HELP, (start black screen, floppy drive 0 error of research)

Similar Questions

• Pavilion dm4 does not start: black screen with cursor blinking up to no left, no error message

  Nowhere on my HP Pavilion dm4 close last night and does not restart.  When I turn on the computer, I get a black screen with a cursor blinking in the upper left corner.  I ran a variety of diagnostics and all seems OK (i.e. no error message).

  I am able to start the computer in mode 'Media' - and I see all my files.  However, I'm unable to start the computer normally.  Help, please.

  My computer is old - 1 year and 25 days to 25 days outside the warranty period.

  Thank you.

  Hello

  Boot from the new rescue CD, select repair your computer and choose the command line.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart now.

  Kind regards

  DP - K

• Start black screen and beeps, HELP pls

  I have a HP Pavilion zv5410. When I turn it on it has a black screen and it beeps (1-2-2). I went on some sites about, but don't really understand what is happening.

  I put the new RAM in because that I was told by a techie, it was usually the RAM goes bad, but this did not help. I can't do anything with the BIOS because I can not even a screen to enter in info, even with an external monitor.

  I was told that I could get the data on my hard drive with a hard drive enclosure kit. I bought the kit box Rocketfish 2.5 inches, but it has a different connector (for individual pins where solid mieare 'PIN' this slide down into the connector of the laptop).

  Any ideas or suggestions. I'd appreciate any help.

  Thank you all,

  K

  It worked!  I feel so stupid for not trying to see if the plastic piece came out.  Thank you much for the help!

  Karen

• Help: Floppy Drive gets error "Windows - no disk Exception Message c0000013 parameters 75b6bf7c 4 75b6bf7c 75b6bf7c treatment".

  Dell Deminsion 3000, Windows XP Pro SP3, Version 2002, Pentium 4 processor 2.8 GHz, 2.00 GB of RAM disk Y-E Data YD - 702D

  A: floppy drive appears in my computer and in Device Manager where you can read it and the controllers are working properly.  But the diskette in the A: drive is not visible in disk management.  I tried UN-installing, re-installing and updating readers.  I also did that the BIOS was set to Auto & 1.44 3.5.  What can I do to fix this?

  Hello

  This problem seems to be caused by software conflicts or by malware (virus or spyware etc.).

  I suggest you to follow these steps and check if that helps:

  Method 1:

  Try to run the scan on the computer online and check if it helps:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Method 2:

  Try to perform the clean boot and check if it helps:

  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• Desktop computer do not start; black screen; keyboard does not.

  Ok.  I turned on my desktop computer tonight and all I get is a black screen.  Keyboard does not work either.  Has gone through all the troubleshooting suggestions that I could find online (using my laptop), but nothing works.  I think maybe an automatic update Windows could be the problem.  You have any tips for me on what to try next?

  Hi aljbad1,

  Welcome to Windows Vista answers Forums!

  I would like to ask you a few questions in order to get a better understanding of this issue so that we can better help you.

  (a) what version of Vista are you using?

  (c) do you receive an error message when you start the system?

  Method 1: You can try to start safe mode and see whethyou can follow the below given steps:

  1. remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  Click the Start button, click the arrow next to the button lock and then click on restart.

  2. do one of the following:

  a. If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  b. If your computer has multiple operating systems, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  3. Select safe mode and press enter

  Method 2: If you are able to start in safe mode, then you can try to perform a system restore and check if it works very well.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  2. in the System Restore dialog box, click on choose a different restore point and then click Next

  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next

  4. click on finish

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  For more information, please follow the below given link:

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista

  http://support.Microsoft.com/kb/936212/

  Method 3: you can perform a Startup Repair on your computer using your Vista DVD:

  We will have to perform the Startup Repair, boot from the Vista DVD and get RE Win and choose Startup Repair from the menu.

  1. Insert the installation disc.

  2. restart your computer.

  3. If you are prompted, press any key to start Windows from the installation disc.  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions.

  4. choose your language settings, and then click Next.

  5. click on repair your computer.

  6. Select the operating system you want to repair, and then click Next.

  7. in the System Recovery Options menu, click Startup Repair.

  8. once the Startup Repair tool is completed, restart your computer and check if it works very well.

  Method 4: you can also try a system restore using Vista DVD and check if it works very well.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Insert the installation disc.

  2. restart your computer.

  3. If you are prompted, press any key to start Windows from the installation disc.  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions.

  4. choose your language settings, and then click Next.

  5. click on repair your computer.

  6. Select the operating system you want to repair, and then click Next.

  7. in the System Recovery Options menu, click System Restore.

  8. in the System Restore dialog box, click on choose a different restore pointand then click Next.

  9. in the list of restore points, click a restore point that was created before you began to meet the problem, then Next.

  10. click on Finish

  Note: when you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  For more information, please visit the below given link:

  Repairs to the system of Windows recovery environment

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-system-repairs-from-the-Windows-recovery-environment-from-Windows-Vista-inside-out

  Hope this information is useful.
  Let me know if it worked.

  Concerning
  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 8 will not start black screen.

  It has been three days, I've tried everything I can find. I start my computer, I see the screen with the icon where you sigh, it loads and I get a black screen with a mobile cursor.

  Any help I see is to go to this or that on desktop and run everything that... I CAN'T go to my office. I can't start a backup drive (managed to get a copy, because the computer did not come with one) without getting through desktop Start menu. I can't do it in safe mode without going through the menu through my office... What am I supposed to do when ALL I get is a black screen? No amount of ctrl + alt + del or restart lead me anywhere I try to reboot and I'm frozen on a blue screen that says loading. I hard reboot and I'm back to the black screen.
  I would just reinstall, but the computer came preloaded so I don't have the keys.
  Someone help me please!
  F8 and all other combos keys that I found online, do nothing, pull up no menus, still called gateway and they said tapping deletes during the power upward would pull up the menu bridge... nothing.

  Well, I discovered something that many people do not know apparently. I called gateway and he was telling me what to do, get a crazy thought I was doing it wrong. All I had to do was press DELETE to get their menu upwards, but every time I did it I did have 'no signal' on my screen. After a huge clothing "Yes, my screen is plugged! When I don't type at least something shows to the top, etc etc... "he gave up and told me to drop it.

  What I realized: you can't get through all the menus with a connected graph card. I don't know why I didn't think, in retrospect, that should be obvious, at least to a person in the forums help much, I went.
  If you have a similar problem make sure that you are using onboard graphics (which means completely disconnect all other cards manually). Only then can come bios.
  Arrived, made a fast start, has managed to get malwarebytes running and had 11 malicious files. How my boyfriend or I took those up is still a mystery, it's funny I did some quick tests every morning and they come clean. Guess I have to do a full analysis more often.

• Help with black screen on inspiron 9400 with geforce 7800 go

  Thanks in advance to anyone who can help me

  I have an inspiron 9400 with geforce 7800 go, and for these last days, when I start the computer, I get a black screen or a very pixelated windows which then goes to the blue screen of death and said that 'nv4_disp' is blocked in an infinite loop and that there is a problem with the device or the driver, I tried out the video card and re-allocation of places She who does not worked, so my question is, how would I go to get a new card, and what other cards I could possibly updated too, any help on that would be great

  
  

• Satellite L850D does not start - black screen

  Ok.. My wife L850D had problems with black screening started upward after the toshiba screen.

  I ran a few different utilities, including a reset... it all started about 3 weeks after the victory 8.1 upgrade.

  Rang technical support who kindly informed that because we put 8.1 on that he cancelled the guarantee. (btw nice guy)
  Then refused to help.

  And went and reloaded Win 8 of my happens, just to see if it was a problem of hardware, software.
  (yes I know, but it must have been only temp).

  It starts fine, sitting there for centuries without problem.
  It wasn't until I downloaded the drivers toshiba, (Yes the good) did a reboot and hey presto. black screen again.

  A little, this would imply that there is a problem with the drivers of toshiba?

  OK so the wife decided screw it, put Win 7 on it.
  Restarted with disk in. sat and sat. Google finally informed me that I had to disable secureboot and put uefi in the csm.

  OK fine, went into the bios, off course start, changed to the csm uefi and restart the computer.
  Now I get nothing; screen all turns on, fan starts, cd rom shots on and nothing stops down immediately if I push the power button.

  I pulled the battery, external and internal, let rest for half an hour and still the same thing.

  Any ideas?

  The history is for me a little confused so let me start from the beginning with some basic stuff.
  In your ad write you didn t what model do you have exactly (L850D-xxx) and I can't check the specs of the laptop but I presume that this laptop comes with preinstalled OS, probably Win8.
  Laptop with factory preinstalled OS that includes all the necessary drivers and tools and utilities. One of them is Toshiba Recovery Media Creator. With this tool, you can create a recovery (DVD or USB) media and it lets reinstall the original OS if it s some problem and HDD recovery does not work.
  Best option now would be to use these media and install original recovery image. Did you create this recovery media?

  Generally speaking when you new notebook you do not have to use the original OS. You can install anything you want, and it has nothing to do with security. You can install any OS, all supported operating systems. So I do not understand how you could get info from technical support.

  In any case, try please connect your laptop to the power supply and restart laptop. What exactly happens? See Toshiba welcome screen? Try pressing F12 repeatedly. There any reaction?

• Help! Black screen, said disabled system [02837]

  I forgot my password and just kept pressing the keys because I was frustrated and then it came to pass just a black screen that says "System disabled" [02837] I don't know what to do. It is with Vista Home premium. Help, please!

  Hi okalani

  Thanks for posting on Microsoft Answers.

  Where you see the message system disabled?  It is after Windows Vista starts upward or before that?

  See the following information about the Microsoft policy on passwords

  Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features
  For more information about the lost passwords, please see the following Knowledge Base Article:
  http://support.Microsoft.com/kb/189126

  Ken
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows could not start - black screen

  My laptop does not start - I have a black screen with the message

  Windows could not start.  A recent hardware or software change might be the cause.

  
  

  File CLFS. SYS

  Status: 0xc00000e9

  Info: Windows could not load because a required file is missing or damaged.

  I ran the Vista startup repair disk, but results from that start-up cannot repair this computer automatically.  root cause found: critcal C:\CLFS boot file. SYS is corrupt

  I can't start in safe mode - when I try it starts to list files, stops after about 5 and then sends me the black screen message.

  Hello

  To begin with, would not be clfs.sys C:\, it would be under C:\Windows\System32. This could indicate one of the following two issues:

  (1) your boot sector is damaged.

  (2) you have a virus masquerading as a legitimate system file.

  For one, the first thing you should try are the steps detailed here: http://support.microsoft.com/default.aspx/kb/927392?p=1

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• first to start black screen

  I started the first pro test yesterday and it has only made the charge at a black screen.  After you have reinstalled it controls all the forums I can find with first and load the name I found a post that did not get an answer to my problem I see that apparently it is unique.  When I load the first coming with just a black screen, the intro messages total as well but that's all, now I reset preferences as the post says vaguely and still have the problem maybe someone can help here.

  

  

  

  Data sheet:

  MOBO - Gigabyte 970 has ud3 revision 1.2

  CPU AMD fx 4170

  16 GB DDR3 RAM-

  PSU - LSP Ultra 650w atx

  GPU Geforce GTX 970

  Hi Henry,.

  You close the home screen by pressing the X (close) button? If so, then you'd see only BLACK screen. This is normal behavior (personally, I think that is not very useful). You can click on the FILE menu to create a new project and set up the workspace as usual.

  Thank you

  Regalo

• Install and help with black screen / timeout

  I'm pretty new to the scene of the VM and try to configure the ability for my bosses to connect to a virtual desktop, while they travel.  I have setup a Viewserver, a vCenter and a main domain controller.  I send you all the traffic through our firewall through the DMZ in the Viewserver.

  When I test this connection locally from a PC on the same network through the Client view, it seems to work fine.  I have a beautiful office in Windows 7 can be used.  When I leave the office and go to any other Internet connection, I have a login name, provide connection information, and then a black screen and that's where he stays.  In the end (after 15-20 years or more) he told me that the remote connection has been completed.  Short version is it works on the inside, but not outside.

  I have reviewed this error a few messages found and have made several steps such as insurance there is no active internal firewall (will re-enable them and fix them after I understand this), checked the Viewserver can properly search the PDC, the vCenter and so on.

  I'm really stuck here and have tried different things for several days.  That's a lot of your time to test, because it works fine locally, so I have to leave the building and get an external Internet connection to test it out-> in.  I have the public IP address of the Ste of connection on its own domain.

  For the purposes of this question, it is publicip.mydomain.com

  Internally, the machines are set up as:

  PDC 192.168.11.202

  vCenter 192.168.11.203

  Viewsrv 192.168.11.204

  The firewall is DMZ had to 192.168.11.204.

  Any help would be appreciated in the sovereign.

  Thanks for the update.

  If you have double checked these three steps, then it is probably time to use Wireshark to see what is blocking PCoIP in your environment.

  Take a look at this post for more information on this. http://communities.VMware.com/message/1860992#1860992

  You can initially run wireshark on the Client from the view, and then if that does not indicate where the Eastern bloc, then run it on the Security server. Look at just the traffic PCoIP. (4172 TCP and UDP 4172).

  This is how some other people have fixed what you see.

  Select this option.

• iPhone ran out of battery, now wont start black screen after the apple logo

  Hey not last night, but the night before, I forgot to plug my phone so it died while I was sleeping. When I woke up, I plugged and went a little. When I came back I noticed that the phones screen was on, but black. I tried to restart with the buttons and everything that I do not understand what could be wrong. The battery is not cause fried, it continues to display the apple logo then a black screen. I would prefer not to have my phone back and to lose everything, and I can't really afford to pay someone more than 200 to tell my my phone is broken, please help.

  Have you tried that?

  Try a forced reboot. No data is lost during this procedure. Hold on the sleep and home buttons at the same time for about 10 seconds until the Apple logo appears on the screen.

• Satellite M60-128: start: black screen/delay/blocking

  Hello guys,.

  I have a strange problem with a Satellite M60-128.
  When I start the laptop there are a few problems:

  * Sometimes the remains of black screen (no Toshiba logo) and the laptop does not start
  * Sometimes the laptop starts normally (when he hung before and I turned off with the power button)
  * Sometimes the Toshiba logo is visible but stop there

  I also sometimes have a problem that the USB ports does not work. When I reboot, it works fine. When the USB ports fail, there is a warning in devices.

  I made an update of the BIOS (v1.60) but the problem remains.

  I noticed this: when the laptop does not start and I 'click' on the right button of the Toshiba logo toutchpad is visible and Notepad starts.

  Anyone familiar with this problem or some knows a solution? Thanks for advantage.

  Andy

  > I noticed this: what laptop doesn t start and I 'click' on the keypad touch s right button the Toshiba logo is visible and Notepad starts

  Very strange question usually the laptop should automatically start without pressing the button of the touchpad. For me, this is meaningless and it looks a bit like a motherboard problem
  What do you think about this?

  Have you tried to reinstall the operating system with the recovery CD Toshiba delivered?
  Maybe you should do to make sure this isn't a software problem

  Best regards

• Compaq Presario CQ61-420US no start/black screen

  Hi all.

  I have a compaq presario CQ61-420US having similar problems below, except I have a black screen, fan flashing lights turns is the same (num lock and cap lock) but they Flash continuously every second or 2.  I tried the hard reset with the fix of ram, connect an external monitor, change the battery and the power adapter, nothing helps. I also used the air compressed on the vents, just in case was riddled with dust because it overheats and can cause problems, but nothing.

  Any other suggestions?

  An option I can think of is to buy a new motherboard, but I'm going to try something else before that.

  AlexisGonzalezC,

  You can try the above solution the other person sugguested.

  Sorry, but it is very difficult to help without a touch your computer and troubleshoot it if there is a hardware problem.

  I predict that GPU your computer has a pseudo brazing or cold joint problem.

  Good luck.