Heating and noise problem laptop while streaming

Similar Questions

• Satellite A100 heating and fan problem

  Hello

  I will try to describe my problem in detail because I so hope that it might help!

  I have a 5 years A100-011, Nvidia 7600 Go satellite. Recently, I fixed a display problem that I used to, however, this time (two weeks ago) him comes from the computer laptop back from the workshop with this heating problem. Which is the first time! The problem is the fan.

  When I start the PC, the fan works like it ti be long, maximum for 3-4 seconds. After that the fan barely works! According to me, the air coming out but very very low! less than how it is used for years! I came back to the same place, I corrected the PC. They checked and claim his fine and work! So, I give it a shot and tried the PC.

  Unconsciously, there is problem. Because the temperature of the GPU that has the problem, idling about reaching 60 c (SpeedFan) and goes high (65-67) while surfing the net! And using this way too much for internet!

  What makes it even worst fan always at the same speed very slow! The speed can increase little when he reached 67c!

  In this way, I can not use any high performance program, because the PC becomes more heated then stop.

  Note: I tried the following:
  1-BIOS (latest version) no available fan control
  2 power settings does nothing and there is no option of cooling method
  3 - fan control software. Unfortunately, nothing has worked

  I don't really know what the problem is! Given that the fan works but not all the time and why the GPU gets hot without doing something really serious! What is a cleaning problem? If so, why the fan does not reach its maximum speed at this temperature. !

  I hope I am fine help and answer here!
  PLS help!
  Thank you

  I agree with the user Notepad Akuma is 5 years old and I think that there is a lot of dust and debris inside the cooling modules that prevent fans from running correctly.
  Air can circulate properly and therefore the temperature rises
  So what to do?

  You can use a jet of compressed air to remove dust from the fans that I'm doing this regularly and it helps to clean the fans

• Satellite M40-184 and noise problem

  I bought two days ago, this laptop and I already found two problems. The first is that always before the speakers seem to start working a strange noise (ICT) and it is very annoying for me. Is there a problem with the speakers.

  The second problem is that when I use the laptop for more than two hours the AC adapter also makes a very annoying noise. He is also very strong (more strong that fans or anything else). Is it normal to do what noise?

  Thank you

  Hi Manos,

  I'm not sure of the sound from your speakers, normally I wait till they're totally calm, unless a job is running that use.

  Regarding your power adapter, should make any noise at all. It can become hot for what is quite normal. I would recommend the adapter/notebook back to your provider as soon as possible.

  Kind regards

• The line detection and noise problems

  
  

  Don't open attached files. Can you try to reattach?

• Stream HP: I accidentally closed my laptop while it was restarted and now it's the juice a black screen it has been hours

  I accidentally closed my laptop while he was now to restart juice is a blank black screen, it won't do anything it's only a couple of months

  Sdyork

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post about the problems with your new HP PC and wanted to help.
  
  You should not have problems with a PC this new.
  
  While this PC is still under warranty, contact HP customer care directly so that they can put you in contact with HP Technical Support to see what they can do on the diagnosis and repair of your machine remotely.
  
  I did recently, and HP technology was able to remotely access my PC on the Internet and to make the necessary repairs.

  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!

  ---------------------------------------
  However, HP customer care is generally not available on weekends, so you will have to wait until Monday to contact them.
  ---------------------------------------

  Good luck

• I can't open the system when he was sht down. But the system was the heat and I have to remove the battery for a while and it should re-sttart, what the problem.

  I can't open the system when he was sht down. But the system was the heat and I have to remove the battery for a while and it should re-sttart, what the problem.

  Too generic a question, can you clarify considerably more for us? Your question could be reformulated in the following way and always be true?

  "I can't start my computer once he has had a BSOD. Something overheated, but I don't know. I removed the CMOS battery and replaced in order to asure me that a bad overclock on a core component has not caused the problem. Now, it restarts correctly, what is / was the problem? »
  The foregoing, what I thought you meant. The above statement is correct?

• After I install my laptop bootcamp has restarted and said there was a problem and restart your laptop then I check my memory of the laptop and my mac 210 GB is 180 GB and when I checked the scores he had only a mac partition

  After installing bootcamp my laptop has rebooted and said there was a problem and restart your laptop then I check my memory of the laptop and my mac 210 GB is 180 GB and when I checked partitions there was only a mac partition and I can't get back the deleted memory

  Post a screenshot of what shows utility disk to disk

  How to take a screenshot on your Mac - Apple Support

  OSX works OK?

• Satellite A210 - heating and BIOS update problem

  My aunt was having problems with his A210, so she bought herself a new and gave me the old one. The problems that she has been seen was the computer kept stopping at random. I think it's an overheating problem because the laptop runs quite hot. The BIOS has never been updated so I thought that might help with this problem. in any case, when I tried to update the BIOS this error message came.

  Cannot load the C:\Users\Dan\Desktop\MK10AWF\PHLASHNT driver. SYS.
  Please verify that your accounts, if you have no administrator privileges, please sign in again!
  Access is denied.
  Error code: 5

  I am the only user on the computer so I have administrator privileges and I don't know why this error is coming. Help, please. Thank you

  > Has anyone else experienced problems with the A210 of overheating? All solutions?
  Hi mate

  I m a Satellite A210 owner and to be honest, a higher internal temperature might occur if the laptop would not get enough air to cool the internal parts like CPU and GPU.
  A few weeks ago, I used the laptop on the sofa I don't the opinion of t that the cooling that are placed at the bottom of the unit fans were clogged because of my position relax, if you know what I mean ;)

  After a short period of use, the laptop shut down automatically I was a little surprised, but I realized that air could not circulate, and so the laptop overheated

  Now, I m using the unit only on the desktop. This method is recommended, and it helps to keep the temperature at the lower level

  PS: My BIOS is updated...

• scope of nor-5114 interfaced to 2576 OR multiplexter relay and a signal to test via Coax, noise problems

  Hello

  We use a system of connected steps and have questions about the best method to interface to our test design.

  DUT (Test Point [n])---> 6 ft coaxial cable---> 96pin--> NI 2576---> NI 5114 (map interface) connector

  Note1: the map interface 96pin and equipment, OR share the same floor plan.

  Note 2: We have tried with changing the setting scope NI5144 of 50 ohm and 1 M ohm but do not seem to see a difference on our potential noise problem.

  The questions are:

  (1) what is the best place to justify our coax cable shield, the side was FORCED (to the mass of Council) or on the side of 96 pins?

  (2) we currently have the shield connected on the side 96pin and it brings in some possible noise to our test had TO that point signals, we added a 100 ohm series resistor close Testpoint and it helps solve the problem, but it is not acceptable to have this resistance in the beam of cable by our client, and we try to find another option to solve this problem of potential noise.

  Any help and advice on this is appreciated.

  Kind regards

  Miguel

  Miguel,

  1.) as long as you do not adopt loops of Earth in your system, you should be fine to be implemented for the ground of coaxial cable. I didn't want to forget that it is important that your HAD is not referenced to the mass of power also because this may introduce ground loops in your system.

  2.) as for the culprit of the noise that it is the combination of the two specs you listed. Amplifiers in your DUT output are specified for less than 1/10 the capacitance of the coaxial cable. This is the origin of the noise that you see, because the op amp is unable to drive the capacitive load and causes instability of the amplifier.

  There are a few methods you can use to remedy this situation and here is a resource that describes some of these solutions.

• HP/Compaq nc6400 laptop: HP/compaq nc6400 Windows 10 and graphic problem, erasing text in areas of immersive shell.

  I have a laptop nc 6400 product number: RB518UT #ABA uses an ATI mobility Radeon x 1300 graphics card, as well as Intel (r) mobile express chipset available 965 G. I chose to use Classic desktop windows at the moment and no problem at all now. I don't know about Vsync or 2D with any partbut I disabled it Aero, windows 'themes' clear the text, mosaic with not a spec left shaows WHEREAS I could think of and still the text clears using my own slider like gum or disappears and leavesablank. Alsooccasionaly gibberish are more black lines not only any official language, but today I thought that almost a nonsense post script type to some... in some mobile tiles that can refresh, but even that does not work as it always has... I am at a loss I need a decent graphics that I use photoshop and dreamweaver allt/times a day and at least they need to exploit as much as possible. I had no problem with their execution on this computer for the past 4 years or more. It has been now 4 OS on this big machine that has not had any problems over the past 7 years. He 4gig memory and 750 GB hard drive and lack of wellis touchscreen but... not worry Windows when they checked all this to check.  I am beyond my capabilities and need help. Even if I need to build my own divers I Although it will not be the fastest answer, but I can see the need to know how the alter pilots an asset right about now.  Please you all the

  suggestions will be an asset, as I am a "what to do now the level of frustration"and would like that much more about the reason for it. " I was just as lucky as my machine has never had issues that were close to that sort of thing.

  TY for any help, answers, all possible assistance, you may think.  I hope that I have provided a clear problem, and most of the information you need. I never used a service like other instances, that raising any issues that others have as well.  Always helping if I wasn't sure but never as difficult a question as is happening now.

  Ty for any possible assistance or suggestions that can point me in the right direction.

  egcorrell

  Hello:

  The only suggestion I can offer would be manually install the graphics driver Vista support for your laptop and driver, page and see if it works...

  BTW, the nc6400 has the mobile Intel 945 chipset, not the 965.  The 6910p has the 965 chipset.

  Download and run this driver... You will probably get an error of unsupported operating system.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=1847705&swItemId=ob_59975_1&swEnvOid=2103#tab1

  Conclusion of any windows error.

  Go to Device Manager and click on the video controller (or Microsoft based Display Adapter) who need drivers.

  Click the driver tab.

  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp38833.

  Make sure that the include subfolders is selected and see if the pilot goes like this.

  Then restart.

  If your nc6400 has this problem with the SMSC Infrared driver with the! Marc, I went into the BIOS, found the menu of Ports and disabled the infrared port, saved and restarted.

  That got rid of the problem of device.

  I don't know of anyone who uses the infrared port anyway.

• Hang up during, connect and internet problems on laptop HP15-g019wm

  My portable computer product number HP15-g019wm F9H60UA #ABA has been suspended on the black welcome screen after logging about two minutes before opening on the desktop. My mozilla firefox is slow to open and does not connect to any websites other than the home page. It is upgraded to the latest version, when I first tried to open it and then it opens slowly. Google chrome opens quickly but then freezes when I try to go to another site. My computer is running windows 64 bit system 8.1. Anyone know what could be causing the issues off the phone and internet on my laptop? I was able to connect and browse the internet very well last night, and these problems just started to happen this afternoon. Any help would be appreciated.
  Thank you.
  Lynch10

  He seems to have been a problem during an update, as everything ran as usual on Sunday and continues to do so.
  Lynch10

• BlackBerry Z10 please help! m having a problem with the heat and does not

  my blackberry z10 stand up heat and my apps and setting are not open. When I click it, it redirect me to the 1st screen. even I can not open my setting too. so I can't do a securitywipe also. Help, please.

  Try a reboot first. Hold your power button for about 15 seconds, until you see BlackBerry on your screen. Don't release it before despite what may appear on your screen.

  If this solves the problem, you can reset your phone to factory specifications by using the link to BlackBerry. If I remember, once your phone is connected to the link of the button to press link Options is in the upper right and then Reload Software.

  Keep us updated on your progress.

• While the suite war Thunder game stops and restarts my laptop

  Original title: war Thunder crashing

  Hello

  I have a Dell Inspiron 7420. Recently, when I play War Thunder, the game just stops and restarts my laptop. There is no warning, all of a sudden shows a black screen and the auto restart my laptop. What happens to the login screen.

  Hi Pinaki displayed,

  Really sorry for the relply ULTRA end. BTW, it's always the same Amos. I tried reinstalliing the windows 8 and all that kind of stuff and I think it's a hardware problem. I'll be sending my laptop to a PC repair shop soon. Thx for your help! Really of sry for long wait.

• I have Photoshop CS5.1 Extended with free upgrade to CS6. How do I re acquire this upgrade?  I upgraded my laptop from Vista to Windows 7 and had problems with the way he ran I did a full clean install of Win 7 and am trying to re install all my

  I have Photoshop CS5.1 Extended with free upgrade to CS6. How do I re acquire this upgrade?  I upgraded my laptop from Vista to Windows 7 and had problems with the way he ran I did a full clean install of Win 7 and am trying to re install all my Applications

  Please refer to I have Photoshop CS5.1 Extended with free upgrade to CS6. How do I re acquire this upgrade?  I upgraded my laptop from Vista to Windows 7 and had problems with the way he ran I did a full clean install of Win 7 and am trying to re install all my

  (Double Post)

• Dumpsters and noise in audio and video players

  Hi, all my audio and video players in the laptop, the present jump (interruption) and noise, while playing, can someone help me please?

  Hi Sergiorey,

  This problem can occur if the device controller or audio sound card is out of date.

  I suggest you to see the following link for more information.

  Play an audio or video file: frequently asked questions (what can I do on the audio problems, such as popping, crackling, or sound that plays too fast or too slow?)

  http://Windows.Microsoft.com/en-us/Windows7/play-an-audio-or-video-file-frequently-asked-questions

  Post us the results once you try the steps above.