Firmware PLW400 update

Similar Questions

• Error on the UPS Firmware Dell Update utility

  Hello

  I got the error "No UPS connected or not able to make the connection" the inverter is connected by USB.  I have RS232 or USB enabled in the upgrade utility.

  I'm under UPS Local Node Manager, that's how I know that the UPS USB connection is good.

  Manager of local node said in respect of the power supply: Dell Rack/Tower UPS 2700W UPS RT LI LV 2700.  The device status for lack of UPS.

  The following information found here that I'm updating the firmware and then replace the battery followed by replacing the battery if the fault is not resolved.  I have re-sitting and replace the battery with a new battery.  The front panel of the inverter shows again the fault as well as the software after replacing the battery.  It seems that the update of the firmware is the only option for this error at this stage of troubleshooting.  However, the upgrade utility does not work.  Please help.

  Sometimes they have the management software will not allow the firmware update utility to try and work as follows:

  1. If the inverter has the NMC (Network Management Card) installed, then select the NMC in the utility of upgrade of the UPS Firmware and update the firmware of the UPS.
  2. Connect the ups to another system (server, desktop computer, laptop computer) that has neither ULNM nor would save installed. Load the utility to upgrade the Firmware of the UPS and the UPS firmware on the new system files. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reconnect the ups to the original system.
  3. Uninstall the ULNM and/or would save the system. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reinstall ULNM and/or save. Check the configuration settings.

• Aspire U5 - 710: application of Firmware & Driver updates!

  Hello

  I am using an Aspire U5-710 for several months, running Windows 64-bit 10.

  Even if this AIO machine worked great, it has a few problems with the graphics card Intel.

  The U5 - 710 has a processor Intel Skylake integrated Intel HD Graphics 530 video card.

  QUESTIONS:

  Intel has confirmed the graphic problems with its CPU Skylake. Questions that are answered:

  -l' screen randomly goes black, often when scrolling on the edge.

  -l' screen remains black, often coming out of sleep.

  These problems are occurring on almost any device Skylake, not only of Acer.

  SOLUTION:

  Intel has been publishes new graphics drivers, fixing these issues.

  More specifically: the latest de.4424 of the Intel HD Graphics 530 driver seems to solve these problems. See here.

  PROBLEM:

  Acer uses a custom/build version of the Intel HD Graphics 530 driver, so it is not possible to install the driver from Intel HD Graphics 530. We rely on Acer to provide an updated video driver to correct these display problems.

  REQUEST:

  Acer can release a Update to the U5-710/firmware drivers please?

  In addition, other Intel components (WiFi, BlueTooth,...) have newer drivers on the Intel Web site.

  Please Acer make a update your drivers with support for the AIO U5-710 device. This is a great camera, modern and smooth, but drivers need an update. They have not been updated since the release in November 2015.

  Thank you for listening and best regards,

  GunBee.

  Good news!

  Acer has released a Firmware update yesterday, invented R01. A02 for the Aspire U5-710.
  See the support site Acer Driver download here.

  ACTIONS:

  • Please go ahead and Update the firmware of your machines U5-710.
  • If you have the black screen problem on your U5-710, please check my other post on the forum here.

  Thanks and regards,

  GunBee.

• Clip the Firmware Zip: "Update Service is not available"

  Hi all...

  I just bought a Zip Clip 4 GB (I am a user of the two Clip & Clip + since 2008) and I have the static distortion between the tracks that I've read here.

  However, when I try to update the firmware, I get the following message: "Update Service is not available.

  Any suggestion or help is appreciated.

  Thankies

  So nevermind, lol... I'm too tired to do that today.  Figured it out.

• Of the EA6300 firmware auto update during installation, no random to WAN WAN gigabit drops

  Really, I just want the previous firmware, it will not return to the previous firmware, even if she has detected a version more recent and downloaded/installed. Possible problem during this update I want to redo, but not possibility because no prior firmware exists.

  Leads me to believe there is something in the previous firmware you guys want that we know or have once again.

  Serious security loophole eventually.

  The ultimate question is random disconnects Arris 822 g at the EA6300,.

  But I noticed after installing updated the link to the Modem Gigabit droped to 100Mbit negligible for speeds we have but always notworthy and anxiety.

  Have tried everything I can think of outside custom through 3rd party firmware. or change your firmware which is not necessary, but I did to belkins for their security flaws which I do class action about what I discovered with their firmware on several other class of devices.

  This is implemented for the parental units and EA is supposed to be EASY for them. I have them walked through the process just for your device does not works as advertised.

  Don't blame the Arris it worked and maintaines on other EA devices connection. I don't appreciate finger that help professionals tend to blame everything other than your device, then try not to do.

  It is a question of Linksys EA6300.

  Bought another ea6300.
  The object of dumping the firmware out of it.
  Corrupt firmware of EA6300 question of dumping.
  Installed prerequisite firmware dumped on EA6300 issue.
  Updated to the current firmware manually on EA6300 question
  success.

  Certainly wished I could have returned back.
  Or was the prior firmware available to try above.

  Now, I EA6300 to spare for NOT boning.
  More details can be found in IRC guest single channel.

• WRT610N Firmware version update Question

  I just bought a WRT610N. On the bottom of the camera, I see an indication of the V1. When I registered the device, the Linksys site told me that there is an update of the firmware (V1.00.00.1018_20080816).

  What is the best way to install it?

  Can I install the firmware before using (If Yes, what is the procedure for someone), or should I set up the device first, run and then update the firmware?

  Thank you

  Kevin

  Download and update the Firmware first...

  Download the Firmware from here , connect a computer to your router and open
  a page of Internet Explorer browser. In the address bar type - 192.168.1.1
  Let the empty user name & password use admin
  Click on the tab - then 'Administration' on
  the 'Firmware Upgrade' void tab-here, click on 'Browse' to select the
  compressed extract/No .bin or .img file and click on "Upgrade"-waiting for seconds... ".
  It shows that "Upgrade successful" after
  update firmware, click Reboot/continue and you will be returned back
  on the same page OR it will say 'cannot display the Page.
  Reset the router for a few seconds and set it up...

• WRT54G Firmware Version: update v7.00.7 Beta?

  Hello

  I have a router wireless EMEA WRT54G v7 with Firmware Version: v7.00.7 Beta. I can't find an update of the firmware on the site.

  Can you please help?

  Thank you

  Firmware update is available. Version 7.00.8 is available on the EMEA website. Click here!

  It is enough to click on "Downloads" and select the correct hardware version.

• Firmware and updates of the Addon for D90D7

  Hello

  How long do you keep the firmware updates and add-on for output devices?

  Why modules are listed per unit instead of the OS?

  Why the modules listed for my device not necessarily the add-on most recent available? For example WDM 5.5 contains new versions of Add-ons based Wyse.

  If I want Citrix receiver for my device 4.3 How long can I expect to wait to have available for my device? Or are we supposed to simply create are own packages after you cease to make updates.

  Can we expect improvements to the updates and the web in general experience finding things (downloads, forums, help, across different documents, not sure where to look sometimes) will improve with you coming under the ownership of Dell?

  Thank you

  Anthony

  Anthony,

  Let me answer each question better than I can.

  Q: how long do you keep the firmware updates and add-on for output devices?

  A: this is related to the product life cycle. This information is found at the following ADDRESS: http://www.wyse.com/support/end-of-life-policy

  Q: why modules are listed per unit instead of the OS?

  A: because the firmware is "Dependent on device", the firmware and all the Add-ons are stored in the repository based on the model of the device.

  Q: why the modules listed for my device not necessarily the add-on most recent available? For example WDM 5.5 contains new versions of Add-ons based Wyse.

  R: the only reason that I just was an oversight of the validation group.

  Q: if I want Citrix receiver for my device 4.3 How long can I expect to wait to have available for my device? Or are we supposed to simply create are own packages after you cease to make updates.

  A: there is no specific time limit that we must release the Add-ons. If you need the example of 9 Citrix Receiver) right now, you can install the Citrix receiver on the thin client or you can create your own package by using WDM. See WDM Admin Guide for more details on this.

  Q: can we expect improvements to the updates and the web in general experience finding things (downloads, forums, help, across different documents, not sure where to look sometimes) will improve with you coming under the ownership of Dell?

  A: Yes. We are actively working on moving the site of downloads to be consistent with the processes of Dell.

  I hope that answers your questions.

• the block erase CP1525nw firmware corrupted - update

  Win 7 64 bit home premium - 128 MB RAM "corrupt firmware ready 2 Download" cp1525nw printer display a message.

  Updated the firmware, I've followed the process below:

  I deleted the network printer and reinstalled as a printer USB (initially port usb002).

  Is turned off the printer.

  Downloaded the firmware using cp1520_series_Fw_update_20131028, got smiley face

  Checked the Firmware stored in windows/systems32/spool/printers

  Printer

  Got to spool print message "printing error".

  Changed the port usb001 and restared printer to spool print document "firmware update".

  Printer has begun to deal with the firmware update

  Queue is removed from the printer.

  Firmware update seems to stop about "erasing...". »

  Suggestions welcome!

  RESOLVED - printer replaced under warranty extended by retailer (Officeworks).

  Firmware could not be updated.

  Model HP no longer exists. Model HP equivalent not in stock.

  Now owner of a similar 3170CDW Brother HL cost to the original.

  > end of post

• HP CP1525nw not working after Firmware "Critical update"

  Someone else on this forum has had this problem and did a system restore to work around.  I can't do it.

  In any case, the update of the Firmware did not allow the printer to a wired network.  Still, other computers can print to it, but the computer that attempted the update of the firmware cannot send anything to the printer.  What in the print queue is there and finally the status changes from "Printing" to "error - printing".  Same thing if it's a document or the last firmware update.  I deleted the deleted control panel printer and reinstalled the software.  HPPSdr.exe says that nothing is wrong.  The printer says it works.

  The only thing I can do is printed through a second computer, not good, because the other PC must be on and not asleep.

  HP CP1525nw, Windows 7 64 bit

  Try disabling your firewall and antivirus to see if it works. If it works, fine, USB, there is something blocking when connected wireless.

• BEFSR41 v. 1 - do not get IP WAN, updated firmware to update

  I can get into the setup on the web.

  I can ping.

  ipconfig indicates that the LAN IP address is correct (192.168.1.1).

  All lights are light up properly.

  My internet connection works correctly (i.e. without the router).

  I've upgraded to the latest firmware (for this version of the router which is v.1, yes it's old).

  "But... under the tab"Status"in the setup, when I type"Release DHCP", then on DHCP renew," the WAN IP address is 0.0.0.0.  How can I force this thing to look for an IP address?

  Just can not know what does not work!

  Any ideas?  Thank you!!!

  (Mod Note: edited title)

  Assuming that you have a good ethernet cable between your BEFSR41 and router upstream (ADSL "modem" or "cable modem"), I guess the router upstream ISP (ADSL "modem" or "cable modem") is looking for a particular MAC address and is to remember your computer (since you've tried things wihtout the BEFSR41).  You have two choices.

  (1) turn off the router upstream (ADSL "modem" or "cable modem"), turn off the BEFSR41, wait a full minute, switch on the router upstream (ADSL "modem" or "cable modem"), let it resync to the line (takes a minute or two), then turn on the BEFSR41, see if it receives an IP address.

  If no, then try

  (2) to clone the MAC address of your computer on the WAN interface, repeat step 1.

  Russ

• If this isn't the case, juggling with the updates of the Firmware installation will be updated install all prerequisite updates?

  I am currently using a Netgear WNR2000v3 wireless router. I've never installed the Firmware/Software updates. If I install the latest update of the Firmware/Software

  (Firmware Version 1.1.2.10), this includes all previous updates or do I return completely and install the updates of the Firmware/Software in the order in which they were made?

  Just the last one will do.

• R6400 has not corrupted Firmware update

  I have a router R6400 AC1750. As he tried to update to the latest version of the firmware, the update has failed. Now my routers internet light constantly flashes orange and the light, the router is turned on. In addition, my internet works if plugged directly into the modem. I tried the procedure before and I tried the factory reset button, nothing worked. I have also tried to install the firmware using tfpt, but cannot get the .chk file uncompressed. I tried to use various programs of .chk as CHK-mate and Express Zip decompression, but programs do not recognize the file of the firmware that has been directly downloaded from netgear.com. Is someone can shine some light on this situation? Please help, thanks!

  I contacted the Netgear support to get a RMA # so I can get a replacement under warranty. Before receiving my RMA #, the support agent me had to solve several different ways to try to communicate with the router. Once an hour on the phone, I got the RMA and now have a replacement warranty in my possession. Just a tip, the diagnosis is free and I had to pay the shipping costs for the replacement, $17 for the advanced delivery method, it is shipping you and shipping of the defective unit back to them.

• SOLVED: Slow wireless internet passthrough after firmware update

  If I first bought a Nighthawk in July 2014 and it was great for a while. Then in the notice happened a few months my streaming services are jumping and more than usual buffering (which was almost never with the Nighthawk).

  I have a connection of 110Mbps (Comcast and through a SB6141 modem), but all of a sudden was only getting 10 Mbps (or less) passthrough on 5 G wireless band (at the beginning of the speed test would sometimes up to 50 Mbit/s, but on a few seconds would fall to nothing..)

  Cable speeds were very good. Always 110Mbps +. Tried several different channels and factory reset the router, wireless speed was still slow. Connected to the Netgear website and submitted a support ticket within 2 hours they sent me with an RMA number and the next day a new unit has been FedEx would be for me. Support rep Tech says it's a problem of material known in some units... I was super impressed with the customer service, it was seriously a no replacement of hassles that took every 15 minutes of my time.

  EXCEPT when I got the replacement router in the next few days, he had the SAME PROBLEM. As soon as the new router is on and I'm connected, I've upgraded to the latest version of the firmware, done a factory reset and down Speedtest. And I had the same problem: speed internet passthrough on all my wireless devices has been terrible. Less than 10 Mbps when I have a connection 110 + Mbps. (Wired speeds were great, it was not a problem of modem or provider).

  Again contacted support and they asked me to download the latest firmware on laptop and upgrade the router manually, do a factory reset before and after the upgrade. They also told me to try to disable WMM (made no difference speed passthrough, but lower my laptop connection between 433Mbps to 54Mbps speed!).

  I tried this... still slow passthough wireless speed.

  The only thing that has changed since I first got a Nighthawk in July 2014 (and I've run speedtests then and had a speed 110 wireless + Mbit/s at the time), is that the firmware has updated several times... makes me think...

  I downloaded the Netgear support the past 5 versions of the firmware for the Nighthawk. http://downloadcenter.netgear.com/en/product/R7000#sear...

  I then manually downgraded the Nighthawk to each previous version (do a factory reset before and after each installation) and ran Speedtest every time. Once I have got down to the R7000 Version - V1.0.3.24_1.1.20 (released 12/02/14) and ran a Speedtest, the PROBLEM has BEEN RESOLVED. Speed wireless devices (laptop, HTC a M7 and iPad Air 2) were all back up to 110Mbps or more!

  Hope this experience helps someone else... If your are affected by the passthrough slow internet speeds and it is not your connection speed (i.e. radio parasites) that is the question, there seems to be a serious problem with the latest latest versions of couple... Try downgrading to the R7000 firmware version - V1.0.3.24_1.1.20

  UPDATE: Yes, I actually tested the speed with several different devices (a laptop HP HTC a M7 and Nexus 9) each on 5G band, all compatible with the latest updates ac. I also used a few test sites of different speed (speedtest.net, comcast speedtest, cnet speed test), not had the same result all devices and hosts.

  However, I actually got in touch with Netgear L2 support for the last month... beta test a few different versions of the firmware of the Nighthawk and even spend more than an hour on the phone one night with a nice guy who told me he was on an island in Southeast Asia, part of the Philippines... This is where Netgear technical support is to halfway between China where they build them and Taiwan where engineers are. After trying all tweak he could think for an hour and not get better speeds wireless, he finally dropped out and wished me a Merry Christmas lol. Not one of these beta firmware made a bit of difference, and I hate the hours that they made me screwing around with them!

  BUT today, they released vR7000 - V1.0.4.14_1.1.50 http://support.netgear.com/product/r7000

  And to my surprise it actually worked! Not only my high speed wireless is returned (120 + Mbps)

  http://www.Speedtest.NET/my-result/4078979293 (laptop)
  http://www.Speedtest.NET/my-result/a/1131321713 (nexus 9)
  http://www.Speedtest.NET/my-result/a/1131332778 (htc a m7)

  but also my Seagate SRD0SD0 previously incompatible (3 TB) USB 3.0 external hard drive works now, too. What a bonus! The reason I bought the Nighthawk was to use as Server DLNA and the monster external HD I picked up 6 months ago only was on the long list of those incompatible with this capricious router.

  But now everything works (at least for now).

  P.S. Maybe it's in my head, but I swear to you that since the last firmware update when running speedtest now or file transfer (while heavy streaming) I can hear the router doing a greater slope electric buzzing/hissing noise is a little disconcerting... I'm not sure my brain fried by overclocked wifi will be worth a high speed in the end...: eek:

• Office jet pro 8500: firmware update - what's new?

  After several years of no update suddenly my Officejet 8500 (910g) firmware gets updated - is there a documentation as to what are the changes? The new firmware is LRP1FN1621DR

  Hello
  
  Thank you for using the HP Forums.  My apologies for jumping.

  Here are the changes for 2016 firmware:

  1. Update the SSL certificate to comply with the amendment on the cloud server.
  2. Fixed various IE11 and edge browser EWS compatibility issue.
  3. Improved security ePrint.

  Hope that helps!