F380 weird impression

Similar Questions

• How do I do a weird impression & same page with a deskjet 3052

  Is that what I can do to add the functionality to print odd or even pages on my deskjet 3052 a?  This would allow the 2-sided printing.

  Hi Roylrobey,

  Follow the steps below to change the settings for printing for the odd or even pages.

  1. open the printer preferences

  2. click on the paper/quality tab

  3. click on the Advanced button

  4. change the Pages to print the option under the characteristics of the printer

  

• HP deskjet f380 - get msg even if properly connected offline

  I received a HP Desket F380, which has not been used for two years while the cartridges are dried out.  I downloaded the latest driver and replaced the black print cartridge, but I am reluctant to replace the color one as well in case it does not work.  When you ask to print from say MS word or internet I get printer offline despite being able to scan a page for my lap top.   Please note that I was told by the previous owner that the printer will always print if only the black cartridge is full.

  Any ideas for what to do?

  With thanks a lot

  Hello

  Please run the impression scanning HP doctor

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-129932-1&cc=us&DLC=en&LC=en&OS=4063&product=1128296&sw_lang=

  hope this helps

• Weird minimum brightness of T430 capping issue in point 8.1 of Windows

  Hello

  I have a weird problem. I bought my T430 with Win 7 in. Now that I've upgraded to Windows 8.1, the brightness of the display will get weak after a certain point.

  In Win 7, I could turn down the brightness of my screen at a VERY small point. But currently, with 8.1 Win, although I can turn down the brightness of several points, the brightness of the display would be stuck to, say, 20%.

  1. This is the brightness for the 2nd lowest level:

  

  2. now, here, it is at its lowest level. Look, there is still another level to go:

  

  3. Although there is still a level to go (as shown in the image above), if I try to take the brightness to the lowest setting absolute, ABSOLUTELY NOTHING would happen.

  

  This problem occurs in Win 7 Pro. My lowest brightness level was much, much lower in Windows 7 as in 8.1 Pro Win. He started straining my eyes!

  Help, please!

  Thanks in advance.

  Finally! Found the solution.

  Updated my BIOS and now it works fine.

  Thanks the lenovo support team. You guys have been impressive. Keep up the good work.

• Emails from Windows Mail (only those!) incorrect impression

  It is on behalf of my mother, who I'm helping remote...

  She just bought and installed an HP Officejet 6500 Wireless all-in-one all in one printer to use with his laptop, running Windows Vista. Apparently everything is going well, except that she is unable to print correctly, emails from Windows Mail.   What emerges from the printer is about the left third of the email, printed on the right third of the paper.  It's so weird, I downloaded an analysis of the example of it at:http://img177.imageshack.us/img177/3729/emailscan.jpg

  I have consulted the laptop remotely and checked everything obvious like size settings - not that I see a lot of alter, paper, but does not include what could be wrong.  It's only the emails that are affected, and there are two weeks that they were very good impression on his printer previous (one another, but very old, Officejet).

  Any ideas please?

  Thank you

  Windows Mail uses the same as Internet Explorer print engine. It seems that the left margin is way.

  In IE: File | Page layout. Default is 0.75, (19mm), all around.

  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA

• HP Deskjet F380

  I have a deskjet F380 who gave me excellent service. 4 days ago it stopped talking to my computer or at least on the side of feeling that's as I can still scan documents in. I'm not particularly computer savvy, but I tried to reinstall the drivers and software that came with the printer. It can print a page of test manually, so it is obviously in full working condition and I lived the gamut of online help and he gave me :-) The LPT1 port is obviously working properly I can still scan and save documents, but I'm the Director of a local company and on the side of impression is the most important for me... Help!
  Dai Wright

  The suggestion of Jabzi below worked like a charm and I am eternally grateful, thank you very much.

• DeskJet f380 problem of driver for windows 7... need urgent help

  Hello, im the owner of a HP deskjet f380 and has used without problems in Windows xp, it is practically new, because I bought a couple of months. I had an update on my PC and installed Windows 7 to go with the new system, and now when I try to install the drivers for your site... those for Windows 7 32 bit, I get a weird error message telling me that I am using a bad system, WIndows XP, to be more precise. I have checked and rechecked my installation of windows and I'm sure it's Windows 7, so I don't understan why I got the message. I even tried to install the package XP, thinking that maybe that will work if Setup, my Windows is XP. It did not work eighter, I started recieveing a few errors 'file missing' of some .inf files and some .dll which are missing or cannot be accesed. The problem is quite urgent so if you can send me it please with the solution I would me more apriciative. Thank you.

  Hi Uuf11, the printer software installation is recommended in safe mode. Safe mode is primarily used to resolve problems with Windows by only running the bulk of Windows operating systems and device drivers. Once the passage in secure mode, the user can execute commands and charge the devices one at a time. So in this mode the print spooler service is not started which is essential for the installation of the software.

  As suggested steps to come to your question did not work, you can try the steps below:

  Note: The printer must not be connected to the computer before beginning the installation.

  (1) perform a disk cleanup. Start ==> All Programs ==> Accessories ==> System ==> Disk Cleanup tools

  (2) right click on the software driver that you downloaded and select "Run as" or "Run as Administrator". Enter the user name and password. This information is on your user profile on the computer.

  Note: Make sure that the driver that you downloaded is supported for the OS you are using. If you have doubts redownload the file.

  If the error persists, then:

  1) click on the Windows icon in the bottom left of the screen of the computer and in the 'search' in a box type, %Temp% and press enter on the keyboard. This will open the Temp folder

  (2) open the last file 7z

  (3) double-click the file hpzsetup.exe

• PS and LR produce bad impressions, but other programs are not...

  It's a little long, because I did a bit of investigation, but I can't solve my problem and I need help:

  I had a nice workflow that I have used for years.  I'm sure that many of you would find a bit tedious and I will not go into the details of it, but the important part is that I always printed on Photoshop (Extended CS6 - now at 13.0.3 - Yes, I have the window trial stupid bug, but that's another matter).  My monitors are profiled (no printer profile custom, but I have downloaded profiles suitable PixelGenius for times where I need them, and with my management of colors, my impressions were quite specific.)  I use and Epson Stylus Photo R2880 and I was very happy with it.  I work mainly on an iMac 24 "(millésime 2009)."  Recently, I decided to change my work flow based entirely on some of the tutorial videos that I bought of LL.  I decided that I was ready to integrate much more LR in the workflow, especially now that he understands the proofing.  Due to the new workflow I was really looking forward to printing off LR.  Who should you get more or less current.

  So far, I haven't printed with my new workflow and I would say that I haven't printed anything since 13.0.1 on PS and LR 4.1 (not that I was printing from LR at the time).  Having not printed in a while, I knew that I needed a head cleaning (of course I did) and, as is my habit, once the head was clean, I printed (from LR) a 4 x 6 image I had planned on printing to a larger size.  It collects all persistent grime after a cleaning.  Printing doesn't look just right for me (too dark and the colors were a bit wide).  I met with wrong colors prints once before, and it turned to be a driver problem.  In the process, I found a large image that is indicative of a certain type of problem and I keep the good and bad prints of hand... just in case.  I decided to print this picture, and of course, it came out looking like the standard version craptastic I was getting into with the bad long time driver.  Just to check that it had to do with my new process, I printed the picture of the PS (which worked fine the last time I printed this image). Also, it came out all wrong (the same as LR all wrong).  Since the bad impressions looked like the old 'bad driver' impressions, I thought I knew what was going on and worked with Epson to reset my printing pipeline and reinstall my printers (I also have a workforce of 845 for printing "throw" and for my wife to use).

  With new installs for my printers in place I went ahead and printed again... and once again, it came to pass badly.  I was, to say the least, discouraged.  As a last test of consistency, I loaded the image up in Nikon Capture NX2 (version 2.3.1) and did a print using the same color profile.  All of a sudden feel perfect.  It is my 'good' old prints and, equally important, was a Dead Ringer for the image on the screen. At this point, I guess that for some reason any LR and PS not correctly color managed.  I thought they were ignoring my selection of color profile and let the printer manage printing from the native color space (ProPhoto RGB) or.  To test this, I set up printing in PS (same image), but took a very strange color profile (Nikon DBase for v3.0.0.3002 of the NAVE).  It's odd how radically a color profile that I could find (the colors are mapped to completely different areas).  I was hoping that printing would be unchanged, but unfortunately he is out with the weird mapping that provides this profile.  It is so drastic a change, I have a hard time assessing whether it is 'off', as the other impressions are.  What is apparent is that PS at least (I have not tried in LR), it's actually reproducing along the pipeline of printing color information.  This does not explain why LR and PS of 'bad' impressions but not Nikon Capture.  This is where I am.  Apparently the color management is broken in my Adobe products, but works very well in my Nikon software.  I'm a bit of a loss. I'm sure I'm printing off LR and especially PS, correctly to 99.999999999%.  Anyone have any ideas?  I'd like to be able to print again. Impression of Capture NX2 is really not a good option.

  Thanks in advance,

  David

  Just to close it entirely, I just got the phone with Epson and they confirmed that if you have PS or LR color management, EVERYTHING must disengage in the printer including the option of 16-bit driver.  You will always get 16-bit printing via the PS color management.  Apparently the option "Off (no correction color)" and the 16-bit box operate independently of the driver and if one is on there as a conflict with a managed utility printing color.  I just wanted that along.

  Thanks again for all the help,

  Dave

• Weird printing artifacts in LR3.3

  Hello

  I'll try to get some decent impressions of LR3.3 but get a weird behavior with the color Orange. This happens not only in LR3.3 but also in Photoshop (CS3 to be exact). I've included some screenshots of Photoshop to show what is happening (as LR never lack...). The first shot is the picture of a couple of orange pearls of origin, the second shot shows what comes out of the printer with the rendering intent 'perception' (but 'parent' gives similar results). The dark shapes that you can see in the second shot are reflections of objects in front of the beads, only much more pointed out that in the original where you really need to zoom to see what whatever.

  The strange thing is that if I take the picture of Ligthroom in Photoshop, convert it to sRGB and then printing, objects do not present.

  Anyone has an idea why this insistence shows (and does not appear when you use sRGB)? Of course, I understand that the color is so intense/saturated that probably, it is not in the range of the printer, but I expect a smoother result of "percecptual" or "relative" rendered.

  

  

  There is really no way to get out of LR indeed. Really need proofing. Although in general the changes with proofing are subtle, there are many cases like this where you can get very large and unexpected effects. Another typical example I meet is the color of blue sky which can give more than subtle shifts cyan or purple on printing or conversion to sRGB. Or deeply saturated red and orange who lose details on printing that we see in rock informed by setting or Sun rising. There are a few tricks to get a test well. If you are on Mac OS X, you can simply press 'Preview' in the print dialog box, and you'll get a flexible preview sound proof of the image that you select the profile of the printer in the print dialog box. You can also print a JPEG and inspect that. Those are all very kludgey well and real Proofing would be very useful.

• Weird lines and do not wake

  My computer has been acting since weird transition to macOS Sierra. When you log in you get these weird lines. They do not always. Also, I noticed when disconnection and pushing the standby button it wake up and I have to stop it and start it up. I didn't want to reinstall sierra. Who took about two days.

  Retina 5K, 27-inch, late 2015 3.3 GHz Intel Core i5 16 GB 1867 MHz DDR macOS Sierra 10.12

  Material or something is very wrong and I would like to call or make a Service appointment as soon as POSSIBLE,

  help > desktop Mac Service response - Apple Support Center

  FWIW I've updated 2 old iMac and several other year of the Mac Mini to Sierra. Each of them updated in less than 30 minutes and no having problems or ill consequences.

• iPhone 7 weird noise ticking after sending message sound

  Hello

  I use an iPhone 7 for 4 days now and yesterday, I, after I send a message (using iMessager, Wechat or Whatsup), I started noticing a sound weird/click tick immediately after application. That weird noise resembles a small distortion in the enclosure which happens after some noise is played.

  Did anyone encounter the same problem?

  Thank you in advance.

  Best regards

  Ricardo

  Same here, but also after taking a screenshot. Shortly after the sound of the camera.

• How to make El Capitan to recognize my Canon printer I've done what I think is everything: one clean install of El Capitan (another problem); Reinstall the software from the CD; Anon same impression reset. No luck at all.

  How do El Capitan to recognize my Canon printer? I did what I think, that's all I can: clean install of El Capitan (another problem); Reinstall the software of Canon from the CD; same impression reset - my printer shows not yet up! I tried LAN and USB.  No luck at all. The printer does not yet appear upward on the tree of USB in the reporting system.

  What printer model Canon...?

  kologano wrote:

  The printer does not yet appear upward on the tree of USB in the reporting system.

  This looks more like a bad USB cable or bad printer.

• Login screen of the MacBook is weird.

  Hello! Login screen of my computer is weird. The colors are darker and the cursor moves more slowly than usual. Everything started after I updated my MacBook (retina, 12 inch, early 2015) to OS X El Capitan 10.11.6. Everyone knows about this problem? Is it possible to fix it?

  If that had happened to me, I would try Safe Mode boot because that passes through a few additional system checks.

  Try safe mode if your Mac does not end commissioning - Apple Support

• I lost my phone 2 weeks ago. Now, I received a message telling me to connect to find my iphone but the link is very weird

  I lost my phone 2 weeks ago. Now, I received a message telling me to connect to find my iphone, but the link is very weird.

  I entered my information it because I wanted to see where was my phone, but nothing has arrived. After that I connected to my laptop and I could go on my account, but it seems that my Iphone (that got stolen) are there any more and I can't locate. What do you think? would it be the thievs who send me this message on my news?

  

  This is because it is a phishing attempt to make you try to open a session, so that they get the powers they need to disable find my iPhone on your device. Do NOT click on anything and ignore it.

  Sorry, I see that you were already there and gave them the information. Your device, as well as your iCloud account have been compromised. You need to change your password immediately. Your device is finished now, you will never recover.

• Finder of freezing and acting weird

  Hi I had a couple issues Finder weird recently any help would be much appreciated!

  The finder drawing seems to freeze - can I open a folder or a new window of finder and sometimes it will be fine, but then it will be half freeze - the content of the window is not displayed - it will just be white or the background (desktop etc) is drawn in the finder window. I screen shotted because it's a little hard to describe...

  

  It seems to go there I kill finder / restart for 2-5 minutes... then the problem comes back.

  I deleted finder prefs, doesn't seem to help. I did a reboot in recovery mode and ran the repair disc utilities and which seem to help for a few days, but now back!

  I can close the windows in the finder and open new, and the question seems to come and go a little... Any ideas?

  Thank you

  Stuart

  Hello

  Start Safe Mode removes the system caches that can help.

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Then, try the Finder.