspecified
```
I notice you are using 192.168.0.0/24. Make sure that you do not work VPN'ing an address 192.168.0.0/24 as well (or a subnet that is also identical to your subnet that you are trying to access remotely) or it won't work. Overall, you should avoid using 10.0.0.0/24 and 192.168.0.0/24 in production networks because they are so frequently used in home networks. I also note that you have configured IKEv2. IKEv2 does not support split tunneling. SO be sure you use only the AnyConnect client in SSL mode.

Cisco ASA ruled out a specific ip address of the split tunneling

Hello

I need help with a question on the split Tunneling Configuration.

I have need exclude split tunneling networks already configured a specific ip address.

This is my setup:

Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

attributes of Group Policy GroupPolicy_Anyconnect_Access_Exception_1
WINS server no
Server DNS value xxxxx xxxxxxx
VPN - connections 3
VPN-idle-timeout 480
VPN-session-timeout no
client ssl-VPN-tunnel-Protocol
value of group-lock Anyconnect_access
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_Tunnel
field default value xxxxx
Split-dns value telefonica wh.telefonica cic.wh.telefonica telefonica.corp t380.inet
mailar.telefonica.Corp mailar.telefonica.com tefgad.com telefonicaglobalsolutions.com
telefonicabusinesssolutions.com

I need to exclude the split tunnel, IP 10.0.0.50, my question is, if I change the list access deny this IP, the supplementary tunnel will exclude the period of INVESTIGATION.

example:

Split_Tunnel list standard access deny 10.0.0.50 255.255.255.255

Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

BR,

Fidel Gonzalez

Hi Fidel,

Yes, it should work; as in your example deny 10.0.0.50/32 sholud exclude the traffic in the tunnel.

I tried in my lab, and in my case, access-list is:

split_1 list standard access denied the host 10.2.2.250
split_1 list standard access allowed 10.2.2.0 255.255.255.0

And it worked he excluded the 10.2.2.250 host.

The screen shot of the AnyConnect added:

capture.PNG

Concerning

Véronique

Windows - Internet access, no split Tunnel L2TP VPN Clients does not

Greetings!

I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

Here is the configuration:

: Saved
:
ASA Version 1.0000 11
!
SGC hostname
domain somewhere.com
names of
COMMENTS COMMENTS LAN 192.168.2.0 name description
name 75.185.129.13 description of SGC - external INTERNAL ASA
name 172.22.0.0 description of SITE1-LAN Ohio management network
description of SITE2-LAN name 172.23.0.0 Lake Club Network
name 172.24.0.0 description of training3-LAN network Southwood
description of training3 - ASA 123.234.8.124 ASA Southwoods name
INTERNAL name 192.168.10.0 network Local INTERNAL description
description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
description of Apollo name 192.168.10.4 INTERNAL domain controller
description of DHD name 192.168.10.2 Access Point #1
description of GDO name 192.168.10.3 Access Point #2
description of Odyssey name 192.168.10.5 INTERNAL Test Server
CMS internal description INTERNAL ASA name 192.168.10.1
name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
description of training3-VOICE name Southwood Voice Network 10.1.0.0
name 172.25.0.0 description of training3-WIFI wireless Southwood
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif INSIDE
security-level 100
255.255.255.0 SGC-internal IP address
!
interface Vlan3
nameif COMMENTS
security-level 50
IP 192.168.2.1 255.255.255.0
!
interface Ethernet0/0
Time Warner Cable description
!
interface Ethernet0/1
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/2
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/4
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/5
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/6
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/7
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
boot system Disk0: / asa821-11 - k8.bin
Disk0: / config.txt boot configuration
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
INTERNAL DNS domain-lookup
DNS domain-lookup GUEST
DNS server-group DefaultDNS
Name-Server 4.2.2.2
domain somewhere.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
the DM_INLINE_NETWORK_1 object-group network
network-object SITE1-LAN 255.255.0.0
network-object SITE2-LAN 255.255.0.0
network-object training3-LAN 255.255.0.0
object-group training3-GLOBAL network
Southwood description Global Network
network-object training3-LAN 255.255.0.0
network-object training3-VOICE 255.255.0.0
network-object training3-WIFI 255.255.0.0
DM_INLINE_TCP_2 tcp service object-group
EQ port 5900 object
EQ object Port 5901
object-group network INTERNAL GLOBAL
Description Global INTERNAL Network
network-object INTERNAL 255.255.255.0
network-object INTERNALLY-VPN 255.255.255.0
access-list outside_access note Pings allow
outside_access list extended access permit icmp any CMS-external host
access-list outside_access note that VNC for Camille
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
access-list outside_access note INTERNAL Services
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
no pager
Enable logging
exploitation forest asdm warnings
Debugging trace record
Outside 1500 MTU
MTU 1500 INTERNAL
MTU 1500 COMMENTS
192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
enable ASDM history
ARP timeout 14400
Global 1 interface (outside)
(INTERNAL) NAT 0 access-list sheep
NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
NAT (GUEST) 1 0.0.0.0 0.0.0.0
5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
Access-group outside_access in interface outside
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server Apollo
Apollo (INTERNAL) AAA-server Apollo
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 INTERNAL
http 0.0.0.0 0.0.0.0 COMMENTS
No snmp server location
No snmp Server contact
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
correspondence address 1 card crypto outside_map INTERNAL SITE1
card crypto outside_map 1 set of peer SITE1 - ASA
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
address for correspondence card crypto outside_map 2 INTERNAL training3
outside_map 2 peer training3 - ASA crypto card game
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
address for correspondence outside_map 3 card crypto INTERNAL SITE2
game card crypto outside_map 3 peers SITE2 - ASA
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
delimiter group @.
Telnet training3 - ASA 255.255.255.255 outside
Telnet SITE2 - ASA 255.255.255.255 outside
Telnet SITE1 - ASA 255.255.255.255 outside
Telnet 0.0.0.0 0.0.0.0 INTERNAL
Telnet 0.0.0.0 0.0.0.0 COMMENTS
Telnet timeout 60
SSH enable ibou
SSH training3 - ASA 255.255.255.255 outside
SSH SITE2 - ASA 255.255.255.255 outside
SSH SITE1 - ASA 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 INTERNAL
SSH 0.0.0.0 0.0.0.0 COMMENTS
SSH timeout 60
Console timeout 0
access to the INTERNAL administration
Hello to tunnel L2TP 100
interface ID client DHCP-client to the outside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd ping_timeout 750
dhcpd outside auto_config
!
address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
dhcpd Apollo Odyssey interface INTERNAL dns
dhcpd somewhere.com domain INTERNAL interface
interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
enable dhcpd INTERNAL
!
dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
enable dhcpd COMMENTS
!

a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.43.244.18 prefer external source
WebVPN
allow outside
CSD image disk0:/securedesktop-asa-3.4.2048.pkg
SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
enable SVC
Group Policy DefaultRAGroup INTERNAL
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
Group Policy DefaultWEBVPNGroup INTERNAL
attributes of Group Policy DefaultWEBVPNGroup
VPN-tunnel-Protocol webvpn
Group Policy DefaultL2LGroup INTERNAL
attributes of Group Policy DefaultL2LGroup
Protocol-tunnel-VPN IPSec l2tp ipsec
Group Policy DefaultACVPNGroup INTERNAL
attributes of Group Policy DefaultACVPNGroup
VPN-tunnel-Protocol svc
attributes of Group Policy DfltGrpPolicy
value of 192.168.10.4 DNS Server 4.2.2.2
VPN - 25 simultaneous connections
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
the value INTERNAL VPN address pools
chip-removal-disconnect disable card
WebVPN
SVC keepalive no
client of dpd-interval SVC no
dpd-interval SVC bridge no
value of customization DfltCustomization
attributes global-tunnel-group DefaultRAGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Disable ISAKMP keepalive
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
attributes global-tunnel-group DefaultWEBVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultWEBVPNGroup
tunnel-group 123.234.8.60 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.60
pre-shared-key *.
tunnel-group 123.234.8.124 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.124
pre-shared-key *.
tunnel-group 123.234.8.189 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.189
pre-shared-key *.
type tunnel-group DefaultACVPNGroup remote access
attributes global-tunnel-group DefaultACVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultACVPNGroup
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
inspect the they
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
: end
ASDM image disk0: / asdm - 623.bin
ASDM location Camille 255.255.255.255 INTERNAL
ASDM location INTERNAL CGT-external 255.255.255.255
ASDM location INTERNAL SITE1-LAN 255.255.0.0
ASDM location INTERNAL SITE2-LAN 255.255.0.0
ASDM location INTERNAL training3-LAN 255.255.0.0
ASDM location INTERNAL training3 - ASA 255.255.255.255
ASDM location INTERNAL GDO 255.255.255.255
ASDM location INTERNAL SITE1 - ASA 255.255.255.255
ASDM location INTERNAL SITE2 - ASA 255.255.255.255
ASDM location INTERNAL training3-VOICE 255.255.0.0
ASDM location puppy 255.255.255.255 INTERNAL
enable ASDM history

I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

You must configure * intercept-dhcp enable * in your group strategy:

attributes of Group Policy DefaultRAGroup

attributes of Group Policy DefaultRAGroup

Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com

Intercept-dhcp enable

-Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked. It is located on the Advanced tab of VPN client TCP/IP properties. Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

Alex

No split tunnel-access internet via isa in dmz

Hello

I have configured my asa 5520 v 7.2 for remote VPN. Its works fine. I need to provide my customer internet access without activating split tunnel. I went through a few example below of a doc:

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00805734ae.shtml

the preceding is not enough more me like one have different needs

I want my client VPN to ASA and access to internet, I had ISA connected to the VPN device. All my vpn clients want access to the internet, it must use this operation to access the internet. My ISA server is in the same subnet of the VPN device by using a different gw for internet access.

Pls comment

Add the below: -.

attributes of the strategy of group staffvpn

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

Disable Internet Explorer-proxy local-bypass

attributes of the strategy of group staffvpn

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

Disable Internet Explorer-proxy local-bypass

attributes of the strategy of group newstaffvpn

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

Disable Internet Explorer-proxy local-bypass

adel username attributes

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

Disable Internet Explorer-proxy local-bypass

username weppe attributes

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

Disable Internet Explorer-proxy local-bypass

Remote VPN group no matter what you want to test with. where x.x.x.x is the IP address of the ISA server computer.

HTH.

Easy VPN between two ASA 9.5 - Split tunnel does not

Hi guys,.

We have set up a site to site vpn using easy configuration vpn between ver 9.5 race (1) two ASA. The tunnels are up and ping is reached between sites. I also configured split tunnel for internet traffic under the overall strategy of the ASA easy vpn server. But for some unknown reason all the customer same internet traffic is sent to the primary site. I have configured NAT to relieve on the side of server and client-side. Please advise if no limitation so that the installation program.

Thank you and best regards,

Arjun T P

I have the same question and open a support case.

It's a bug in the software 9.5.1. See the bug: CSCuw22886

SRP527W with Split Tunnel

Hi guys,.

I just sent a SRP527W that I had lying around for a while.

Everything about the unit works as well as can be expected, however I have an obligation to perform split tunneling for VPN users.

Currently, the only way that receives the VPN client is a default route. I noticed that on site-to-site VPN and tunnels GRE, you can specify safe routes, but I can't find anything that relates to remote VPN users. This can be done on IOS without problem, but would be good for the RPS.

I'm under the latest firmware 1.01.26, so if I have not forgotten anything it would be probably for a future version?

See you soon.

Bryce

Hi Bryce,.

Nothing is overlooked, it is not possible to set up split tunneling for the VPN of the RPS server.

Kind regards

Andy

What is is it possible to use the acl extended for split tunneling on ASA?

I'm setting up VPN IPSEC RA on SAA and I would like to know if it is possible to use the ACL extended as part of the split tunneling?

Thank you!

Yes, you can use the extended ACL. See this example:http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-nex...

Kind regards

Averroès.

Web VPN/SSL - general Split Tunnel capable?

When I look through some examples of configuration for IOS Web VPN - it seems you attract to the filling of a web page of web sites that users can go to. I would be rather thin client act as client light 4.x CVPN - divided for example tunnel with access to a resource internal resource. Is this possible with Cisco VPN Web? Also - with is WebVPN any ability of the NAC?

I'm not sure IOS SSL vpn, but on the asa webvpn, there is a complete client ssl option. With this, you can either create a tunnel, or all split tunnel and the only defined networks. I hope that answers your question.

Best Soho - Split Tunnel VPN router

Hi - I'm looking for some advice for a soho router.

Basically the main feature, I'm looking for is to run, which I think is a VPN split tunnel, so that all internal clients route default traffic out to the gateway of the ISP. However, if the traffic is destined for a list of several specific subnets (x.x.x.x/24, y.y.y.y/24 etc.), then it should establish a tunnel to an only PPTP/IPSEC host and route remote traffic for these subnets via the tunnel. To be clear, that these subnets (x.x.x.x and y.y.y.y) is not attached to the end of the tunnel - which is a gateway device that will route them further.

I've been watching the various VPN router offers and is not clear to me if I can do it with a RV - 042, BEFVP41 or something like the other thing SRP521W I must be able to manipulate the routing tables directly on.

As an additional note, I have complete control over the end of SOHO - but simply an account at the end of the tunnel with (it is a service provider). The idea is to use public services for 90% of the traffic, but if customers want to access a specific set of addresses, it will forward this specific traffic through the tunnel.

Thanks in advance...

On current view, do not touch the RPS with a bargepole.

Adding access to additional subnets through a VPN tunnel is pretty standard, routing will be automatic if the VPN was established, but you must ensure that

1. politics VPN at BOTH ENDS allows your local subnet to access these networks

2. your subnet is not incompatible with other subnets or roads that can be used on remote networks

3. assuming you're OK so far, remote subnets must have a route is added to the default gateway to point to your subnet via intermediate networks

Good luck!

VPN, Internet and a Split Tunnels traffic

Please attached photo because I hope that explains what I really want to do, but here's the break down.

When a VPN Client connects to remote access to 1-ASA5510 I want all Internet traffic to send to 2 - ASA5510 instead of back to the default route. When it comes out 2-ASA5510, it passes through the content filter. 2 - ASA5510 has Split Tunnel put in place and we are trying to do away with Tunnel from SPlit.

I hope this is clear enough.

Any ideas would be helpful

Dan

Dan,

Difficult but doable! First of all, there is a nice feature in the ASA that allows configuration of remote proxy based on VPN profile by: -.

Group Policy <> attributes

use a MSIE-proxy-server method

Internet Explorer-proxy server value x.x.x.x

activate Internet Explorer-proxy local-bypass

Well Yes you guessed it - works only on Microsoft Internet Explorer.

I don't think that any policy based routing would work for you - bad luck.

But you can try another feature - traffic through the tunnel, which is normally used in the topllogy of EasyVPN: -.

http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd8060b477.html

Configuration of the ASA at the bottom, I probably would test this with the IP address of the 2651 router!

HTH.

VPN without split tunnel

Hello everyone

I have setup a VPN connection, which I can connect to. For all customers of connection, I want to give them an IP (from a subnet maybe) and let them use this IP address for all that they do.
Therefore, this:

and not current:

My inside is 192.168.1.0
My VPN IP pool is 192.168.30.5 - 200
My server (DNS, files, Web site) is 192.168.1.222

Here's my setup. I scored what I thought might have something to do with it:

ASA Version 9.2 (1)
!
ciscoasa hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
pool of IP local IP-pool 192.168.30.5 - 192.168.30.200 mask 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.253 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
boot system Disk0: / asa921 - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the object Server-25
Home 192.168.1.222
Description of the test server
network of the object server-80
Home 192.168.1.222
Description of the test server
network of the object server-443
Home 192.168.1.222
Description of the test server
network of the object server-2525
Home 192.168.1.222
Description of the test server
network of the object server-993
Home 192.168.1.222
Description of the test server
network of the object server-6001
Home 192.168.1.222
Description of the test server
network of the object server-6002
Home 192.168.1.222
Description of the test server
network of the object server-6003
Home 192.168.1.222
Description of the test server
network of the object server-6004
Home 192.168.1.222
Description of the test server
network of the VPN HOST object
192.168.30.0 subnet 255.255.255.0
the object to the Interior-net network
host 192.168.1.0
the VPN server object network
Home 192.168.1.222
outside_access_in list extended access permit tcp any object Server-25 eq smtp
outside_access_in list extended access permit tcp any object server-2525 2525 eq
outside_access_in list extended access permit tcp any object server-80 eq www
outside_access_in list extended access permit tcp any object server-443 https eq
outside_access_in list extended access permit tcp any object server-993 993 eq
outside_access_in list extended access permit tcp any object server-6001 eq 6001
outside_access_in list extended access permit tcp any object server-6002 6002 eq
outside_access_in list extended access permit tcp any object server-6003 eq 6003
outside_access_in list extended access permit tcp any object server-6004 eq 6004
outside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.30.0 255.255.255.0
permit access-list Split-Tunnel-ACL standard 192.168.30.0 255.255.255.0
no pager
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (indoor, outdoor) Interior-net Interior-NET static source static destination HOST-VPN-VPN-HOST
NAT VPN VPN-server destination (indoor, outdoor) static static source HOST-VPN-VPN-HOST
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
network of the object Server-25
NAT (inside, outside) interface static tcp smtp smtp service
network of the object server-80
NAT (inside, outside) interface static tcp www www service
network of the object server-443
NAT (inside, outside) interface static tcp https https service
network of the object server-2525
NAT (inside, outside) interface static 2525 2525 tcp service
network of the object server-993
NAT (inside, outside) interface static tcp 993 993 service
network of the object server-6001
NAT (inside, outside) interface static tcp 6001 6001 service
network of the object server-6002
NAT (inside, outside) interface static tcp 6002 6002 service
network of the object server-6003
NAT (inside, outside) interface static 6003 6003 tcp service
network of the object server-6004
NAT (inside, outside) interface static service tcp 6004 6004
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS AAA server HSS-auth-server protocol
allow only
AAA-server HSS-auth-server (inside) host 192.168.1.222
Timeout 5
key *.
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0

interface ID client DHCP-client to the outside
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal HSSvpn group strategy
attributes of Group Policy HSSvpn
value of server WINS 192.168.1.222
value of server DNS 192.168.1.222
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
Split-tunnel-network-list value Split-Tunnel-ACL
HSS.dk value by default-field
activate dns split-tunnel-all
type tunnel-group HSSvpn remote access
attributes global-tunnel-group HSSvpn
address IP-pool pool
HSS-auth-server authentication-server-group
Group Policy - by default-HSSvpn
password-management
IPSec-attributes tunnel-group HSSvpn
IKEv1 pre-shared-key *.
tunnel-group HSSvpn ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:c85ff8bf61669bef56b4dad704a4930a
: end

Hello

Change Split Tunnel VPN in full Tunnel VPN, you have really do much in your configuration.

Seems that have already changed you the 'tunnelspecified' 'tunnelall' in configurations of the 'group policy' . You can delete the setup but that defines the ACL of Split Tunnel

attributes of Group Policy HSSvpn
No split-tunnel-network-list value Split-Tunnel-ACL

Seems that you use an internal AAA server to manage authentication rather than on the SAA. I guess if you want to assign a specific IP address for VPN user/username, then it must be done on the side Server?

If you had the "username" on the SAA configurations you can set it up under its framework which "username" IP address gets when he or she connects with the VPN Client.

As naturally as you start using the complete Tunnel and all traffic from the VPN Client starts to get in the tunnel to the ASA you will need a NAT for VPN Client users Internet traffic. You can configure this NAT like this for example:

network of the VPN-POOL object
192.168.30.0 subnet 255.255.255.0

interface of VPN-POOL dynamic NAT (outside, outside) after auto source

Note that this is a manual of NAT / double NAT statement real "nat" IS NOT inserted under the 'object' , but the 'object' is rather created it can be used in the "nat" command. I see that your other dynamic PAT configurations are configured with NAT Auto / object NAT network. You can do this like that too if you wish. Personally I do like that.

But as I said before, it seems that you have already configured the VPN to be full of Tunnel. It is perhaps not as it is? While it is connected with VPN, you should be able to check the secure routes (or something like that) section to see if it says "0.0.0.0" If Yes, then it should be tunneling all traffic.

Hope this helps :)

-Jouni

Split tunnel with ASA 5510 and PIX506.

Hello

I have the production between Asa 5510 (main office) and Pix 506 VPN tunnel. It is configured so that all traffic is encrypted and moves through the tunnel. This includes remote users behind Pix Internet traffic. I would like to use split tunnel and direct Internet traffic hitting the web directly from Pix instead of going through the tunnel. How can I do this safely? Please see current config Pix below:

:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 10baset
ethernet0 nameif outside security0
nameif ethernet1 inside the security100

clock timezone EDT - 5
clock to summer time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 02:00
No fixup protocol dns
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
No fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
no correction protocol tftp 69
names of
allow VPN 192.x.x.x 255.255.255.0 ip access list one
LocalNet ip access list allow a whole
pager lines 20
opening of session
monitor debug logging
logging warnings put in buffered memory
logging trap warnings
Outside 1500 MTU
Within 1500 MTU
IP address outside 24.x.x.x 255.255.255.0
IP address inside192.x.x.x 255.255.255.0
IP audit name Outside_Attack attack action alarm down reset
IP audit name Outside_Recon info action alarm down reset
interface IP outside the Outside_Recon check
interface IP outside the Outside_Attack check
alarm action IP verification of information
reset the IP audit attack alarm drop action
disable signing verification IP 2000
disable signing verification IP 2001
disable signing verification IP 2004
disable signing verification IP 2005
disable signing verification IP 2150
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list LocalNet
Route outside 0.0.0.0 0.0.0.0 24.x.x.x
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac AMC
map UrgentCare 10 ipsec-isakmp crypto
card crypto UrgentCare 10 corresponds to the VPN address
card crypto UrgentCare 10 set counterpart x.x.x.x
card crypto UrgentCare 10 value transform-set AMC
UrgentCare interface card crypto outside
ISAKMP allows outside
ISAKMP key * address x.x.x.x 255.255.255.255 netmask
ISAKMP identity address
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 md5 hash
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
SSH timeout 15
Console timeout 0
Terminal width 80
Cryptochecksum:9701c306b05151471c437f29695ffdbd
: end

I would do something by changing the acl that applies to your crypto card. You want to know what you want to support above the tunnel and then deny other networks.

If you have:

192.168.3.0/24

192.168.4.0/24

10.10.10.0/24

172.16.0.0/16

Do something like:

VPN access list allow 192.x.x.x ip 255.255.255.0 192.168.3.0 255.255.255.0

VPN access list allow 192.x.x.x ip 255.255.255.0 192.168.4.0 255.255.255.0

VPN access list allow 192.x.x.x ip 255.255.255.0 10.10.10.0 255.255.255.0

VPN access list allow 192.x.x.x 255.255.255.0 ip 172.16.0.0 255.255.0.0

Then when the traffic is destined for something other than these networks, it will go not to the ISP instead of the tunnel.

HTH,

John

Internet access without split tunneling VPN PIX

I have a PIX 515E with code 6.31. I installed a VPN to allow access to the internal network from the Internet using the Cisco VPN client. It does not work properly. We have some sellers who demand that we come from our Internet IP range to allow us access to their database on the Internet. This works very well for our internal users, but I will allow users VPN for this also.

Is there a way to allow the user from the VPN client to use the Internet for business access to the internet instead of use the split tunneling to access the internet through their own connection? I would like users to vpn to be NAT would have réécrirait Internet and seeming come from our pool of Internet addresses. What I found references by using the split tunneling, but this won't work for me. Am I stuck getting a VPN concentrator to achieve?

Thank you

Josh

[email protected] / * /.

The PIX cannot route a package back on the same interface, he entered the, which includes a customer entering the interface external and routed VPN package back on the same interface.

A router or a VPN concentrator would be able to do this, but not a PIX, sorry.

DMVPN Split Tunneling

Similar Questions

capture.PNG

Maybe you are looking for